User Manual

ManualsBrandsTeam Associated ManualsHobby1/10 RC10B64D 4WD Buggy Team Kit

Summary of content (34 pages)

PAGE 1
PAGE 2
:: Introduction Thank you for purchasing this Team Associated product. This assembly manual contains instructions and tips for building and maintaining your new RC10 B64D. Please take a moment to read through this manual to help familiarize yourself with these steps. We are continually changing and improving our designs; therefore, actual parts may appear slightly different than in the illustrations. New parts will be noted on supplementary sheets located in the appropriate parts bags.
PAGE 3
:: Hardware - 1:1 Scale View Button Head (bhcs) Flat Head (fhcs) 2x4mm (31510) Aluminum (8545) Ball Bearings 2.5x10mm (31350) 3x7x3mm (91475) 3x6mm (31541) Aluminum (8551) Titanium (91591) 5x8x2.5mm (31400) 2.
PAGE 4
:: Table of Contents 1....................Cover 2....................Introduction 3....................1:1 Hardware “Fold Out” 4....................Table of Contents 5 - 7..............Differential Build (Bag 1.1, 1.2, 1.3) 7...................Chassis Build (Bag 2.1, 2.2) 7....................Center Bulkhead Build (Bag 3.1, 3.2, 3.3) 8....................Steering Rack Build (Bag 4.1, 4.2) 8 - 10...........Front Gearbox Build (Bag 5.1, 5.2) 10 - 11........
PAGE 5
5/17 :: Front and Rear Gear Differential Build - Bag 1.1, 1.2, 1.3 - Step 1 92077 Sun Gear, Metal 92077 Sun Gear Pin 92079 x3 Shim 5x8.5x0.17 92080 Front/Rear Gear Diff Case #6588 black g rease 92078 Diff Outdrive O-Ring 92082 Gear Diff Outdrives :: Front and Rear Gear Differential Build - Bag 1.1, 1.2, 1.3 - Step 2 92079 x4 Shim 2.55x6.1x.25 92079 x3 Shim 5x8.5x0.
PAGE 6
:: Center Gear Differential Build - Bag 2.1, 2.2, 2.3 - Step 1 92077 Sun Gear Pin 92080 Center Gear Diff Case #6588 black g rease 92079 x3 Shim 5x8.5x0.17 92078 Diff Outdrive O-Ring 92082 Gear Diff Outdrives :: Center Gear Differential Build - Bag 2.1, 2.2, 2.3 - Step 2 92077 Sun Gear, Metal 92079 x4 Shim 2.55x6.1x.25 92077 x2 Diff Cross Pin 92076 x4 Planet Gear, Plastic :: Center Gear Differential Build - Bag 2.1, 2.2, 2.3 - Step 3 92079 x3 Shim 5x8.5x0.
PAGE 7
:: Center Gear Differential Build - Bag 2.1, 2.2, 2.3 - Step 4 4 ! 1 2 3 Tighten the screws evenly in a crossing order! 31350 x4 2.5x10mm FHCS ! 4 1 3 Tighten the screws evenly in a crossing order! 2 31531 x4 3x6mm BHCS 92085 B64 Spur Gear, 81T 92078 Diff Gasket :: Chassis Build - Bag 2.1, 2.
PAGE 8
:: Steering Rack Build - Bag 4.1, 4.2 - Step 1 91048 HD 8mm Ball Stud 31521 x3 2.5x8mm BHCS 92004 B64 Steering Rack 31382 1mm Shim 92005 Bellcrank Input Arm, 18mm 91048 x2 HD 8mm Ball Stud 25187 x2 3x14mm BHCS 91475 x4 3x7x3mm Bearing 31382 x2 1mm Shim 25215 M3 Locknut (Black) 92004 B64 Bellcrank 92004 B64 Bellcrank :: Steering Rack Build - Bag 4.1, 4.2 - Step 2 31400 x4 5x8x2.5mm Bearing ! NOTE: The steering rack should swing freely left and right once assembled.
PAGE 9
:: Front Gearbox Build - Bag 5.1, 5.2 - Step 2 91563 x2 10x15x4mm Bearing Arm Mount Insert, Arm Mount B 1 1° Up 25211 x2 3x10mm BHCS 92014 x2 Arm Mount Inserts Step 1: Add shims on this side to TIGHTEN gear mesh. Subtract shims on this side to LOOSEN gear mesh. 92079 x8 Outdrive Diff Shims Step 2: Add or subtract shims here to finalize diff side to side play once gear mesh is set from Step 1.
PAGE 10
:: Front Gearbox Build - Bag 5.1, 5.2 - Step 5 92038 B64 Front Body Post 25202 x4 3x10mm FHCS 596 ck #1 lo ad e thr 92038 B64 Top Plate 31541 3x6mm FHCS :: Front Gearbox Build - Bag 5.1, 5.2 - Step 6 Arm Mount Insert, Arm Mount A 1° Down 92016 B64 LRC Arm Mount, A 92025 B64 Front Arm Shim, 1mm #6588 black grea se 31531 3x6mm BHCS 92024 Hinge Pin 92025 92037 B64 Front B64 Front Arms Bumper 89202 x2 3x12mm BHCS 92014 x2 Arm Mount Inserts :: Steering Block Build - Bag 6.1, 6.
PAGE 11
:: Steering Block Build - Bag 6.1, 6.2 - Step 2 #1596 thread lock 89202 x2 3x12mm BHCS 91438 CVA Rebuild Kit, #6 5 ck 88 gre ase bla 92058 B64 Front CVA Bone. 76mm 92060 B64 Front CVA Axle 91438 CVA Rebuild Kit #1596 thread lock 92061 B64 Front CVA Retainer :: Steering Block Build - Bag 6.1, 6.2 - Step 3 9956 Front Hex Roll Pin 91560 x2 5x10x4mm Bearing 92059 B64 Front Crush Tube 92063 Wheel Hex, 5.0mm :: Steering Block Build - Bag 6.1, 6.
PAGE 12
:: Servo Build - Bag 7.1, 7.2 - Step 1 Servo not Included! 91451 HD 4mm Ball Stud 9180 Servo Horn 31532 3x8mm BHCS 9180 Servo Horn Ring ! Included servo spacers can be installed between the servo mounting tabs and servo mounts to correctly align your servo. 92041 B64 Floating Servo Brace 31622 FT Servo Mount 7337 x4 Servo Mount Washer 31532 x4 3x8mm BHCS 31521 x2 2.5x8mm BHCS 31531 x3 3x6mm BHCS 92042 B64 Antenna Mount 92040 B64 Servo Mount :: Servo Build - Bag 7.1, 7.
PAGE 13
:: Rear Gearbox Build - Bag 8.1, 8.2 - Step 2 Arm Mount Isert, Arm Mount C 91563 x2 10x15x4mm Bearing 1° - Up 92014 x2 Arm Mount Inserts 1 Step 1: Add shims on this side to TIGHTEN gear mesh. Subtract shims on this side to LOOSEN gear mesh. 92079 x8 Outdrive Diff Shims 25211 x2 3x10mm BHCS Step 2: Add or subtract shims here to finalize diff side to side play once gear mesh is set from Step 1.
PAGE 14
:: Rear Gearbox Build - Bag 8.1, 8.2 - Step 5 25202 x2 3x10mm FHCS ! NOTE: Add one drop of black grease to all screws holding the gearbox ! 25204 x2 3x16mm FHCS #6 588 ck gre ase bla 25202 x4 3x10mm FHCS 92065 B64 Rear Center DogBone, 110mm :: Rear Gearbox Build - Bag 8.1, 8.
PAGE 15
:: Rear Hub Build - Bag 9.1, 9.2 - Step 2 91438 CVA Rebuild Kit, # bla 6588 ck gre ase 92057 B64 Rear CVA Bone, 65mm 92062 B64 Rear Axle 91563 10x15x4mm Bearing 91438 CVA Rebuild Kit 91562 6x13x5mm Bearing :: Rear Hub Build - Bag 9.1, 9.2 - Step 3 Do not overtighten the #91611 SHCS! ! 92055 x2 Rear Arm Shims 91611 1.6x5mm SHCS 91436 Wheel Hex Pin 91609 Wheel Hex, 5.0mm 31510 2x4mm BHCS 92024 Hinge Pin :: Anti-Roll Bar Build - Bag 10.1, 10.
PAGE 16
:: Anti-Roll Bar Build - Bag 10.1, 10.2 - Step 2 Front Anti Roll Bar Install ! Install the roll bar into the Anti Roll Bar Coupler until it bottoms out. :: Anti-Roll Bar Build - Bag 10.1, 10.2 - Step 3 25225 x4 3x3mm Set Screw Rear Anti Roll Bar Install 31511 x2 2x5mm SHCS ! Do not overtighten the set screws. :: Anti-Roll Bar Build - Bag 10.1, 10.2 - Step 4 25225 x4 3x3mm Set Screw 31511 x2 2x5mm SHCS ! Install the roll bar into the Anti Roll Bar Coupler #92054 until it bottoms out.
PAGE 17
:: Turnbuckle Build - Bag 11.1 - Step 1 91722 x2 Ballcup 92027 3x42mm Turnbuckle ! Orient the notch to the left throughout the car. It indicates which end has the left hand threads! Servo Link Build x1 Racers Tip: Use black grease (#6588) on the threads of the turnbuckles for easier ball cup installation! 15.90mm :: Turnbuckle Build - Bag 11.1 - Step 2 91722 x2 Ballcup 91723 3x48mm Turnbuckle ! Orient the notch to the left throughout the car.
PAGE 18
:: Turnbuckle Build - Bag 11.1 - Step 4 91722 x2 Ballcup 91723 3x48mm Turnbuckle ! Orient the notch to the left throughout the car. It indicates which end has the left hand threads! Rear Camber Build x2 21.30mm Racers Tip: Use black grease (#6588) on the threads of the turnbuckles for easier ball cup installation! :: Shocks Build - Bag 12.1, 12.2, 12.3 - Step 1 31510 M2 x 4mm BHCS #1596 thread lock 91634 12mm V2 Shock Piston (1.6 front) (1.
PAGE 19
:: Shocks Build - Bag 12.1, 12.2, 12.3 - Step 3 lu kf oc Sh id id lu kf oc Sh 91449 Shock Bleeding Steps: 12mm 1. Before assembly, install each bleed Shock Cap screw 1-2 turns into the shock cap, Front Shock: 37.5 wt #5433 Rear Shock: 30 wt #5422 2. 3. 4. 5. 6. 7. 8. 9. 10. Steps 2-3 Steps 4-5 Steps 6-7 Step 8 then remove the screw. This will make it easier when you are bleeding your shocks. Pull shock shaft down. Fill shock body 3/4 full with silicone shock fluid.
PAGE 20
:: Electronics/Wheels & Tires/Body & Wing Build - Bag 13.1, 13.2, 13.3 - Step 1 92045 B64 Motor Mount Slide Motor not included! 25225 3x3mm Set Screw 31532 x2 3x8mm BHCS Pinion not included! :: Electronics/Wheels & Tires/Body & Wing Build - Bag 13.1, 13.2, 13.
PAGE 21
:: Electronics/Wheels & Tires/Body & Wing Build - Bag 13.1, 13.2, 13.3 - Step 4 Build x2 Wheels / Tires and Inserts are not included! Build x2 97 #15 ue l g CA Wheels / Tires and Inserts are not included! ! Carefully apply CA glue (tire adhesive) to the tire bead on the side. Do one side at a time, allowing it to dry before gluing the other side! CA glue not included! :: Electronics/Wheels & Tires/Body & Wing Build - Bag 13.1, 13.2, 13.
PAGE 22
:: Electronics/Wheels & Tires/Body & Wing Build - Bag 13.1, 13.2, 13.3 - Step 6 92050 x2 B64 Wing Buttons Front of Vehicle 25202 x2 3x10mm FHCS 0° - Mount under wing 3° - Mount above wing 6° - Mount under wing Painting Tips: Your B64 comes with a clear polycarbonate Wing Mount Shim body. You will need to prep the body before you can paint it. Wash the inside thoroughly with warm water and liquid detergent. Dry the body using a clean, soft, lint-free cloth.
PAGE 23
:: Shock Springs :: Shocks 4187 31327 31510 89278 91304 91310 91449 91480 91481 91491 91492 91493 91494 91495 91617 91619 91634 91721 .030 Nylon Washer VCS3 Shock Bottom Cap and O-Ring 2x4mm BHCS 2.5mm Washer 12mm Threaded Collar and O-Ring 12mm Shock Spring Cups (+0mm, +5mm, +9mm) 12mm V2 Composite Shock Cap w/O-ring and bleeder screw 12x23mm V2 Shock Bodies 12x27.
PAGE 24
:: Gear Differentials 2.
PAGE 25
:: Center Bulkhead 25201 25211 31382 31532 92044 92045 92046 3x8mm FHCS 3x10mm BHCS Alum. Washers, 5.5x1.0mm 3x8mm BHCS B64 Motor Mount B64 Motor Mount Slide B64 Center Bulkhead/Cover 20 20 10 6 1 1 1 31532 31532 31532 31532 25211 92046 31382 25211 92044 31382 92046 92045 25201 31532 25201 25201 31532 25201 :: Steering 25187 25202 25215 31382 31400 31521 91048 91475 92003 92004 92005 3x14mm BHCS 3x10mm FHCS Locknut, M3 Alum. Washers, 5.5x1.0mm 5x8mm Bearings 2.
PAGE 26
:: Front Gearbox 25202 25204 25211 25225 31511 31521 31531 89202 91563 92008 92014 92016 92018 92037 92065 92071 92072 3x10mm FHCS 3x16mm FHCS 3x10mm BHCS 3x3mm Set Screw 2x5mm SHCS 2.5x8mm BHCS 3x6mm BHCS 3x12mm BHCS 10x15x4mm FT Bearings B64 Gearbox Front/Rear B64 Arm Mount Inserts B64 LRC Arm Mount, A B64 LRC Arm Mount B B64 Front Bumper B64 Center Dog Bones, 82mm B64 Input Shaft, 17T B64 Input Shaft Retainer 20 20 20 20 6 6 6 10 4 1 1 1 1 1 Pr.
PAGE 27
:: Rear Gearbox 25202 25204 25211 25225 31511 31521 89202 91563 92008 92014 92019 92021 92065 92071 92072 3x10mm FHCS 3x16mm FHCS 3x10mm BHCS 3x3mm Set Screw 2x5mm SHCS 2.5x8mm BHCS 3x12mm BHCS 10x15x4mm FT Bearings B64 Gearbox Front/Rear B64 Arm Mount Inserts B64 LRC Arm Mount, C B64 LRC Arm Mount D B64 Center Dog Bones, 110mm B64 Input Shaft, 17T B64 Input Shaft Retainer 10 10 10 10 6 6 10 4 1 1 1 1 Pr.
PAGE 28
:: Front Shock Tower 25188 25211 25215 25612 91048 91447 91533 92009 3x20mm BHCS 3x10mm BHCS Locknut, M3 Locknut, M3 with Flange HD Ballstuds, 8mm Shock Bushing Balls Shock Bushings, Short B64 Front Shock Tower 20 20 20 20 8 4 4 1 25188 91533 91048 25188 25211 25612 91048 25215 91447 92009 25211 91533 25612 25215 91447 :: Rear Shock Tower 21173 25202 25211 25215 25612 89202 89204 91048 91447 91720 92012 92038 92050 Body Clips, Small 3x10mm FHCS 3x10mm BHCS Locknut, M3 Locknut, M3 with Flan
PAGE 29
:: Body and Decals :: Factory Team and Option Parts 1364 1366 1369 1370 31381 31382 31383 71014 71034 91118 91119 91120 91450 91452 91494 91576 91577 91580 91581 91582 91583 91584 91585 91588 91589 91592 91593 91594 91595 91596 91597 91610 91618 91620 91625 91626 91627 91628 91630 91631 91633 91699 91750 91751 91752 91753 92006 92010 92013 92015 92017 92026 92028 92029 92030 92049 92064 92067 92069 92076 92084 92097 92100 92089 92090 92091 92092 92093 92097 92103 FT Aluminum Servo Horn, 23T, 15.
PAGE 30
:: Reedy Motors / Spare Parts / Accessories :: Reedy ESC’s 252 253 254 255 256 257 258 259 260 261 262 263 264 265 266 267 268 269 270 284 285 287 Sonic Sonic Sonic Sonic Sonic Sonic Sonic Sonic Sonic Sonic Sonic Sonic Sonic Sonic Sonic Sonic Sonic Sonic Sonic Sonic Sonic Sonic 540-M3 540-M3 540-M3 540-M3 540-M3 540-M3 540-M3 540-M3 540-M3 540-M3 540-M3 540-M3 540-M3 540-M3 540-M3 540-M3 540-M3 540-M3 540-M3 540-M3 540-M3 540-M3 25.5 21.5 17.5 13.5 10.5 9.5 8.5 8.0 7.5 7.0 6.5 6.0 5.5 5.0 4.5 4.0 3.
PAGE 31
:: Apparel / Promotional :: Tools 1111 1112 1113 1114 1449 1519 1541 1545 1546 1554 1567 1568 1569 1570 1590 1592 1655 1656 1657 1658 1659 1660 1661 1662 1663 1664 1665 1666 1667 1668 1669 1670 1671 1672 1673 1674 1675 1719 1737 3718 3719 3720 3987 6429 6956 7709 FT Turnbuckle Wrench FT 4mm Turnbuckle Wrench 12mm Big Bore Shock Tool FT Dual Turnbuckle Wrench FT Off Road Ride Height Gauge FT Hex/Nut Driver Tool Set, 5pc.
PAGE 32
Kit Setup Driver: Event: Date: Track: Qualify: Front Suspension: Ride Height: 20mm Camber: -1° Toe: -1 Anti-Roll Bar: 1.2 Wheelbase Shim: Shim back TQ: Main: Axle Height: Caster Block: 7° 10 ° 1mm 0mm Ball Stud Spacing: Steering Plate: 13 ° LRC HRC 1° 3 Kit 2 1 1mm Ball Stud Spacing: Arm Mount A: Notes: Best Lap Time: Bump Steer Spacing: +3 +2 +1 0 Kit Wheel Hex: Finish: 0 .5° 3 2 1 5 4 Arm Mount B: LRC HRC 1° 0 .
PAGE 33
Driver: Event: Date: Track: Qualify: TQ: Main: Finish: Best Lap Time: Front Suspension: Ride Height: Axle Height: Bump Steer Spacing: +3 +2 +1 0 Camber: Toe: Anti-Roll Bar: Wheelbase Shim: Ball Stud Spacing: Wheel Hex: 3 Steering Plate: Caster Block: 7° 10 ° 13 ° LRC HRC 1° 1 Ball Stud Spacing: Arm Mount A: Notes: 2 0 .5° 3 2 1 5 4 Arm Mount B: LRC HRC 1° 0 .5° BA Rear Suspension: Rear Hub Link Setting: Arm Mount C: Ride Height: LRC Camber: HRC 1° 0 .
PAGE 34
Associated Electrics, Inc. 26021 Commercentre Dr. Lake Forest, CA 92630 USA http://www.TeamAssociated.com http://www.RC10.com http://twitter/Team_Associated www.facebook.com/TeamAssociated call: (949) 544-7500 - fax: (949) 544-7501 Check out the following web sites for all of our kits, current products, new releases, setup help, tips, and racing info! www.TeamAssociated.com. - www.RC10.