Data Sheet

Genesys™ 2.4kW-1U
3|
Genesys ™ 2.4kW Specifications
*1: Minimum voltage is guaranteed to maximum 0.2% of rated output voltage.
*2: Minimum current is guaranteed to maximum 0.4% of rated output current.
*3: For cases where conformance to various safety standards (UL, IEC, etc›) is required, to be
described as 190-240Vac (50/60Hz) for 3-Phase 208V models.
*4: 3-Phase 208V models: At 208Vac input voltage. With rated output power.
*5: Not including EMI filter inrush current, less than 0.2mSec.
*6: 3-Phase 208V models: 170~265Vac, constant load.
*7: From No-Load to Full-Load, constant input voltage. Maximum drop in Remote Sense.
*8: For 8V~300V models: Measured with JEITA RC-9131A (1:1) probe. For 600V model: Measured
with 10:1 probe.
*9: From 10% to 90% or 90% to 10% of Rated Output Voltage, with rated, resistive load.
*10:From 90% to 10% of Rated Output Voltage.
*11: For load voltage change, equal to the unit voltage rating, constant input voltage.
*12: For 8V~16V models the ripple is measured from 2V to rated output voltage and rated output
current. For other models, the ripple is measured at 10~100% of rated output voltage and rated
output current.
*13: The Constant Current programming readback and monitoring accuracy does not include the
warm-up and Load regulation thermal drift.
1.2 CONSTANT CURRENT MODE
1.Max.line regulation (0.01% of Io rated+2mA)(*6)
2.Max.load regulation (0.02% of Io rated+5mA)(*11)
3.Ripple r.m.s 5Hz~1MHz. (*12)
4.Temp. coefficient
8V ~ 20V models: Less than ±0.5% of rated output current over 30 minutes following power On.
1.3 PROTECTIVE FUNCTIONS
1. OCP
2. OCP Foldback
3. OVP type
4. OVP trip point
6. Over Temp. Protection
0~105% Constant Current
Output shut down when power supply change from CV to CC. User selectable.
Inverter shut-down, manual reset by AC input recycle or by OUT button or by communication port command.
User selectable , latched or non-latched.
5~88V 5~110V 5~165V 5~330V 5~660V
3.Rated Output Power
1.0 MODEL
1.Rated output voltage(*1)
2.Rated Output Current(*2)
2.Display
3.Indications
Voltage: 4 digits , Accuracy: 0.5% of rated output Voltage ±1 count.
Current: 4 digits, Accuracy: 0.5% of rated output current ±1 count.
Voltage, Current, Alarm, Fine, Preview, Foldback, Local, Output On, Front Panel Lock, CV/CC.
1.5 FRONT PANEL
1.Control functions
Vout/ Iout manual adjust by separate encoders (coarse and fine adjustment selectable).
OVP/UVL manual adjust by Volt. Adjust encoder.
Address selection by Voltage (or current) adjust encoder. Number of addresses:31.
On/Off, Output on/off, Re-start modes (auto, safe), Foldback control (CV to CC), Go to local control.
Re-start modes (automatic restart, safe mode).
Baud rate selection: 1200,2400,4800,9600 and 19,200.
1.4 ANALOG PROGRAMMING AND MONITORING
1.Vout Voltage Programming
2.Iout Voltage Programming (*13)
3.Vout Resistor Programming
4.Iout Resistor Programming (*13)
5.On/Off control (rear panel)
6.Output Current monitor (*13)
7.Output Voltage monitor
8.Power Supply OK signal
9. CV/CC Indicator
10. Enable/Disable
0~100%, 0~5V or 0~10V, user select. Accuracy and linearity:±0.5% of rated Vout.
0~100%, 0~5V or 0~10V, user select. Accuracy and linearity:±1% of rated Iout.
0~100%, 0~5/10Kohm full scale,user select.,Accuracy and linearity: ±1% of rated Vout.
0~100%, 0~5/10Kohm full scale,user select. Accuracy and linearity:±1.5% of rated Iout.
By electrical. Voltage: 0~0.6V/2~15V,or dry contact ,user selectable logic.
0~5V or 0~10V , Accuracy:±1% , user selectable.
0~5V or 0~10V ,Accuracy:±1% ,user selectable.
TTL high (4~5V) -OK, 0V-Fail 500ohm series resistance.
Dry contact. Open:off , Short: on. Max. voltage at Enable/Disable in: 6V.
11. Local/Remote analog control
12. Local/Remote analog control Indicator
Open collector, CC mode: On, CV mode: Off, Maximum voltage: 30V, maximum sink current: 10mA
Open collector, Local: Off, Remote: On. Maximum voltage: 30V, maximum sink current: 10mA.
1.Max.line regulation (0.01% of rated Vo+2mV)(*6)
2.Max load regulation (0.015% of rated Vo+5mV)(*7)
3.Ripple and noise p-p 20MHz (*8)
4.Ripple r.m.s 5Hz~1MHz
5.Remote sense compensation/wire
8.Warm-up drift
9.Up-prog. response time, 0~Vo Rated (*9)
10.Down-prog response time
No-load (*10)
11.Transient response time
100PPM/°C of rated output voltage,following 30 minutes warm-up
30mS
Time for output voltage to recover within 0.5% of its rated output for a load change 10-90% of rated output
current. Output set-point: 10-100%, local sense.
Less than 1mSec for models up to and including 100V. 2msec for models above 100V
100
100mS
80
7.Temp. stability
6.Temp. coefficient
Full-load (*9)
0.05% of rated Vout over 8hrs interval following 30 minutes warm-up. Constant line, load & temp.
Less than 0.05% of rated output voltage+2mV over 30 minutes following power On.
5.Temp. stability
6.Warm-up drift
100PPM/ºC from rated output current, following 30 minutes warm-up.
0.05% of rated Iout over 8hrs. interval following 30minutes warm-up. Constant line, load & temperature.
5. Output Under Voltage Limit
Preset by front panel or communication port. Prevents from adjusting Vout below limit.
2.4
5.8
7
600
62
95
300
75
5
2.8
6.6
15
300
32
50
150
35
5
3000
3.6
8.2
30
150
17
27.5
100
25
5
2500
4.4
9.8
40
100
12
20
80
8
5
1500
5
11
50
80
10
17
80
8
5
1200
6
13
70
5~66V
60
8
14
60
8
5
1100
2~44V
8
17
120
40
6
11
60
8
5
1000
2~36V
10
21
220
30
5
9.5
60
8
5
900
1~24V
14
29
480
20
4
8
60
8
2
800
1~19V
17
35
600
16
3.6
7.4
60
8
2
30
700
0.5~12V
26
53
960
10
3
6.5
60
8
2
600
0.5~10V
32
65
1200
8
2.8
6.2
60
8
2
10
500
mA
mA
mA
V
A
W
mV
mV
mV
mV
V
PPM/°C
mS
mS
mS
mS
PPM/°C
60mS
1.1 CONSTANT VOLTAGE MODE
30V ~ 600V models: Less than ±0.25% of rated output current over 30 minutes following power On.
4
2400
A
8
2400
B
16
2400
A
24
2400
C
30
2400
C
40
2400
A
60
2400
B
80
2400
B
120
2400
C
150
2400
B
240
2400
C
300
2400
A
4.Development Priority
---
By electrical signal or Open/Short: 0~0.6V or short: Remote, 2~15V or open: Local.
5. OVP/UVL Programming
Resolution (0.1% of Vo Rated)
Accuracy (1% of Vo Rated)
4. Readback Current
Resolution (0.012% of Io Rated )
Accuracy (0.3% of Io Rated+0.1% of Io Actual Output) (*13)
3. Readback Voltage
Resolution (0.012% of Vo Rated)
Accuracy (0.1%Vo Rated+0.1% of Vo Actual Output)
2. Remote Current Programming (16 bit)
Resolution (0.012% of Io Rated)
Accuracy (0.2% of Io Rated+0.1% of Io Actual Output) (*13)
1.6 Interface RS-232&RS-485 or Optional GPIB / LAN Interface
Model
1. Remote Voltage Programming (16 bit)
Resolution (0.012% of Vo Rated)
Accuracy (0.05%Vo Rated+0.05% of Vo Actual Output)
72
16
1200
0.48
12
600
72
600
600
6000
0.48
36
32
600
0.96
24
300
36
300
300
3000
0.96
18
64
300
1.92
48
150
18
150
150
1500
1.92
12
96
200
2.88
72
100
12
100
100
1000
2.88
9.6
120
160
3.6
90
80
9.6
80
80
800
3.6
7.2
160
120
4.8
120
60
7.2
60
60
600
4.8
4.8
240
80
7.2
180
40
4.8
40
40
400
7.2
3.6
320
60
9.6
240
30
3.6
30
30
300
9.6
2.4
480
40
14.4
360
20
2.4
20
20
200
14.4
1.92
600
32
18
450
16
1.92
16
16
160
18
1.2
960
20
28.8
720
10
1.2
10
10
100
28.8
0.96
1200
16
36
900
8
0.96
8
8
80
36
mV
mV
mA
mA
mV
mV
mA
mA
V
mV
mV
GEN
8-300 10-240 16-150 20-120 30-80 40-60 600-4300-8150-16100-2480-3060-40
15mS