Data Sheet

PRODUCT INFORMATION (BRIEF)
Series TASTA
Video indoor station for hands-free talking
IVW5110-0145
IVW5111-0145
German / English
SCOPE OF DELIVERY
1 x Indoor station IVW511x-0145
1 x Mounting tray with connection terminal
1 x Product information (brief)
1 x Instruction manual
PI_IVW511x-0145 System manual
DEVICE OVERVIEW
1
Sensor button colour
2
Sensort button
image activation
3
Function button
4
Light switch button
5
Door release button
6
LED indication (blue)
for door release
7
Ambient illumination
8
LED indication (green) for
incoming calls / speaking
9
Speech button
10
Volume button
11
LED indication (red) ring
tone mute
12
Smart Slot
14
Sensor button brightness
15
Sensor button contrast
SAFETY INSTRUCTIONS
General safety instructions
Assembly, installation, commissioning and repair of
electronic devices must be carried out by qualified
electricians. Observe the latest regulations and standards
for system installations.
WARNING! Danger due to electrical shock.
Observe the safety regulations according to DIN VDE
0100, when working on main power connections of 230 V.
When installing TCS:BUS systems the general safety
regulations for telecommunication systems according
to VDE 0800 must be observed. Inter alia:
> separated cable routing of high and low voltage lines,
> minimum distance of 10 cm in case of a common cable
routing,
> use of separators between high and low voltage lines within
shared cable ducts,
> use of standard telecommunication lines, e.g. J-Y (St) Y with
0.8 mm diameter,
> already existing lines (modernisation) with deviating
cross-sections can be used in compliance with the loop
resistance.
Requirements to protect against lightning
CAUTION! Device damage due to overvoltage.
By suitable lightning protection measures it has to be
ensured that the electric voltage of 32 V DC at each connec-
tion is not to be exceeded.
PRODUCT DESCRIPTION
Intended use
IVW511x-0145 is a video indoor station for hands-free talking.
It is suitable exclusively for operation at TCS:BUS. Type of
installation: surface-mount.
For applications, which differ from the intended use or
goes beyond it, the manufacturer accepts no liability.
SPARE PARTS, ACCESSORIES
Mounting tray .................................................ZIA5002-0145
Mounting plate ...............................................ZIA5004-0145
Desktop accessory ........................................ZIT5000-0030
Radio signal unit ............................................FFL2200-0
INDICATION AND OPERATING ELEMENTS
1 > shortly touch: adjustable in 8 steps
2
> shortly touch: video image of the front door camera is
displayed or switching-over between different cameras
3
> send control function 8, send internal call, door release
automatic on / off or call diversion on / off configurable
> ring tone selection: internal call
4
> switch light
> ring tone selection: floor call
> ambient illumination: press 4 sec to de-/activate the
ambient illumination
5
> door release
> trigger light switch function, only if the light switch
function is activated in the front door station
> terminate speaking: voice connection is terminated
automatically after 4 sec
> ring tone selection: door call 1 from the front door station
6
> LED off: door opener in standby
> LED on: automatic door release activated
> LED lights up for 3 sec: door is opened
> ambient illumination is switched on, operational readiness
> blinks: a call is displayed, if configured
> LED off: temporary (manually) or permantently switched off
> LED on: temporary (manually) or permantently switched on
8
> LED off: in standby
> LED on: call, speaking activated
> blinks 3 x: speech channel is busy
9
> shortly press: call acceptance, speaking activated
> press for 2 sec: duplex communication is activated
> speaking terminated
> ring tone selection: door call 2 from front door station
10
> setting the ring tone volume in 4 steps, when no voice
connection is established
> setting the volume of the voice output in 4 steps when
a voice connection is established
11
> LED off: ring tone mute is deactivated
> LED on: ring tone mute is activated
> blinks: ring tone programming mode
> flashes: call diversion activated, ring tone mute deactivated
> LED turns off in longer periods: call diversion activated,
ring tone mute activated
12
> for additional signalling of door calls, can be ordered
as asseccory
13
> shortly press: ring tone mute activated
> press for 8 s: initiate / terminate ring tone selection
> terminate the duplex communication
14
> shortly touch: adjustable in 8 steps
15
> shortly touch: adjustable in 8 steps
TECHNICAL SPECIFICATIONS
Supply voltage .................. +24 V ± 8 % (TCS:BUS power
supply and control unit)
6-wire operation .............. input current: I(a) = 0.13 mA
I(P) in standby: 3.18 mA
I(Pmax): 147.0 mA
Video module ................... TFT colour
Display size ...................... 8.9 cm (3.5 inch)
Resolution ........................ 320 x 240 pixel, RGB
Video signal input ............ symmetrical 1 Vss FBAS
Degree of protection ........ IP30
Acceptable ambient
temperature ..................... - 5 ...+ 40 °C
Housing ............................ plastics ASA
Dimensions (in mm) ........... H 194 x W 94 x D 21 (mounting tray),
D 17 (mounting plate)
Weight .............................. 227 g (incl. mounting tray)
INSTALLATION
Mounting height
For an optimal operation, install the video indoor station 1.60
m (upper egde of the device) above the ground.
Install the mounting tray
Insert the lines through the cable gland. Connect the wires
to the terminals (a, b, E, P, P, M, V1 und V2). Fix the mounting
tray with suitable screws to the wall.
Observe the installation position of the mounting tray.
It is marked by an arrow and the designation TOP.
13
Call OFF button
Install the mounting plate
If the installation of a flush-mounted socket is possible,
use the mounting plate. The mounting plate is
available as accessory (article: ZIA5004-0145).
Remove the device
Insert a screw driver with slight pressure into the release
opening (1). Pull off the device from the front at its upper side.
Lift the device out of the adjustment increments (2).
Snap on the device
Put the device onto both adjustment increments of the mounting
tray (1). Press the device against the latch until it snaps-on (2).
Example circuit:
floor push
button
IVW511x
AVC11010
BVS20 NGV1011
Connecting the floor push button
Connect the floor push button to the terminals E – P an.
Alternatively you can connect the floor push button to
the terminals a – E. Ensure that the a-wire of the con-
trol unit is connected to the a-terminal of the indoor station.
Error detection and indication
Indication error mode, if error detected: All 3 LEDs are flashing.
Pressing any button of the device triggers the output of an
error tone.
Error tone - error causes and troubleshooting
The error tone sounds 1 x long and 3 x short:
> a- and P-wire are exchanged or short-circuited
> exchange a- and P-wire or remove short-circuit,
device is in standby mode again
The error tone sounds 1 x long and 2 x short:
> a-wire: not connected or not supplied
> connect a-wire or check power supply,
device is in standby mode again
The error tone sounds 1 x long and 1 x short:
> button stucks (pressed longer than 15 sec)
> loosen the button at the device or the floor push button,
device is in standby mode again
Matching resistor
If the video indoor station is placed at the end of a strand or
is the only device at the TCS:BUS, the matching resistor is
to be activated.
Ex works the video indoor station is not set up for the
operation at the end of the strand.
BELL BUTTON PROGRAMMING
Basic principle:
All devices at the TCS:BUS have an unique serial number.
The serial number of the indoor station is allocated to the bell
button of the front door station. The allocation is stored in the
EEPROM of the front door station.
Requirements for the programming:
> Ensure that the access to the indoor station in the flat is
granted.
> Check if the indoor station is connected to the TCS:BUS.
> Switch on the mains voltage. The operating LED at the power
supply and control unit is on.
> Check if a programming lock is set. If the programming
lock is activated, you cannot program any bell button. To
deactivate the programming lock you need a Service Device
TCSK or the configuration software configo
TM
.
> For device-specific indication modes of the front door station
see product information of the front door station.
1. Control unit:
Switching on the programming mode of the system
> shortly press the RUN/PROG button
a)
> LED blinks
> programming mode is activated
2. Programming via voice connection
> press the speech button
> shortly press the bell button
> ring tone sounds at the front door and indoor station
c)
> press the speech or door release button
3. Control unit:
Switching off the programming mode of the system
> shortly press the RUN/PROG button
> LED lights up
> programming mode is deactivated
e)
Deleting bell buttons
b)
> press the bell button that is to be deleted for around 6 sec
until an acknowledgement tone sounds
c)
> release the bell button
> previously execute step 1 and the step 3
Notes:
a)
Do not press the RUN/PROG button longer than 5 sec.
Otherwise you will activate the light switch function of the
front door station. The bell button cannot be programmed.
Repair:
> If the LED blinks, shortly press the RUN/PROG button to
deactivate the programming mode.
> Press the RUN/PROG button only short to activate the
programming mode.
> Programm the the bell button.
b)
Not necessary, if the bell buttons have not been program-
med, see product information of the front door station.
c)
If there sounds a Progsperr tone (long high tone followed by
long low tone) instead, the front door station is equipped with
a programming lock. You can deactivate the programming
lock only with the Service Device TCSK or the configuration
software configo
TM
.
Further information (parallel call with only one bell
button) can be found in the system manual, in the down-
load area at www.tcsag.de or by scanning the QR code.
BVS20
ISW5110
AVC11010
LED
COMMISSIONING
Install all devices of the system completely. Check all wire
against each other on short-circuit. Switch on
the mains power.
Bell button
Speech button
RUN/PROG button
7
NOTES
Conformity
Declarations of conformity are available for
download www.tcsag.de.
Information of disposal
Dispose the device separately from domestic waste
via a collection point for electronic scrap. Ask your
county administration for the responsible collection
point.
Dispose the parts of the packaging in collecting
tanks for cardboard and paper resp. plastics.
Service
For detailed information visit our website www.tcsag.de.
Download or scan the QR code.
HOTLINE
Fon [phone],
Fax [phone]
E-Mail [e-mail]
Printout: 08/2018 | Subject to technical changes.
kPI_IVW511x-0145 6 A
www.tcsag.de
ORDER DIVISION
Fon [phone]
Fax [phone]
E-Mail [e-mail]
SALES
Fon [phone]
Fax [phone]
E-Mail [e-mail]
TRAINING COURSES
Fon [phone]
Fax [phone]
E-Mail [e-mail]
TCS TürControlSysteme AG
Geschwister-Scholl-Straße 7
D-39307 Genthin, GERMANY
Fon: [phone]
Fax: [phone]
activated
deactivated
1
2
remove the device
2
1
snap-on the device
TCS Österreich GmbH
Gewerbepark 21
A-2821 Lanzenkirchen, AUSTRIA
Fon: [phone]
Fax: [phone]