Datasheet

DENSEI-LAMBD
A
PA578-01-01A
ITEMS
1 Nominal Output Voltage V 5 12 24
2 Maximum Output Current ( Peak Output Current ) ( * 1 ) A 200 88 44 ( 51 )
3 Maximum Output Power ( Peak Output Power ) ( * 1 ) W 1000 1056 1056 ( 1224 )
4 Efficiency (Typ) (115/230VAC) ( * 2 ) % 79 / 81 82 / 84 84 / 86
5 Input Voltage Range ( * 3 )
-
6 Input Current (Typ) (115/230VAC) ( * 2 ) A
7 Inrush Current (Typ) ( * 4 )
-
8 PFHC
-
9 Power Factor (Typ) (115/230VAC) ( * 2 )
-
10 Output Voltage Range V 4.0-6.0 9.6-14.4 19.2-28.8
11 0≤Ta≤74°C mV 120 150 150
-20≤Ta<0°C mV 160 180 180
12 Line Regulation ( * 6, 7 ) mV 20 48 96
13 Load Regulation ( * 6, 8 ) mV 30 72 144
14 Temperature Coefficient
-
15 Over Current Protection ( * 9 ) A 210 <
92.4 < 51.6 <
16 Over Voltage Protection ( * 10 ) V 6.25-7.25 15.0-17.4 30.0-34.8
17 Hold-Up Time (Typ) (115/230VAC) ( * 2 )
-
18 Leakage current (Typ) ( * 11 )
-
19 Remote Sensing
-
20 Remote ON/OFF control
-
21 Monitoring Signal
-
22 Parallel Operation
-
23 Series Operation
-
24 Operating Temperature ( * 12 )
-
25 Operating Humidity
-
26 Storage Temperature
-
27 Storage Humidity
-
28 Cooling
-
29 Withstand Voltage
-
30 Isolation Resistance
-
31 Vibration ( * 13 )
-
32 Shock (In package)
-
33 Safety ( * 14 )
-
34 Line Dip
-
35 EMI
-
36 Immunity
-
37 Weight (Typ)
-
38 Dimension (W x H x D) mm
* Read instruction manual carefully , before using the power supply unit.
= NOTES=
* 1: ( ): Peak Output Current is possible at 170-265VAC input range , operating period at Peak Output Current is less than 10sec, duty less than 35% .
Average output power and current is less than Maximum Output Power and Maximum Output Current.
* 2 : At Maximum Output Power, nominal input voltage, Ta = 25°C.
* 3 : For cases where conformance to various safety specs ( UL, CSA, EN ) are required, to be described as 100 - 240VAC, 50 / 60Hz on name plate.
* 4 : First/second inrush current, not applicable for the in-rush current to Noise Filter for less than 0.2ms.
* 5 : Please refer to Fig. A for measurement point of ripple and noise.
Ripple & noise are measured at 20MHz by using a twisted pair of load wires terminated with a 0.1uF and 47uF capacitor.
* 6 : Measure line & load regulation at output terminal M4 tapped point.
* 7 : 85 - 265VAC, constant load.
* 8 : No load - Full load (Maximum power ), constant input voltage.
* 9 : Constant current limit with automatic recovery.
Avoid to operate at overload or dead short for more than 30 seconds.
* 10: OVP circuit will shutdown output, manual reset (Remote ON/OFF control reset or Re-power on).
* 11: Measured by each measuring method of UL, CSA, EN and DENAN (at 60Hz), Ta=25°C.
Worst case: < 0.3mA at 264VAC, 63Hz (Normal Condition); < 0.5mA (Single Fault Condition)
* 12: Refer to Output Derating Curve (PA578-01-02_ ) for details of output derating versus ambient temperature.
- Load (%) is percent of Maximum Output Power and Maximum Output Current (Item 2 and 3).
Do not exceed derating of Maximum Output Power and Maximum Output Current.
- 100% load start up at -40°C is possible. However, it may not fulfil all the specifications.
* 13: Category 4 exposure levels: Trunk transportation over U.S. highways, Composite two-wheeled trailer.
* 14: As for DENAN, designed to meet at 100VAC.
Less than 0.02%/°C
20ms
SWS1000L SPECIFICATIONS
SWS1000L-5 SWS1000L-24SWS1000L-12
0.1mA at 115VAC, 60Hz / 0.2mA at 230VAC, 60Hz
Possible
Possible
ALM ( Open Collector Output )
Ripple and Noise (115/230VAC)
( * 5 )
85 - 265VAC (47-63Hz) or 120 - 350VDC
12 / 6
20A/40A at 115VAC, 40A/40A at 230VAC, Ta=25°C (first inrush/second inrush)
Designed to meet IEC61000-3-2
0.98 / 0.95
Possible
Possible
- 20 to + 74 °C (-20°C to +50°C: 100%, +74°C: 50%)
100% load start up at -40°C
20 to 90 %RH (No dewdrop)
- 40 to +85°C
10 to 95%RH (No dewdrop)
Forced air by build-in fan
Input - Output : 4.0kVAC (20mA), Input - FG : 2.0kVAC (20mA)
Output - FG : 500VAC (100mA), Output - CNT/ALM/AUX : 100VAC (100mA) for 1min.
Input - FG, Input - Output and Output - FG: More than 50MΩ (500VDC)
Output - CNT/ALM/AUX: More than 50MΩ (100VDC) at Ta=25°C and 70%RH
Designed to meet MIL-STD-810F 514.5 Category 4, 10
Designed to meet MIL-STD-810F 516.5 Procedure I,VI
Approved by UL60950-1, CSA60950-1, EN60950-1, EN50178,
UL60601-1, EN60601-1, CSA-C22.2 No.601.1-M90
-5 (Level 3,4), -6 (Level 3), -8 (Level 4), -11
2.3kg
150 x 61 x 240 (Refer to Outline Drawing)
Designed to meet DENAN, EN61010-1.
Designed to meet SEMI-F47 (200VAC line only)
Designed to meet VCCI-B, FCC-B, EN55011/EN55022-B
Designed to meet EN61000-4-2 (Level 2,3), -3 (Level 3), -4 (Level 3),
MODEL
+
Measurement point for Ripple and Noise.
Output Terminal
A
+V
-V
47µ 0.1µ
150m
m
Fig. A