Instructions

ManualsBrandsTDE Instruments ManualsDigital Panel MetersDigalox Digital rack-mount meter









Graphical panel meter for 500V/333mV AC/DC with RGB multi display

 Panel meter Digalox DPM72-MPN

, mounting bracket,

5 jumpers, 2 instruction manuals (EN + DE)

!" #$%

• Read instruction manual carefully before operating the device! Keep for later

reference.

• Mounting and installation must be carried out by suitably qualified and competent

persons only.

• &'( )*+$*,%$*

-

• &*.*,*/,0,

*  ,-  )*    1!1!      ,  $  *  

"

• )*,0,*%+,+

*,."

• The device is not intended to protect persons or facilities against harm. Specific

devices must be used to guarantee safety (protection relays, cut-off switches,

etc.).

• When connecting switches to the terminals J1-J6, only switches must be used

whose isolation voltage is at least twice the maximum occurring measurement

voltage. For example, when measuring 250;V AC switches must be isolated for at

least 500;V.

• Do not open the housing!

• Do not use the device in the presence of explosive or flammable substances!

• All cables carrying hazardous voltages must be secured with external separators.

" $%0

General warning sign

(Attention, observe the documentation!)

Warning of an electrical hazard

-----!23-----

Summary of content (8 pages)

PAGE 1
Digalox DPM72-MPN+ Instruction manual (Rev-2020-09) Graphical panel meter for 500V/333mV AC/DC with RGB multi display Package contents: Panel meter Digalox DPM72-MPN+, mounting bracket, 5 jumpers, 2 instruction manuals (EN + DE) 1. Safety instructions • Read instruction manual carefully before operating the device! Keep for later reference. • Mounting and installation must be carried out by suitably qualified and competent persons only.
PAGE 2
3. Intended use • Measurement of current, voltage, power and frequency in the specified measuring ranges. • Indoor use non condensing, non corrosive. • Panel mounting. • In operation, supply the device preferably via screw terminals with 12 to 24 V AC/DC. If the device is supplied via USB in operation, USB supply voltage must be at least 5 V. • Failure to comply with these instructions will void all guarantee and warranty. 4.
PAGE 3
5. Product overview 2 Front 1 Unit or free text 1 3 2 Threshold values 3 Upper scale caption 2 6 4 4 Graphical measurement display 5 5 Digital measurement value 6 Lower scale caption 2 1 3 J12 Bus 1 J11 Bus 2 J10 NC J9 NC J8 GPIO 1 J7 GPIO 2 J6 Mode 1 J5 Mode 2 J4 Mode 3 J3 Autoscale J2 Min/Max J1 Timebase Outputs max. 30 V 50 mA – + Supply 12 - 24 V ~/ Digalox DPM72-MPN+ www.digalox.com Made in Germany USB 4 U2low U2high U1high U1low Shunt 333 mV max.
PAGE 4
7. Electrical connections Supply 12 - 24 V Voltage direct U2low U2high U1high U1low Sicherung 250 mA − Digalox max. 500 V + Supply + - Current via external shunt Current via external shunt, voltage direct U2low U2high U1high U1low U2low U2high U1high U1low max. 333 mV Shunt max. 333 mV Load + - Shunt max.
PAGE 5
8. Configuration Connect the device to a computer: USB: Connect the device and the computer using a USB cable. The device driver is installed automatically if the computer is connected to the Internet. XBEE: Insert the XBEE stick into the computer. The device driver is installed automatically if the computer is connected to the Internet. In order to reset the XBEE settings, short-circuit terminal J8. RS485: Short-circuit terminal J8. Connect the device to the computer using an RS485 USB adapter.
PAGE 6
9. Other settings The following functions can be activated independently during operation by shortcircuiting connectors J1-J3, e.g. using a jumper or switch: J1: Graphical historic data display The unit displays the stored values within the set time base as a graphical trend. The time base can be set to days (7, 14), hours (1, 3, 6, 12, 24, 48, 72), minutes (3, 15, 30) or seconds (36). The time base can be changed by alternately opening and closing J1 (interval < 2 sec).
PAGE 7
10. Maintenance Periodically check all external cable connections. 11. Cleaning Observe the safety instructions before cleaning the device. Clean the device with a dry lint-free soft cloth. Do not use solvents. 12.
PAGE 8
Depth Net weight 13. Dimensions [mm] 55.3 mm (with plugs, cable direction rear facing) 72.6 mm (with antenna) 149 g 58.2 56.3 83.5 72.0 67.5 63.0 83.5 72.0 86.9 2.9 35.9 72.0 36.7 77.5 Panel cut-out 72.0 73.5 14. Available accessories TDE Instruments Digalox DPM72 gasket EPDM/SBR 15. Contact information TDE Instruments GmbH, Gewerbestraße 8, D-71144 Steinenbronn Phone: +49 7157 20801 E-Mail: info@tde-instruments.de Internet: www.tde-instruments.de, www.digalox.com ----- 8 / 8 ----- 68.