Instructions

ManualsBrandsTDE Instruments ManualsDigital Panel MetersDigital rack-mount meter Digalox DPM72-MP Graphic DIN multiple measuring device 500V/10

(Rev-2020-09)

Visit  to download the software “Digalox Manager”.

Panel meter Digalox DPM72, 5$× jumpers, 1$× mounting bracket

 

 Indoor use non condensing, non corrosive.

 Panel mounting.

 Failure to comply with these instructions will void all guarantee and warranty.

 In operation, supply the device preferably via screw terminals with 12 to 24$V

AC/DC. If the device is supplied via USB in operation, USB supply voltage must

be at least 5$V.

  

 !  "#    $    #  %      #

%&

 '##%#(%)

#%&

 "#%)# $%%$%

#

 Read instruction manual carefully before operating the device!

 The device is not intended to protect persons or facilities against harm. Specific

devices must be used to guarantee safety (protection relays, cut-off switches,

etc.).

 When connecting switches to the terminals J1-J6, only switches must be used

whose isolation voltage is at least twice the maximum occurring measurement

voltage. For example, when measuring 250$V AC switches must be isolated for

at least 500$V.

 Do not open the housing!

 Do not use the device in the presence of explosive or flammable substances!

 All cables carrying hazardous voltages must be secured with external separators.

-----  -----

Summary of content (8 pages)

PAGE 1
Digalox DPM72-MP Instruction manual (Rev-2020-09) Visit www.digalox.com to download the software “Digalox Manager”. Package contents: Panel meter Digalox DPM72, 5 × jumpers, 1 × mounting bracket 1. Intended Use  Indoor use non condensing, non corrosive.  Panel mounting.  Failure to comply with these instructions will void all guarantee and warranty.  In operation, supply the device preferably via screw terminals with 12 to 24 V AC/DC.
PAGE 2
3. Description The multi display with RGB backlight is able to display up to 4 parameters simultaneously. Thresholds can be associated with individual warning backlight colours. The unit can be switched between measurement modes via an external switch. Minimum and maximum values of up to four parameters are recorded and can be displayed optionally using an external switch. Measured values of one parameter are recorded over a time span of three minutes up to 14 days.
PAGE 3
4. Electrical Connections Supply 12 - 24 V Voltage direct Ilow Fuse 250 mA − Digalox Ihigh max. 10 A + +/L -/N Supply Current and voltage direct Uhigh Ulow Ilow Ihigh max. 10 A Load FF +/L -/N Current via current transformer Ihigh Ilow Uhigh Ulow Ihigh +/L -/N Uhigh Ulow max. 10 A FF max. 500 V 10 A Current Load +/L -/N Transformer Current on high side, 50 V max! Ihigh Load max. 500 V Current via current transformer, voltage direct 10 A max. 10 A Load 10 A max.
PAGE 4
5. Configuration The device can be configured via DIP switches and jumpers manually or with the corresponding software “Digalox Manager” via USB interface. When configuring via DIP switches and jumpers the basic settings can be made computer-independent. The configuration with the software “Digalox Manager” allows full functionality. Scaling via DIP switches In modes where a scaling is necessary to represent the correct measurement value (e.g.
PAGE 5
Configuration via DIP switches and jumpers if it is required to switch between multiple measurement modes via an external switch (Save mode) The required measurement modes are configured and saved sequentially. 1. Set DIP-switch 10, 11 and 12 to OFF position. 2. Connect supply voltage. 3. Set the measurement mode with jumpers at J4-J6 according to table "Measurement mode”, column “Save mode". 4. Set DIP switch 10 to ON position. 5.
PAGE 6
Table common switch combinations (DIP switch 1-9) Value 10 Combination ON Value 50 1 2 3 4 5 6 7 8 9 10 11 12 20 1 2 3 4 5 6 7 8 9 10 11 12 25 1 2 3 4 5 6 7 8 9 1 0 11 12 250 ON ON ON 1 2 3 4 5 6 7 8 9 1 0 11 1 2 500 ON Combination 1 2 3 4 5 6 7 8 9 1 0 11 1 2 1 2 3 4 5 6 7 8 9 10 11 1 2 150 ON ON Value 200 1 2 3 4 5 6 7 8 9 10 11 1 2 100 ON Combination ON 1 2 3 4 5 6 7 8 9 1 0 11 1 2 1 2 3 4 5 6 7 8 9 10 11 12 Table measurement mode Measurement mode V DC direct Display Scale Vo
PAGE 7
6. Other settings The following functions can be activated independently by short-circuiting connectors J1-J3 by jumper or switch during operation: J1: Graphical historic data display To activate the graphical historic data display connector J1 is shorted. The unit displays the stored values within the set time base as a graphical trend. The time base can be set to days (7, 14), hours (6, 12, 24, 48, 72) or minutes (3, 15, 30, 60).
PAGE 8
7. Mounting Carefully insert the device into the panel cut-out. Insert the mounting bracket from the back and push towards the panel until the device sits tight. Make sure the mounting bracket is snapped into the side of the housing. To ensure IP65 protection (dust and water jet) when mounting in a front panel, use optional gasket (separately available). 8.