Datasheet

ManualsBrandsTE Connectivity ManualsConnector ToolsExtraction Tool for PLCC and SOJ Packages

*Trademark

TE Connectivity, TE connectivity (logo), and TE (logo) are trademarks. Other logos, product and/or company names may be trademarks of their respective owners.

1 of 2

Instruction Sheet

TOOLING ASSISTANCE CENTER

1-800-722-1111

PRODUCT INFORMATION

1-800-522-6752

This controlled document is subject to change.

For latest revision and Regional Customer Service,

visit our website at www.te.com

408-9695

Plastic Leaded Chip Carrier (PLCC)

Extraction Tool 822154-1

18 OCT 13 Rev D

•7.62 mm [.300 in.] centerlines

••10.16 mm [.400 in.] centerlines

•••10.16 mm [.400 In.] centerlines, 0.8 mm pitch

Figure 1

1. INTRODUCTION

This instruction sheet covers the use of Extraction Tool

822154-1. This tool is designed to remove chip

carriers from the TE Connectivity surface mount low

insertion force sockets, SOJ (Small Outline J-Leaded)

sockets, and solder tail sockets listed in Figure 1.

NOTE

Dimensions are in millimeters [with inch equivalents in

brackets]. Figures and illustrations are for reference only

and are not drawn to scale.

Reasons for reissue of this sheet are provided in

Section 5, REVISION SUMMARY.

2. DESCRIPTION

This tool is contoured for insertion into either of the

two extraction cavities on the socket. By inserting the

extraction tool with the correct angle (see Figure 2),

and pivoting the tool on its heel against the socket, the

chip carrier is easily removed.

3. EXTRACTION PROCEDURE

1. Orient the socket and tool as shown in Figure 3.

2. Insert the extraction tool into the socket so that

the front angle of the tool is perpendicular to the

chip carrier.

Extraction Slot

C hi p

Carrier

(Ref)

Socket

(Ref)

Hooked

Tip

Extraction Tool

822154-1

SOCKET TYPE AND

NO. OF POSITIONS

SOLDERTAIL SOCKET

PART NUMBER

WITHOUT POST

LOW INSERTION FORCE SOCKET PART NUMBER

WITH POST WITHOUT POST TAPE

PLCC 20 --- 822270-1 822269-1 3-822269-1

PLCC 28 822437-1 822272-1 822271-1 3-822271-1

PLCC 32 822437-2 822274-1 822273-1 3-822273-1

PLCC 44 822437-3 822276-1 822275-1 3-822275-1

PLCC 52 822437-4 822278-1 822277-1 3-822277-1

PLCC 68 822437-5 822280-1 822279-1 3-822279-1

PLCC 84 822437-6 822282-1 822281-1 3-822281-1

SOJ 28• --- --- 822372-1 3-822372-1

SOJ 28•• --- 822363-1 822361-1 3-822361-1

SOJ 32• --- --- 822374-1 3-822374-1

SOJ 32•• --- 822364-1 822362-1 3-822362-1

SOJ 40•• --- 822267-2 822265-2 3-822265-2

SOJ 42•• --- --- 822378-1 3-822378-1

SOJ 44•• --- --- 822393-1 3-822393-1

SOJ 50••• --- --- 822405-1 3-822405-1

NOTE

Summary of content (2 pages)

PAGE 1
Instruction Sheet 408-9695 Plastic Leaded Chip Carrier (PLCC) Extraction Tool 822154-1 18 OCT 13 Rev D Extraction Slot Hooked Tip Extraction Tool 822154-1 Chip Carrier (Ref) Socket (Ref) SOCKET TYPE AND NO.
PAGE 2
408-9695 CAUTION Insertion of the extraction tool with an incorrect angle will result in damage to the socket. This incorrect angle will bottom under the stand-off rather than the bottom of the chip carrier. ! 4. TOOL INSPECTION 3. Lower extraction tool into extraction cavity until it bottoms. Extraction Tool 822154-1 has been inspected and should be verified with the information provided in Figure 4.