TDK.l25.03/52x USB veloCD 3/5/03 2:17 PM Page 1 HIGH SPEED USB 2.
TDK.l25.03/52x USB veloCD 5/6/03 11:29 AM Page 2 WARNING: PRIOR TO PLACING ANY DISC IN THIS DRIVE, CAREFULLY INSPECT IT TO ENSURE THAT IT IS NOT CRACKED, DEEPLY SCRATCHED OR OTHERWISE DAMAGED IN ANY WAY. USE OF A CRACKED, DEEPLY SCRATCHED OR DAMAGED DISC IN THIS OR ANY OTHER HIGH-SPEED DRIVE MAY CAUSE THE DISC TO SHATTER AND RESULT IN DAMAGE NOT ONLY TO THE DISC BUT TO THE DRIVE AS WELL.
TDK.l25.03/52x USB veloCD 3/5/03 2:17 PM Page 3 HIGH-SPEED USB 2.0 EXTERNAL CD-RW DRIVE SUPPLIED WITH: veloCD Drive USB 2.0 Cable (A-B) PC Software AC/DC Adapter Drive Stand Emergency Ejector Pin Manual Quickstart Guide MINIMUM SYSTEM REQUIREMENTS: Windows: Pentium III 333 MHz or higher Windows 98SE/ME/2000/XP 64 MB RAM • NOTES: When connected to the computer via a standard USB 1.1 port, the drive's maximum write speed is 4X due to bandwidth limitations. Connect to the computer via USB 2.
TDK.l25.03/52x USB veloCD 3/5/03 2:03 PM Page 4 PLUG AND PLAY 5. Connect the other end of the USB cable to the back of your veloCD drive. EASY TO SET-UP AND USE 1.Insert the program installation CD into your computer’s original disc drive. 2.Install the TDK CD Blender Software Suite by clicking on the desired programs. Follow the on-screen prompts to finish installation. 3.Locate the USB 2.0 port on your PC. 4.Connect the flat end of the USB cable to the PC’s USB 2.O port. 6.
TDK.l25.03/52x USB veloCD 3/5/03 2:17 PM Page 6 INSTALLING THE HI SPEED DRIVER (WINDOWS 98SE AND WINDOWS ME) NOTE: The high speed USB driver is not required for Windows 2000 & XP installation. NOTE: You cannot use your new veloCD drive to install the high speed USB driver. Use your existing CD-ROM drive to install the high speed USB driver. NOTE: During the high-speed USB driver installation process, you may be asked to insert the Windows installation disc. To install the high speed USB driver: 1.
TDK.l25.03/52x USB veloCD 3/5/03 2:17 PM Page 7 TROUBLESHOOTING veloCD will not record at maximum speed. Verify that the drive is connected to a USB 2.0 port. If the drive is connected to a USB 1.1 port, recording will be limited to 4x maximum speed. Ensure that DMA is enabled (Windows 98SE/ME) 1. In Windows, click the START button, then SETTINGS, then CONTROL PANEL. 2. Double click SYSTEM in the Control Panel folder, then select the DEVICE MANAGER tab. You will see a list of devices in your system. 3.
TDK.l25.03/52x USB veloCD 3/5/03 2:17 PM Page 8 TROUBLESHOOTING (continued) Can’t create a CD using CD-R or CD-RW media. Can’t hear an audio CD through the veloCD headphone jack. Can’t read a session after a successful write. 1. A buffer underrun occurred. Either select a slower speed or enable Buffer Underrun Protection in your software. 2. Disable all other functions and applications that could interrupt the stream of information. 3.
TDK.l25.03/52x USB veloCD 3/5/03 2:17 PM Page 9 TROUBLESHOOTING (continued) The veloCD drive is not recognized by the operating system. The disc keeps ejecting. Can’t load the disc. The drive fails to read the disc. 1. Make sure the USB cable is fully connected at both ends. 2. Verify that the drive is properly connected to the computer using a working USB cable. 3. Make sure the USB driver included in the Bonus Utilities folder on the CD Blender Recording Software Suite program disc is installed.
TDK.l25.03/52x USB veloCD 3/5/03 2:17 PM Page 10 TDK LIMITED WARRANTY One Year Limited Warranty for Hardware TDK Electronics Corporation ("TDK") warrants to the end-user customer that this data storage product, exclusive of software (referred to herein as "Hardware" or "Product") will be free from defects in material and workmanship for a period of one (1) year from date of purchase.
TDK.l25.
TDK.l25.