Instructions

ManualsBrandsTDE Instruments ManualsDigital Panel MetersDigalox Digital rack-mount meter











  !"#$%"

' ()'

*'$+,-&,.

! "#$

•      (     /0  1    

2

• " (((3

2

• %&''()*+#*,$#*

-

• %*.*,*/,0,

*  ,-  )*    1 1       ,  #  *  

!

• )*,0,*$+,+

*,.!

• 4/ 25

/( +'%'

2.2

• 6 7%78'(

/ ! 

/ 29!' $:(

:2

•  0

• /!/((0

• ( ;/ (!2

! #$0

  

+'(/0.

6 ;

%%%%% 23%%%%%

Summary of content (8 pages)

PAGE 1
Digalox DPM72-MP+ Instruction manual (Rev-2020-09) Graphical panel meter for 500V/10A AC/DC with RGB multi display Package contents: Panel meter Digalox DPM72-MP+, mounting bracket, 5 jumpers, 2 instruction manuals (EN + DE) 1. Safety instructions • Read instruction manual carefully before operating the device! Keep for later reference. • Mounting and installation must be carried out by suitably qualified and competent persons only.
PAGE 2
3. Intended use • Measurement of current, voltage, power and frequency in the specified measuring ranges. • Indoor use non condensing, non corrosive. • Panel mounting. • In operation, supply the device preferably via screw terminals with 12 to 24 V AC/DC. If the device is supplied via USB in operation, USB supply voltage must be at least 5 V. • Failure to comply with these instructions will void all guarantee and warranty. 4.
PAGE 3
5. Product overview 2 Front 1 Unit or free text 1 3 2 Threshold values 3 Upper scale caption 2 6 4 4 Graphical measurement display 5 5 Digital measurement value 6 Lower scale caption 2 1 3 J12 Bus 1 J11 Bus 2 J10 NC J9 NC J8 GPIO 1 J7 GPIO 2 J6 Mode 1 J5 Mode 2 J4 Mode 3 J3 Autoscale J2 Min/Max J1 Timebase Outputs max. 30 V 50 mA – + Supply 12 - 24 V ~/ Digalox DPM72-MP+ www.digalox.com Made in Germany USB 4 Ilow Ihigh 10 A max.
PAGE 4
7. Electrical connections Supply 12 - 24 V Voltage direct Ilow Fuse 250 mA − Digalox Ihigh max. 10 A + +/L -/N Supply Current and voltage direct Uhigh Ulow Ilow Ihigh max. 10 A Load FF +/L -/N Ilow Uhigh Ulow +/L -/N Uhigh Ulow max. 500 V 10 A Current Load +/L -/N Transformer Current Load +/L -/N Transformer Current on high side, 50 V max! Ihigh Load Ihigh max. 10 A FF 10 A max. 10 A max. 500 V Current via current transformer, voltage direct max.
PAGE 5
8. Configuration Connect the device to a computer: USB: Connect the device and the computer using a USB cable. The device driver is installed automatically if the computer is connected to the Internet. XBEE: Insert the XBEE stick into the computer. The device driver is installed automatically if the computer is connected to the Internet. In order to reset the XBEE settings, short-circuit terminal J8. RS485: Short-circuit terminal J8. Connect the device to the computer using an RS485 USB adapter.
PAGE 6
9. Other settings The following functions can be activated independently during operation by shortcircuiting connectors J1-J3, e.g. using a jumper or switch: J1: Graphical historic data display The unit displays the stored values within the set time base as a graphical trend. The time base can be set to days (7, 14), hours (1, 3, 6, 12, 24, 48, 72), minutes (3, 15, 30) or seconds (36). The time base can be changed by alternately opening and closing J1 (interval < 2 sec).
PAGE 7
10. Maintenance Periodically check all external cable connections. 11. Cleaning Observe the safety instructions before cleaning the device. Clean the device with a dry lint-free soft cloth. Do not use solvents. 12.
PAGE 8
13. Dimensions [mm] 58.2 56.3 83.5 72.0 67.5 63.0 83.5 72.0 86.9 2.9 35.9 72.0 36.7 77.5 Panel cut-out 72.0 73.5 14. Available accessories TDE Instruments Digalox DPM72 gasket EPDM/SBR 15. Contact information TDE Instruments GmbH, Gewerbestraße 8, D-71144 Steinenbronn Phone: +49 7157 20801 E-Mail: info@tde-instruments.de Internet: www.tde-instruments.de, www.digalox.com ----- 8 / 8 ----- 68.0 2.9 27.0 9.6 55.3 18.6 68.