Datasheet

408- 10040
5 of 7Rev E
Su
g
g
e
s
ted
P
l
u
g
G
a
g
e
D
e
s
i
g
n
fo
r
Wire Barrel Section of Crimping Chamber
Die Closure
Configuration
GO Dim. NO--GO Dim.
50.8 [2]
Min Typ
GO
NO
GO
6.35 [.250]
Min Typ
Die Closure
Configuration
GO Dim. NO--GO Dim.
“W”
Su
g
g
e
s
ted
P
l
u
g
G
a
g
e
D
e
s
i
g
n
fo
r
Insulation Barrel Section of Crimping Chamber
“W”
HAND
WIRE BARREL CRIMP CHAMBER INSULATION BARREL CRIMP CHAMBER
H
A
N
D
TOOL
GO NO--GO GO NO--GO WIDTH (W)
576778 2.591--2.598 [.1020--.1023] 2.690--2.692 [.1059--.1060] 0.813--0.820 [.0320--.0323] 1.217--1.219 [.0479--.0480] 4.06 [.160]
576779 2.591--2.598 [.1020--.1023] 2.690--2.692 [.1059--.1060] 1.067--1.074 [.0420--.0423] 1.471--1.473 [.0579--.0580] 4.39 [.173]
576780 3.048--3.056 [.1200--.1203] 3.147--3.150 [.1239--.1240] 0.940--0.947 [.0370--.0373] 1.344--1.346 [.0529--.0530] 5.89 [.232]
576781 3.124--3.132 [.1230--.1233] 3.223--3.226 [.1269--.1270] 0.940--0.947 [.0370--.0373] 1.344--1.346 [.0529--.0530] 5.89 [.232]
576782 3.327--3.335 [.1310--.1313] 3.426--3.429 [.1349--.1350] 1.067--1.074 [.0420--.0423] 1.471--1.473 [.0579--.0580] 6.63 [.261]
576783 3.683--3.691 [.1450--.1453] 3.782--3.785 [.1489--.1490] 1.067--1.074 [.0420--.0423] 1.471--1.473 [.0579--.0580] 6.63 [.261]
576784 4.775--4.783 [.1880--.1883] 4.874--4.877 [.1919--.1920] 1.676--1.684 [.0660--.0663] 2.080--2.083 [.0819--.0820] 8.43 [.332]
Figure 5
Figure 6
(Detail A) Inspection of Wire Barrel Crimping Dies (Detail B) Inspection of Insulation Crimping Dies
GO gage must pass completely
through the die closure.
NO--GO gage may enter par tially,
but must not pass completely
through the die closure.
Wire Barrel Dies
Bottomed But Not
Under Pr essure
Gage
Insert 0.025 mm
[.001 In.] Shim Here
When Checking
CERTI--CRIMP Hand
Crimping Tool Ratchet
Control
Gage
Adjustment Pin
in No. 1
Position
Wire Barrel Dies
Bottomed But
Not Under Pressure