User Manual

ManualsBrandsTeam Associated ManualsHobby1/10 RC10B6 2WD Buggy Team Kit

#90011 RC10B6 Team Kit

Summary of content (34 pages)

PAGE 1
#90011 RC10B6 Team Kit
PAGE 2
:: Introduction Thank you for purchasing this Team Associated product. This assembly manual contains instructions and tips for building and maintaining your new vehicle. Please take a moment to read through the manual and familiarize yourself with the steps. We are continually changing and improving our designs; therefore, actual parts may appear slightly different than the illustrations. New parts will be noted on supplementary sheets located in the appropriate parts bags.
PAGE 3
:: Hardware - 1:1 Scale View Button Head (bhcs) Flat Head (fhcs) 2x4mm (31510) Aluminum (8545) 3x8mm (25201) Aluminum (8553) Titanium (91592) 2.5x6mm (31520) 3x4mm (91158) 3x6mm (31531) Aluminum (8550) Titanium (91580) 3x18mm (89209) Titanium (91597) 3x3mm (25225) 3x10mm (4671) Ballstuds Silver 8mm long (31284) Ti Nitride 8mm long (31292) HD 6mm (91047) Ti Nitride HD 6mm (91118) Shims and Washers 3x18mm (2308) Servo Mount Washer (7337) (.250 x .125 x .
PAGE 4
:: Table of Contents 1................... Cover 14.................Bag 18 - 19 2................... Introduction 14 - 16........ Bag 20 - 22 3...................1:1 Hardware “Fold Out” 16.................Bag 23 4................... Table of Contents 16 - 18.........Bag 24 - 26 5....................Bag 1 19 - 21....... Tuning Tips 5 - 7..............Bag 2 - 4 22 - 30....... Catalog 7 - 8..............Bag 5 - 8 31................ Notes / Contact Info 8 - 9..............Bag 9 - 10 32......
PAGE 5
8/16 :: Bag 1 - Step 1 31286 x2 FT Ballstud Washer, Aluminum (2mm) ! Note orientation of steering rack. Front 91667 Steering Bellcrank (Right) 91475 x4 3x7x3 Ball Bearing 91475 x4 3x7x3 Ball Bearing 91667 Steering Rack 31286 x2 FT Ballstud Washer, Aluminum (1mm) 91048 x2 Heavy-duty Ballstud, 8mm 91667 Steering Bellcrank (Left) :: Bag 1 - Step 2 ! The steering bellcrank brace has offsets on one side. They should be installed towards the bearings.
PAGE 6
:: Bag 2-4 - Step 2 91652 Side Rails (L & R) 31284 8mm Ball Stud, Long Servo screw not included! 25202 x4 M3 x 10mm FHCS Servo not included! 31286 FT Ballstud Washer, aluminum (2mm) 89009 Servo Horn Ring 9180 Servo Horn 25201 x6 M3 x 8mm FHCS :: Bag 2-4 - Step 3 91724 Steering Link, B6 A - Airtronics F - Futaba H - Hitec J - JR 91719 x2 Servo Mount 31286 FT Ballstud Washer, aluminum (1mm) Printed here ! 4671 M3x10mm Set Screw 91724 x2 Servo Spacers ! Align the servo horn 90 degrees Tighten
PAGE 7
:: Bag 2-4 - Step 5 89202 x2 M3 x 12mm BHCS ! The front hinge pin brace has a sharp edged side, and a rounded edge side. Mount the sharp edge side towards the bulkhead.
PAGE 8
:: Bag 5-8 - Step 2 91049 Heavy-duty Ballstud, 10mm 31532 x2 M3 x 8mm BHCS 91675 Caster Block 25215 M3 Locknut, black ! There are three caster block inserts included (0°, +/- 2.5 °, +/- 5 °). +5 ° is the standard insert used. Tab up = positive caster Tab down = negative caster You can install an optional #31520 screw to use as a steering stop setting.
PAGE 9
:: Bag 9-10 - Step 2 91692 Rear Gearbox Brace 91695 x2 Rear Arms 91670 Hinge Pin (rear, Inner) 91685 Rear Bumper 25204 x2 M3 x 16mm FHCS 91692 Arm Mount, D :: Bag 11-14 - Step 1 91465 x2 Gear Diff washer 91462 Gear Diff Gear 91605 CVA Axle Shim ! Install smaller gear Diff Washer before the larger washer.
PAGE 10
:: Bag 11-14 - Step 3 4675 x4 M2.
PAGE 11
:: Bag 11-14 - Step 6 9603 x2 Slipper Pad 91715 Lay-down Motor Plate 7485 x2 FT V2 Slipper Hub 25202 x3 M3 x 10mm FHCS ! There’s also a 72T 48P spur gear (#9649) included for stock motor use! 9652 78T 48P Spur Gear :: Bag 11-14 - Step 7 ! Set nut flush with top shaft.
PAGE 12
:: Bag 15-16 - Step 1 91563 10 x 15 x 4 Bearing 91697 Rear Hub Link Insert 25215 M3 Locknut, black Rear Hub Link Setting (Right Side Shown): 91698 Rear Hub Link Nut 89218 3 x 8mm Washer Up 91697 Rear Hub 91049 Heavy-duty Ballstud, 10mm th #1 re 59 ad 6 lo ck Build x2 (right and left side) 91697 Rear Hub Insert (+3) 91562 6 x 13 x 5 Bearing Down Insert A C B B A E D D C E 0/3 up 0/3 down 1/2 up 1/2 down Axle Height 0 (low) + 3mm + 1mm + 2mm Recommended Ballstud location :: Bag
PAGE 13
:: Bag 17 - Step 1 91722 Ball Cup Racers Tip: ! Orient the notch to the left throughout the car. It indicates which end has the left hand threads! Use black grease (#6588) on the threads of the turnbuckles for easier ball cup installation! 91723 Turnbuckle 3x48mm 91722 Ball Cup Steering Turnbuckle 28.75mm Build x2 (right and left side) :: Bag 17 - Step 2 91722 Ball Cup 91723 Turnbuckle 3x48mm 91722 Ball Cup Front Camber Turnbuckle 22.
PAGE 14
:: Bag 18-19 - Step 1 91533 x2 Shock Bushing, Short 25188 x2 M3 x 20mm BHCS 25203 x4 M3 x 12mm FHCS 91663 Front Shock Tower, Gull-Wing :: Bag 18-19 - Step 2 89204 x2 M3 x 24mm BHCS 91718 x2 Rear Wing Mount 91665 Rear Shock Tower 91720 x2 Shock Bushing, Long 89202 x4 M3 x 12mm BHCS 89202 x4 M3 x 12mm BHCS :: Bag 20-22 - Step 1 91634 12mm V2 Shock Piston (1.6 front) (1.7 rear) 91615 V2 3 x 21 Shock Shaft TiN (front) 91619 V2 3 x 27.
PAGE 15
:: Bag 20-22 - Step 2 91491 12mm Shock Cap O-Ring 91480 12x23mm V2 Shock Bodies (front) 91481 12x27.5mm V2 Shock Bodies (rear) ! ! Lightly rub shock oil on the o-ring before installation! 5 e 10 #1 slim n e e gr 91721 Shock Eyelet Front Shocks - Long Rear Shocks - Short 31327 VCS3 Shock Bottom Cap O-Ring 91493 x2 X-Ring Racers Tip: #11 0 en 5 slim e 91495 V2 Shock Spacer gre 91495 x2 V2 Shock Hat Bushing There is a short and long shock eyelet.
PAGE 16
:: Bag 20-22 - Step 5 ! 91447 Shock Bushing 25612 M3 Locknut w/Flange Use outside hole in front arm! 91447 Shock Bushing ! Use inside hole in rear arm! 25188 M3 x 20mm BHCS Build x2 (right and left side) 25612 M3 Locknut w/Flange 25187 M3 x 14mm BHCS :: Bag 23 - Step 1 Motor not included! ! See page 19 for gear mesh setting instructions! 89218 x2 3 x 8mm Washer 31532 x2 M3 x 8mm BHCS Pinion / Setscrew not included! :: Bag 24-26 - Step 1 25225 M3 x 3mm Set Screw ESC not included! Receiv
PAGE 17
:: Bag 24-26 - Step 2 91734 Battery Foam, B6 91730 x2 Battery Strap Shoulder Screw :: Bag 24-26 - Step 3 Front Battery not included! 1 2 3 4 5 ! F Make sure the battery strap shoulder screw is flush with the top of your battery pack! R :: Bag 24-26 - Step 4 89218 x2 3 x 8mm Washer 91731 Battery Strap, B6 25211 x2 M3 x 10mm BHCS 91731 x2 Battery Strap Nut, B6 91729 x2 Thumb Screw, B6
PAGE 18
:: Bag 24-26 - Step 5 25203 x2 M3 x 12mm FHCS 91718 Wing Button x2 91741 Wing, B6 Body Trimming / Mounting: There are 3 body trimming options depending on what transmission and shock position you choose to run. Cut Line A: Laydown Transmission / Rear Shocks mounted in rear of arm. Cut Line B: Laydown Transmission / Rear Shocks mounted in front of arm. Cut Line C: 3 Gear Stand Up Transmission.
PAGE 19
:: Painting Tips Your B6 Team Kit comes with a clear polycarbonate body. You will need to prep the body before you can paint it. Wash the INSIDE thoroughly with warm water and liquid detergent (do not use any detergents with scents or added hand lotion ingredients!). Dry the body using a clean, soft, lint-free cloth. Use the supplied window masks to cover the windows from the INSIDE of the body (RC cars get painted on the inside).
PAGE 20
:: Tuning Tips (cont.) Gear Box Type: Selecting the correct gear box is dependent on the type of track it will be used on. The optional 4 gear stand-up gear box is for the lowest grip conditions. This gear box moves the weight towards the rear of the car and also uses the rotation of the motor to transfer weight to the rear while on-power. The 3 gear stand-up gear box also moves the weight towards the rear of the car, but in this configuration, the motor’s rotation helps with on-power steering.
PAGE 21
:: Tuning Tips Ackermann: Ackermann is the angle difference between the front wheels when they are turned to steer the car. For minimal tire slip, it is standard for the inside wheel to steer to a greater angle than the outside wheel. The B6 allows Ackermann adjustments by changing the washer thickness used behind the steering rack ballstuds. The kit setup uses 2mm washers and is most common for racing conditions.
PAGE 22
:: Shocks 4187 31327 31510 89278 91304 91310 91449 91480 91481 91491 91492 91493 91495 91615 91619 91634 91721 :: Optional Ball Differential .030 Nylon Washer VCS3 Shock Bottom Cap and O-Ring 2x4mm BHCS 2.5mm Washer 12MM Threaded Collar and O-Ring 12MM Shock Spring Cups (+0mm, +5mm, +9mm) 12MM V2 Composite Shock Cap w/O-ring and bleeder screw 12x23MM V2 Shock Bodies 12x27.
PAGE 23
:: Transmission 25187 25202 31286 31532 89203 89218 91048 91132 91560 91563 91692 91693 91708 91709 91710 91715 91716 M3 x 14mm BHCS M3 x 10mm FHCS Ball Stud Washers, Alum. (1mm, 2mm) M3 x 8mm BHCS M3 x 16mm BHCS 3 x 8mm Washer Heavy-duty Ballstud, 8mm FT 4x4 Idler Gear Shaft FT Bearings, 5x10x4mm FT Bearings, 10x15x4mm Rear Gearbox Brace, B6 Rear Ball Stud Mount, B6 Lay Down Gear Box Chassis Brace, B6 Top Shaft, B6 Lay Down Motor Plate, B6 Idler Gear, 39T 20 20 4 ea. 6 10 10 8 2 4 4 1 1 Pr.
PAGE 24
:: Gear Differential 4675 9831 91462 91463 91464 91465 91605 91703 5450 5451 5452 5444 5453 5446 5454 5455 5466 5456 5457 5458 5448 5459 5461 5463 5465 M2.
PAGE 25
:: Front Arm 25187 25188 25215 31286 31510 31531 31532 91047 91049 91560 91670 91673 91675 91676 91677 91679 91682 91738 M3 x 14mm BHCS M3 x 20mm BHCS M3 Locknut, Black FT Ballstud Washer, aluminum (1mm, 2mm) M2 x 4mm BHCS M3 x 6mm, BHCS M3 x 8mm, BHCS Heavy-duty Ballstud, 6mm Heavy-duty Ballstud, 10mm FT Bearing, 5 x 10 x 4 Hinge Pin Set, B6 Front Arm, Gull-Wing, B6 Caster Block, B6 Caster Hat Bushing, B6 (0mm, 1mm, 2mm, 3mm) Steering Block, B6 Steering Block Arm, B6 Front Axle, B6 M4 Serrated Nut w/ F
PAGE 26
:: Front Shock Tower 25188 25203 25612 91447 91533 91663 M3 x 20mm BHCS M3 x 12mm FHCS M3 Locknuts w/Flange Shock Bushing Balls Shock Bushings, Short w/Balls Front Tower, Gull-Wing, B6 20 20 20 4 4 ea.
PAGE 27
:: Front Bulkhead / Steering 25188 25204 25225 31283 31286 89202 91048 91049 91475 91654 91655 91656 91667 91685 M3 x 20mm BHCS M3 x 16mm FHCS M3 x 3mm Set Screw Ball Studs, Long, 5mm FT Ball Stud Washer, aluminum (1mm, 2mm) M3 x 12mm BHCS Heavy-duty Ballstud, 8mm Heavy-duty Ballstud, 10mm 3x7x3 Ball Bearing Top Plate, B6 Front Ball Stud Mount, B6 Bulkhead, B6 Steering Assembly, B6 Bumpers, B6 20 20 20 6 4 ea. 25188 91667 10 8 8 8 1 1 1 1 1 ea.
PAGE 28
:: Body and Decals :: Factory Team and Option Parts 7495 31286 91175 91176 91177 91178 91179 91389 91447 91450 91492 91495 91548 91549 91550 91553 91580 91581 91582 91583 91584 91585 91588 91589 91592 91593 91594 91595 91596 91597 91609 91612 91658 91659 91663 91668 91669 91672 91673 91674 91683 91687 91688 91696 91703 91707 91708 91711 91714 91715 91716 91735 91736 91745 91746 91747 91748 91749 91750 91751 91752 91753 91755 Vented V2 Slipper Hubs FT Ballstud Washer, aluminum (1mm, 2mm) FT VTS Slipper
PAGE 29
:: Reedy Motors / Spare Parts / Accessories 252 253 254 255 256 257 258 259 260 261 262 263 264 265 266 267 268 269 270 284 285 Sonic Sonic Sonic Sonic Sonic Sonic Sonic Sonic Sonic Sonic Sonic Sonic Sonic Sonic Sonic Sonic Sonic Sonic Sonic Sonic Sonic 540-M3 540-M3 540-M3 540-M3 540-M3 540-M3 540-M3 540-M3 540-M3 540-M3 540-M3 540-M3 540-M3 540-M3 540-M3 540-M3 540-M3 540-M3 540-M3 540-M3 540-M3 25.5 21.5 17.5 13.5 10.5 9.5 8.5 8.0 7.5 7.0 6.5 6.0 5.5 5.0 4.5 4.0 3.5 SS 17.5 SS 13.5 SS 21.5 SS 10.
PAGE 30
:: Tools 1111 1113 1449 1541 1545 1546 1554 1564 1567 1568 1569 1570 1590 1592 1655 1656 1657 1658 1659 1660 1661 1662 1663 1664 1665 1666 1667 1668 1669 1670 1671 1672 1673 1674 1675 1719 1737 3718 3719 3720 3987 6429 6956 7709 :: RePlay Cameras / Kicker Audio FT Turnbuckle Wrench 12mm Big Bore Shock Tool FT Off Road Ride Height Gauge FT Hex Driver Set, (7 pcs) FT 5/64” Blue Hex Driver FT 3/32” Gold Hex Driver FT Silver Spring Hook Tool FT 5.5mm Red Nut Driver FT 8mm Gold Nut Driver Factory Team 5.
PAGE 31
:: Notes :: Contact Information Check out the following web sites for all of our electric kits, current products, new releases, setup help, tips, and racing info! Associated Electrics, Inc. 26021 Commercentre Drive Lake Forest, CA 92630-8853 USA http://www.TeamAssociated.com http://www.RC10.com http://twitter/Team Associated http://bit.
PAGE 32
Team Kit Stock Setup Driver: Date: Track: Qualify: Front Suspension: 19mm Ride Height: -1° Camber: Toe: 0° Arm Type: Gull-Wing Tower Type: Gull-Wing +5° Caster Block Insert: Plastic Bulkhead Type: Kick-Up Angle: Wheel Hex: 25° 5.0mm Event: TQ: Anti Roll Bar: Main: Finish: 0mm Bump Steer Spacing: None White (0.8mm) Gray (0.9mm) Blue (1.
PAGE 33
Driver: Event: Date: Track: Qualify: TQ: Main: Finish: Best Lap Time: Front Suspension: Anti Roll Bar: Ride Height: Camber: Toe: Arm Type: Tower Type: Axle Height: Bump Steer Spacing: None White (0.8mm) Gray (0.9mm) Blue (1.
PAGE 34
Associated Electrics, Inc. 26021 Commercentre Dr. Lake Forest, CA 92630 USA http://www.TeamAssociated.com http://www.RC10.com http://twitter/Team_Associated http://bit.ly/AEonFacebook call: (949) 544-7500 - fax: (949) 544-7501 Check out the following web sites for all of our kits, current products, new releases, setup help, tips, and racing info! www.TeamAssociated.com. - www.RC10.