TM GENESYS GEN 5kW SERIES POWER SUPPLIES USER MANUAL This Manual Covers Models: GEN8-600 GEN20-250 GEN60-85 GEN150-34 GEN10-500 GEN30-170 GEN80-65 GEN300-17 GEN16-310 GEN40-125 GEN100-50 GEN600-8.
This page intentionaly left blank
DECLARATION OF CONFORMITY We, Nemic-Lambda Ltd., declare under our sole responsibility that the product: Product name: Programmable Regulated Power Supplies, Genesys Models: GEN5000W Three phase 190-240Vac GEN5000W Three phase 380-415Vac TM series with rated output from 8VDC/600A up to 600VDC/8.5A and total output power equal to or less than 5100W conforms to the following specifications: Safety: IEC60950-1:2001, EN 60950-1:2001.
This page intentionaly left blank
TABLE OF CONTENTS WARRANTY ..........................................................................................................................................Pg.1 REGULATORY NOTICES .................................................................................................................... Pg.2 SAFETY INSTRUCTIONS..................................................................................................................... Pg.3 GERMAN SAFETY INSTRUCTIONS ................................
TABLE OF CONTENTS 3.9 CONNECTING THE LOAD .......................................................................................................... Pg.19 3.9.1 Load Wiring .......................................................................................................................... Pg.19 3.9.2 Current Carrying Capacity ................................................................................................... Pg.19 3.9.3 Wire termination .................................................
TABLE OF CONTENTS CHAPTER 6 REMOTE ANALOG PROGRAMMING ................................................................. Pg.45 6.1 INTRODUCTION ........................................................................................................................... Pg.45 6.2 LOCAL/REMOTE ANALOG CONTROLL....................................................................................... Pg.45 6.3 LOCAL/REMOTE ANALOG INDICATION...............................................................................
This page intentionaly left blank
WARRANTY This Nemic-Lambda product is warranted against defects in materials and workmanship for a period of five years from date of shipment .During the warranty period, Nemic-Lambda will, at it’s option, either repair or replace products which prove to be defective. LIMITATION OF WARRANTY The warranty shall not apply to defects resulting from improper or inadequate usage or maintenance by the buyer, buyer supplied products or interfacing.
REGULATORY NOTICES FCC Notice This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules.
SAFETY INSTRUCTIONS CAUTION The following safety precaution must be observed during all phases of operation, service and repair of this equipment. Failure to comply with the safety precautions or warnings in this document violates safety standards of design, manufacture and intended use of this equipment and may impair the built-in protections within. Nemic-Lambda shall not be liable for user’s failure to comply with these requirements.
SAFETY INSTRUCTIONS. ENVIRONMENTAL CONDITIONS The GenesysTM power supply series safety approval applies to the following operating conditions: *Indoor use *Ambient temperature: 0oC to 50oC *Maximum relative humidity: 90% (no condensation) *Altitude: up to 3000m *Pollution degree 2 CAUTION Do not use this product in environments with strong Electromagnetic field, corrosive gas and conductive materials. On (Supply) CAUTION Risk of Electrical Shock. ! Instruction manual symbol.
SICHERHEITS-INSTALLATIONS ANWEISUNGEN Vorsicht Vor Anschluss an das Netz ist die Aufstellanleitung wie nachstehend beschrieben zu beachten. Die nachstehenden Sicherheitsanweisungen müssen während aller Phasen des Betriebes, des Services und der Reparatur dieser Ausrüstung beachtet werden. Alle notwendigen Bedingungen die sicherstellen, dass die Einrichtung zu keiner Gefahr im Sinne dieser Norm führen kann, sind in diesem Handbuch beschrieben.
Spannungsfuhrende Teile Die Geräteabdeckung darf nur im stromlosen Zustand geöffnet werden. Interne Modifikationen, sowie Bauteileaustausch ist nur durch Nemic-Lambda qualifiziertes Personal erlaubt. Vor Austausch von Bauteilen ist das Netzkabel bzw. die Versorgungsspannung zu trennen. Energieversorgungsanschlüsse sind immer zu trennen um Personenverletzungen durch gefährliche Energieinhalte und Spannungen auszuschliessen.
CHAPTER 1 GENERAL INFORMATION 1.1 USER MANUAL CONTENT This user’s manual contains the operating instructions, installation instructions and specifications of TM the Genesys 5000W power supply series. The instructions refer to the standard power supplies, including the built-in RS232/485 serial communication. For information related to operation with the optional IEEE programming, refer to User Manual for Power Supply IEEE Programming Interface. 1.2 INTRODUCTION 1.2.
* Parallel operation (Master/Slave) with Active current sharing. * Remote sensing to compensate for voltage drop of power leads. * External Analog Programming and Monitoring standard (0-5V or 0-10V, user selectable). * Cooling fan speed control for low noise and extended fan life. * Zero stacking- no ventillation holes at the top and bottom surface of the power supply. * Optional GPIB interface (SCPI compatible). * Optional Isolated Analog programming/monitoring (0-5V or 0-10V, user selectable and 4-20mA).
1.2.9 Cooling and mechanical construction TM The Genesys series is cooled by internal fans. At the installation, care must be taken to allow free air flow into the power supply via the front panel and out of the power supply via TM the rear panel. The Genesys power supplies have a compact and lightweight package which allows easy installation and space saving in the application equipment. CAUTION Observe all torque guidelines within this manual. Over torqueing may damage unit or accessories.
CHAPTER 2 SPECIFICATIONS 2.1 OUTPUT RATING MODEL 1.Rated output voltage(1*) 2.Rated output current (*2) 3.Rated output power 2.2 INPUT CHARACTERISTICS GEN V A W V 1.Input voltage/freg. (*3) 8-600 8 600 4800 10-500 10 500 5000 16-310 16 310 4960 8 10 16 40-125 40 125 5000 60-85 60 85 5100 80-65 80 65 5200 40 60 80 100 150 300 600 22 22 22 22 22 22 22 22 11 10.5 11 11 11 0.94 @200/380Vac, rated output power.
2.6 PROGRAMMING AND READBACK (RS232/485, Optional LAN/IEEE Interface) 1.Vout programming accuracy 2.Iout programming accuracy (*13) 3.Vout programming resolution 4.Iout programming resolution 5.Vout readback accuracy 6.Iout readback accuracy (*13) 7.Vout readback resolution 8.Iout readback resolution ----------------- 2.7 PROTECTIVE FUNCTIONS V --- 1.Foldback protection 2.Over-voltage protection (OVP) 3.Over-voltage trip point 4.Output under voltage limit (UVL) 5.
NOTES: *1: Minimum voltage is guaranteed to maximum 0.2% of the rated output voltage. *2: Minimum current is guaranteed to maximum 0.4% of the rated output current. *3: For cases where conformance to various safety standards (UL, IEC etc.) is required, to be described as 190~240Vac (50/60Hz) for 3-Phase 200V models, and 380~415Vac (50/60Hz) for 3-Phase 400V models. *4: 3-Phase 200V models: at 200Vac input voltage. 3-Phase 400V: at 380Vac input voltage. With rated output power.
TM 88.0mm�0.3 2.13 GENESYS 5000W POWER SUPPLIES OUTLINE DRAWINGS TDI -Lambda 482.0�1.0mm 39.0�0.3mm 423.0�1.0mm Note 1 Note 4 Note 2 Note 5 L�1.0mm (See Table 1) A 86+/-0.3 Note 3 A 42.0 A 60.5 92.0 92.0 Table 1 442.5�1.0mm Dimension / Model m .0m /-2 4+ 10 L 8V-10V 16V-100V 517.5mm 497.5mm Bus-Bar Detail 16V to 100V Models 5.0mm 40.0 mm 30.0mm TD I -L am bd a 10.5mm 50.0mm Bus-Bar Detail 8V to 10V Models NOTES: 1.Analog programming connector.
CHAPTER 3 INSTALLATION 3.1 GENERAL This chapter contains instructions for initial inspection, preparation for use and repackaging for shipment. Connection to PC, setting the communication port and linking GenesysTM power supplies are described in Chapter 7. WARNING TM The Genesys series is intended only for installation in Restricted Access Location (RAL). Access to Hazardous parts (rear side of the power supply) shall be prevented after installation.
3.4.2 Rack Mount Slides (optional): CAUTION Ensure that the screws used to attach the slides to the unit do not penetrate more than 6mm into the sides of the unit. Use rack mount slides: General Devices P/N: CC3001-00-S160 (ordering P/N: C-300-S-116-RHLH) or equivalent to install the unit in a standard 19” equipment rack. Refer to Fig. 3-1 for slides assembly instructions. Use three #10-32x0.38"(max.) screws at each side. To prevent internal damage, use the specified screw length only. Fig.
WARNING Some components inside the power supply are at AC voltage even when the On/Off switch is in the “Off ” position. To avoid electric shock hazard, disconnect the line cord and load and wait two minutes before removing cover. The power supply ON/OFF switch is not the main disconnect device and does not completely disconnect all the circuits from the AC source. An appropiately rated disconnect device such as circuit breaker, type B plug on power cord, ...etc.
4.Connect the AC wires to the terminals of the input plug supplied with the unit. To connect the wires, loosen the terminal screw, insert the stripped wire into the terminal and tighten the screw securely (10.7-13.4 Lb-inch.). Refer to Fig. 3-3 for details. Pay attention to connect the wires according to the polarity marking on the plug. AC Input Plug : 3-Phase: P/N: PC6/4-STF-10,16: Wire clamp screws tightening torque: 10.7- 13.4 Lb-inch. Fig.3-3 AC Input plug t Protective Ground wire AC Line wires 5.
2. Connect the unit to an AC source as described in section 3.7. 3. Connect a DVM with appropriate cables for the rated voltage to the output terminals. 4. Turn the front panel AC power switch to On. 3.8.3 Constant Voltage Check 1. Turn on the output by pressing OUT pushbutton so the OUT LED illuminates. 2. Observe the power supply VOLT display and rotate the Voltage encoder. Ensure that the output voltage varies while the VOLT encoder is rotated.
3.8.7 Foldback Check WARNING Shorting the output may expose the user to hazardous voltages. Observe proper safety procedures. Refer to Section 5.5 for explanation of the FOLD function prior to performing the procedure below. 1. Ensure that the output voltage is set to approx. 10% of the unit rating. 2. Adjust the CURRENT encoder to set the current limit to approx. 10% of the unit rating. 3. Momentarily press the FOLD button. Ensure that the FOLD LED illuminates. The output voltage remains unchanged. 4.
2. Wire size should be selected to enable voltage drop per lead to be less than 1.0V at the rated current. Although units will compensate for up to 5V in each load wire, it is recommended to minimize the voltage drop (1V typical maximum) to prevent excessive output power consumption from the power supply and poor dynamic response to load changes. Please refer to Tables 3-2 and 3-3 for maximum wire length to limit voltage drop in American and European dimensions respectively.
3.9.4 Noise and Impedance Effects To minimize the noise pickup or radiation, the load wires and remote sense wires should be twistedpairs to the shortest possible length. Shielding of sense leads may be necessary in high noise environments. Where shielding is used, connect the shield to the chassis via a rear panel Ground screw. Even if noise is not a concern, the load and remote sense wires should be twisted-pairs to reduce coupling, which might impact the stability of power supply.
Wire terminal lug (2 places) M10x25 screw (2 places) Flat washer (2 places) Flat washer (2 places) Spring washer (2 places) Hex Nut (2 places) Screws tightening torque: 290-310 Lb-inch. Fig. 3-6: Load wires connection , 8V to 100V models. Shield Fig. 3-7: Bus-bars shield mounting 150V to 600V Models WARNING Hazardous voltages exist at the outputs and the load connections.
The 150V to 600V models have a four terminal wire clamp output connector. The two left terminals are the positive outputs and the other two right terminals are the negative outputs. Max. 30A per terminal. The connector requirements are as follows: 1. Wires: AWG18 to AWG10. 2. Tightening torque: 4.4-5.3Lb-inch. (0.5-0.6Nm). Follow the below instructions for connection of the load wires to the power supply: 1. Strip approx.10mm at the end of each of the wires. 2. Loosen the connector terminal screws. 3.
3.9.7 Connecting single loads, local sensing (default). Fig.3-11 shows recommended load and sensing connections for a single load. The local sense lines shown are default connections at the rear panel J2 sense connector. Local sensing is suitable for applications where load regulation is less critical. +V + Load Power Supply - -V - Rem.sense -Local sense Load lines, twisted pair, shortest length possible. +Local sense +Rem.sense Fig.3-11: Single load connection, local sensing 3.9.
Load lines, twisted pair, shortest length possible. +V Power Supply + Load#1 - -V + Load#2 - - Rem.sense -Local sense + Load#3 - +Local sense +Rem.sense Fig.3-13: Multiple loads connection, radial distribution, local sense 3.9.10 Multiple load connection with distribution terminals If remotely located output distribution terminals are used, the power supply output terminals should be connected to the distribution terminals by a pair of twisted and/or shielded wires.
WARNING OUTPUT TERMINAL GROUNDING There is a potential shock hazard at the RS232/485 and the IEEE ports when using power supplies with rated or combined voltage greater than 400V with the Positive Output of the power supplies is grounded. Do not connect the Positive Output to ground when using the RS232/485 or IEEE under the above conditions. 3.10 LOCAL AND REMOTE SENSING The rear panel J2 sense connector is used to configure the power supply for local or remote sensing of the output voltage. Refer to Fig.
3.10.3 Remote sensing WARNING There is a potential shock hazard at the sense point when using power supply with a rated output voltage greater than 40V. Ensure that the connections at the load end are shielded to prevent accidental contact with hazardous voltages. CAUTION When using shielded sense wires, ground the shield in one place only. The location can be the power supply chassis or one of the output terminals. Use remote sense where the load regulation at the load end is critical.
CHAPTER 4 FRONT AND REAR PANEL CONTROLS AND CONNECTORS 4.1 INTRODUCTION TM The Genesys Power Supply series has a full set of controls, indicators and connectors that allow the user to easily setup and operate the unit. Before starting to operate the unit, please read the following sections for explanation of the functions of the controls and connectors terminals. - Section 4.2: Front panel controls and indicators. - Section 4.3: Rear panel controls and connectors. 4.
Table 4-1: Front Panel controls and indicators Number Control/Indicator Description Section 5 4 digit, 7-segment LED display. Normally displays the output current. When the PREV button is pressed, the CURRENT display display indicates the programmed setting of output current. CURRENT indicator Green LED, lights for Constant-Current mode operation. 6 CURRENT control 4 7 OUT button 8 OUT indicator 9 10 11 12 13 14 High resolution rotary encoder for adjusting the Output Current.
Table 4-1: Front Panel controls and indicators Number Control/Indicator Description Green LED, lights when PREV button is pressed. PREV indicator 15 16 Section Voltage and Current Fine/Coarse adjustment control. Operates as a toggle switch. In Fine mode, the VOLTAGE and CURRENT encoders operate with high resolution and in Coarse mode with lower resolution (approx. 6 turns). Auxiliary function: Advanced Parallel Operation Mode setting. Green LED, lights when the unit is in Fine mode.
Table 4-2: Rear panel connections and controls Number Item Description Section 4 Remote Out RJ-45 type connector, used for chaining power supplies to form 7.3 connector a serial communication bus. 7.4 5 Programming and Monitoring connector Connector for remote analog interface. Includes output voltage and 4.5 current limit programming and monitoring signals, Shut-off control (electrical signal), Enable/Disable control (dry-contact), power supply ok (PS_OK) signal and operation mode (CV/CC) signal.
4.4.1 SW1 position functions Refer to Table 4-3 for description of SW1 position functions. The factory default setting is Down for all positions.
4.5 REAR PANEL J1 PROGRAMMING AND MONITORING CONNECTOR The J1 Programming and Monitoring connector is a DB25 subminiature connector located on the power supply rear panel. Refer to Table 4-4 for description of the connector functions. The power supply default configuration is Local operation which does not require connections to J1. For remote operation using J1 signals use the plug provided with power supply or equivalent type.
Fig.4-4: J1 connector terminals and functions Same ground as P/S negative output VMON COM CV/CC IF_COM IF_COM IF_COM IPGM VPGM LOC/ REM 13 25 12 24 11 23 10 22 9 21 8 6 7 20 P IMON IPGM_RTN VPGM_RTN LOC/REM SIGNAL 19 18 5 4 17 3 16 15 2 1 14 Isolated from PS outputs, same ground as RS232/485 ENA SO PS_OK Table 4-4: J1 connector terminals and functions J1 contact Signal name Function Reference J1-1 J1-2 J1-3 IF_COM Isolated Interface Common.
CHAPTER 5 LOCAL OPERATION 5.1 INTRODUCTION This Chapter describes the operating modes that are not involved in programming and monitoring the power supply via its serial communication port (RS232/RS485) or by remote analog signals. Ensure that the REM/LOC LED on the front panel is Off, indicating Local mode. If the REM/LOC LED is On, press the front panel REM/LOC button to change the operating mode to local. - For information regarding remote analog programming refer to Chapter 6.
- Enabled output, power supply in Constant Voltage mode: Press the PREV button and then rotate the CURRENT encoder knob. The CURRENT meter will show the programmed current limit for 5 seconds after the adjustment has been completed, and then will return to show the actual load current. - Enabled output, power supply in Constant Current mode: Rotate the CURRENT encoder knob to adjust the current limit. 4. Adjustment resolution can be set to Coarse or Fine adjustment.
5.4 UNDER VOLTAGE LIMIT (UVL) The UVL prevents adjustment of the output voltage below a certain limit.The combination of UVL and OVP functions, allow the user to create a protection window for sensitive load circuitry. 5.4.1 Setting the UVL level Setting the UVL can be made when the power supply output is Enabled (On) or Disabled (Off). To set the UVL level, press the OVP/UVL button TWICE, so that the CURRENT meter shows “UUL”. The VOLTAGE meter shows the UVL setting level.
When the unit is shut-off by J1 signal, the VOLTAGE display will show “SO” to indicate the unit state. J1 contact 15 is the SO signal input and contacts 2 and 3, IF_COM, are the signal return (connected internally). Contacts 2,3 and 15 are optically isolated from the power supply output. The SO control logic can be selected by the rear panel SW1 Setup switch. Refer to Table 5-2 for SW1 setting and SO control logic.
5.11 SAFE START AND AUTO-RESTART MODES When turning on the power supply AC On/Off, it can start to its last setting of Output Voltage and Current limit with the output enabled (Auto-restart) or start with the output disabled (Safe mode). Press and hold the OUT button to select between Safe start and Auto-restart modes. The VOLTAGE display will continuously cycle between "SAF" and "AU7” every 3 seconds. Releasing OUT pushbutton while one of the modes is displayed, selects that mode.
CAUTION Do not connect power supplies from different manufacturers in series or in parallel. 5.14.1 Series connection for increased output voltage In this mode, two units are connected so that their outputs are summed. Set the current limit of each power supply to the maximum that the load can handle without damage. It is recommended that diodes be connected in parallel with each unit output to prevent reverse voltage during start up sequence or in case one of the units shuts down.
Programming by external resistor is possible . Refer to section 6-5 for details. The communication port is referenced to the IF_COM which is isolated from the power supply output potential. Therefore power supplies connected in series can be chained using the Remote-In and Remote-Out connectors. Refer to chapter 7 for details. 3. Programming by external resistor: 4. Programming via the Serial Communication port (RS232/RS485): 5.14.
5.15 PARALLEL OPERATION Up to four units of the same VOLTAGE and CURRENT rating can be connected in parallel to provide up to four times the output current capability. One of the units operates as a master and the remaining units are slaves. The slave units are analog programmed by the master unit. In remote digital operation, only the master unit can be programmed by the computer while the slave units may be connected to the computer for voltage, current and status readback only.
2. Setting the units as Master or Slave a) Depress and hold the FINE button for 3 seconds. The Master/Slave configuration will be displayed on the Current Display. Rotate the CURRENT encoder to obtain the desired mode. Refer to Table 5-4 for the CURRENT display and modes of operation.
NOTE With local sensing it is important to minimize the wire length and resistance. Also the positive and negative wire resistance should be close as possible to each other to achieve current balance between power supplies.
CHAPTER 6 REMOTE ANALOG PROGRAMMING 6.1 INTRODUCTION The rear panel connector J1 allows the user to program the power supply output voltage and current limit with an analog device. J1 also provides monitoring signals for output voltage and output current. The programming range and monitoring signals range can be selected between 0-5V or 0-10V using the setup switch SW1.
6.4 REMOTE VOLTAGE PROGRAMMING OF OUTPUT VOLTAGE AND CURRENT LIMIT CAUTION To maintain the isolation of power supply and prevent ground loops, use an isolated programming source when operating the power supply via remote analog programming at J1 connector. Perform the following procedure to set the power supply to Remote Voltage programming : 1. Turn the power supply AC On/Off switch to Off. 2.
6.5 RESISTIVE PROGRAMMING OF OUTPUT VOLTAGE AND CURRENT LIMIT For resistive programming, internal current sources, for output voltage and/or output current control, supply 1mA current through external programming resistors connected between J1-9 & 22 and J1-10 & 23. The voltage across the programming resistors is used as a programming voltage for the power supply. Resistance of 0~5Kohm or 0~10Kohm can be selected to program the output voltage and current limit from zero to full scale.
6.6 REMOTE MONITORING OF OUTPUT VOLTAGE AND CURRENT The J1 connector, located on the rear panel provides analog signals for monitoring the output voltage and output current. Selection of the voltage range between 0-5V or 0-10V is made by setup switch SW1-4. The monitoring signals represent 0 to 100% of the power supply output voltage and output current.The monitor outputs have 500 ohm series output resistance.
CHAPTER 7 RS232 & RS485 REMOTE CONTROL 7.1 INTRODUCTION TM This chapter describes the operation of the Genesys 5000W power supplies via the serial communication port. Details of the initial set-up, operation via RS232 or RS485, the command set and the communication protocol are described in this chapter. 7.2 CONFIGURATION 7.2.
2. There are two Remote modes: In this mode, return to local can be made by the front panel REM/LOC or via serial port command RMT 0. Set the unit into Remote mode via serial port RMT 1 command. 1. Remote: 2. Local Lockout: In this mode the unit can be returned to Remote mode via the serial port RMT 1 command or by turning off the AC power until the display turns off and then turn it to on again. In Local Lockout mode, the front panel REM/LOC button is not active.
7.4 CONNECTING POWER SUPPLIES TO RS232 OR RS485 BUS 7.4.1 Single power supply 1. Select the desired interface RS232 or RS485 using rear panel setup switch SW1-6 (section 4-4). - RS232: Down position - RS485: Up position 2. Connect rear panel IN connector to the controller RS232 or RS485 port using a suitable shielded cable. Refer to Figures 7-2, 7-3 and 7-4 for available RS232 and RS485 cables. L=2m typ. 13 8 1 1 Socket DB-25 CONNECTOR PIN NO. 1 2 3 7 NAME SHIELD TX RX SG 8 PIN CONNECTOR PIN NO.
7.4.2 Multi power supply connection to RS232 or RS485 bus Daisy-chain up to 31 units can be connected to RS232 or RS485 bus. The first unit connects to the controller via RS232 or RS485 and the other units are connected with RS485 bus, the user must set all slave supplies to a unique address. No two supplies may have the same address. 1. First unit connection: Refer to section 7.4.1 for connecting the first unit to the controller. 2.
7.5.7 Error message If an error is detected in a command or query, the power supply will respond with an error message. Refer to section 7.6 for details. 7.5.8 Backspace The backspace character (ASCII 8) clears the last character sent to the power supply. 7.6 ERROR MESSAGES The power supply will return error messages for illegal commands and illegal programming parameters. Refer to Table 7-1 for programming error messages and Table 7-2 for commands error messages.
7.7.3 Initialization control commands # 1 2 3 4 5 6 7 Command Description ADR is followed by address which can be 0 to 30 and is used to access the ADR n power supply . Clear status. Sets FEVE and SEVE registers to zero (refer to section 7-8). CLS Reset command.
7.7.5 Output control commands-cont 6 Description Command Reads the actual output current. Returns 5 digits string. MC? (See Note 2) Example: 200A supply sends 000.50, 110.12, 200.00, etc... 7 DVC? Display Voltage and Current data. Data will be returned as a string of ASCII characters. A comma will separate the different fields. The fields, in order, are: Measured Voltage, Programmed Voltage, Measured Current, Programmed Current, Over Voltage Set point and Under Voltage Set Point. Example: 5.9999, 6.
NOTES: 1. In Advanced parallel mode (refer to Sec. 5.15.2), “n” is the total system current. 2. In Advanced parallel mode, “MC?” returns the Master unit current multiplied by the number of slave units. 7.7.6 Global output commands 1. General All supplies, even if not the currently addressed supply, receiving a global command will execute the command. No response to the PC issuing the command will be returned to the PC.
Table 7-4: Current programming range Model GEN8-600 GEN10-300 GEN16-310 GEN20-250 GEN30-170 GEN40-125 GEN60-85 GEN80-65 GEN100-50 GEN150-34 GEN300-17 GEN600-8.5 Minimum (A) 000.00 000.00 000.00 00.00 00.00 00.00 00.000 00.000 00.000 00.000 0.000 0.000 Maximum (A) 600.00 300.00 310.00 250.00 170.00 125.00 85.000 65.000 50.000 34.000 17.000 8.500 NOTE: The power supply can accept values higher by 5% than the table values, however it is not recommended to program the power supply over the rated values.
7.8 STATUS, ERROR AND SRQ REGISTERS 7.8.1 General This section describes the various status error and SRQ registers structure. The registers can be read or set via the RS232/485 commands. When using the IEEE option, refer to the user manual TM for Genesys Power Supply IEEE Programming interface. Refer to Fig.7-7 for the Status and Error Registers Diagram. Command Error (”Cnn”) One response for every command or query received.
7.8.2 Conditional registers Table 7-7: Fault Condition Register BIT Fault name Fault symbol Bit Set condition 0 (LSB) Spare bit SPARE Fixed to zero AC Fail 1 AC AC fail has occurred. OTP OTP shutdown has Over 2 temperature occurred. Foldback shutdown Foldback FOLD 3 has occurred. Bit Reset condition Fixed to zero The AC input returns to normal. The power supply cools down. The supply output is turned On by front panel button or OUT 1 command.
Refer to Tables 7-9 to 7-12 for details of the Enable and Event registers. 1.Fault Enable Register The Fault Enable Register is set to the enable faults SRQs.
3.Status Enable register The Status Enable Register is set by the user to enable SRQs from changes in power supply status. Table 7-11: Status Enable Register BIT Status name 0 (LSB) Constant Voltage Status symbol Bit Set condition CV User command: "SENA nn" is received, where nn is hexadecimal bits. Bit reset condition User command: "SENA nn" is received, where nn is hexadecimal bits. If "nn"=00, no SRQ is sent when there is a change in Status Condition Register.
7.9 SERIAL COMMUNICATION TEST SET-UP Use the following instructions as basic set-up to test the serial communication operation. TM 1.Equipment: PC with Windows Hyper Terminal, private edition, software installed, Genesys power supply, RS232 cable. 2.PC set-up: 2.1 Open Hyper Terminal.......................New Connection. 2.2 Enter a name 2.3 Connect to.......................................Direct to Com1 or Com 2 2.4 Configure port properties: Bits per second .......9600 Data bits ..................
CHAPTER 8 ISOLATED ANALOG PROGRAMMING OPTION 8.1 INTRODUCTION TM Isolated Analog Programming is an internal option card for analog programming of the Genesys power supply series. The option is factory installed and cannot be obtained with GPIB (IEEE) Interface. Output Voltage and Current Limit can be programmed and readback through optically isolated signals which are isolated from all other ground references in the power supply. There are two types of Isolated Analog programming cards: 1.
8.3 ISOLATED PROGRAMMING & MONITORING CONNECTOR Refer to Table 8-1 for detailed description of the rear panel Isolated Programming & Monitoring connector. To provide the lowest noise performance, it is recommended to use shielded-twisted pair wiring. Refer to Fig.8-1 for description of the connector. Isolated programming plug P/N: MC1.5/8-ST-3.81, Phoenix. 1 2 3 4 5 6 7 8 Shield Shield +VPROG_ISO +IPROG_ISO GND +IMON_ISO +VMON_ISO GND Fig.
8.4 SETUP AND OPERATING INSTRUCTIONS CAUTION To prevent damage to the unit, do not program the output voltage and current to higher then the power supply rating. 8.4.1 Setting up the power supply for 0-5/0-10V Isolated Programming and Monitoring Perform the following procedure to configure the power supply: 1. Turn the power supply AC power switch to Off. 2. Connect a short between J1-8 and J1-12 (refer to Table 4-4). 3.
CHAPTER 9 MAINTENANCE 9.1 INTRODUCTION This chapter provides information about maintenance, calibration and troubleshooting. 9.2 UNITS UNDER WARRANTY Units requiring repair during the warranty period should be returned to a Lambda authorized service facility. Refer to the addresses listing on the back cover of this manual. Unauthorized repairs performed by other than the authorized service facilities may void the warranty. 9.
SYMPTOM CHECK Output is present momentarily but shuts off quickly. the display indicates "OUP". Output voltage will not adjust. Front panel CC LED is on. Output voltage will not adjust. Front panel CV LED is on. Is the power supply configured to Remote sense? Is the unit in constant current mode? Check if output voltage is adjusted above OVP setting or below UVL setting.
Kapitel 9 Wartung & Service 9.1 Einleitung Dieses Kapitel liefert Informationen über Wartung und Fehlersuche. 9.2 Reparaturen während der Garantie Sollte ein Gerät innerhalb der Garantiezeit ausfallen, so dürfen Reparaturen nur durch Lambda oder autorisierte Servicestellen durchgeführt werden. Die Adressen finden Sie am Ende dieses Handbuches. Eingriffe in die Geräte durch nicht autorisierte Stellen führen zum Verlust des Garantieanspruches. 9.3 Periodische Wartung Die Geräte sind wartungsfrei.
Tabelle 9-1: Fehlersuche Symptom Keine Ausgangsspannung. Displays und Anzeigen sind dunkel. Prüfung Ist das Netzkabel defekt? Tätigkeit Ref. Falls erforderlich, Netzkabel 3.7 ersetzen. Ist die Netzspannung Netzspannung prüfen, Gerät an 3.6 innerhalb des passende Versorgungsspannung Eingangsbereiches? anschließen. Ausgangsspannung liegt Bricht die Netzspannung Netzspannung prüfen, Gerät an 3.6 kurzfristig an, schaltet aber zusammen wenn am Ausgang passende Versorgungsspannung sofort wieder ab.
9.7 Sicherungswerte Im Gerät befinden sich keine Sicherungen die durch den Anwender ersetzt werden können. Sicherungen sind als Schutz eingebaut, falls im Gerät Fehler auftreten sollten. Sollte eine Sicherung auslösen, so muss das Gerät zur Reparatur gegeben werden. Sicherungen dürfen ausschließlich von dafür geschultem, technischen Personal ausgewechselt werden. In Tabelle 9-2 sind die Sicherungswerte aufgelistet.
USER MANUAL INDEX A ac cables ac fail accessories acknowledge address adjustment auto-restart 9, 16 30 9 52 19, 49 66 39 B back space baud rate bipolar voltage 53 19, 49 41 C calibration configuration checksum communication constant current constant voltage cooling cv indicator cc indicator 66 49 52 52, 62 18, 35 18, 35 9, 11 28, 38 28, 38 D daisy-chain display 44, 52 28 E enable error message external resistor external voltage F fine foldback fuse front panel control front panel locking 34 53 47 4
NOTES
