Manual

GB - 2PI_FFA1210_Art0017978_1v2 126301-02
TCS TürControlSysteme AG
Geschwister-Scholl-Straße 7 • D-39307 Genthin
extent
TM
6.3 Function programming
Notes:
– If a radio sensor was assigned to a channel, this one is
activated after the recognition of the radio sensor (LED 1
or 2 blinks orange).
– If a radio sensor was assigned to both channels, primarily
only channel 1 is activated after recognition (LED 1 blinks).
Both function and parameter can then be adjusted for
channel 1. If subsequently the button CLR/MODE is
pressed, channel 2 is activated (dashed line). Following,
function and parameters can be adjusted for channel 2.
– If no action takes place, function programming will be
terminated after 30 s.
7. Functions
7.1 extent
TM
radio sensors
7.1.1 Function 1 (Two-button operation)
Note: Default function for a radio sensor just assigned to
the radio actuator and also the function for motion sensors!
7.1.2 Function 2 (One-button operation)
7.1.3 Function 3 (Button control)
7.1.4 Function 4 (Stairwell light)
Note: Following the preset running time, the light will be
switched off for 2 s (switch-off warning) and then switched
on again for another 30 s.
7.1.5 Function 5 (Time switch)
7.1.6 Function 6 (Fan control)
7.1.7 Function 7 (Light scenes)
Radio sensor detection (e.g. press sensor button)
Activate radio sensor once
LED 1 or 2 blinks orange  radio sensor detected
Function setting (e.g. function 3)
LRN/SET button 3 x activated
LED blinks 3 x orange  function 3
Parameter setting (e.g. parameter 2)
LRN/SET button 2 x activated
LED blinks 2 x green  parameter 2
Button O
Button I
Button O
Button I
Radio sensor Function
Press button I Switch on
Press button O Switch off
Radio sensor Function
Press button Toggle switch state
Parameter
1 Button O is activated
2 Button I is activated
3 Button I and button O are activated
Radio sensor Function
Press button I
Switch on with running time
(parameter)
Press button O Switch off
Parameter
1 2 min running time
2 1 min running time
3 5 min running time
4 10 min running time
5 20 min running time
6 30 min running time
7 60 min running time
8 120 min running time
Radio sensor Function
Press button I Switch on delay (3 minutes)
Press button O Activate running time (parameter)
Parameter
1 6 min delay time
2 2 min delay time
3 10 min delay time
4 15 min delay time
5 20 min delay time
6 30 min delay time
Radio sensor Function
Press button I
or button O
Switch on with running time
(parameter)
Parameter
1 2 min running time
2 1 min running time
3 5 min running time
4 10 min running time
5 20 min running time
6 30 min running time
7 60 min running time
8 120 min running time
Application example: light scene
A light scene can be adjusted by using a radio sensor
and an available light control (various radio actuators
with assigned radio sensors).
Programming
Assign the radio sensor to each radio actuator, program
function 7 and set parameter.
Store light scene (A-D)
• Switch on the required light scene (radio actuators).
• Press button I or O of the radio sensor for longer than
2s. As a conrmation, the lighting switches off and on.
Select light scene (A-D)
Press briefly the button I or O of the radio sensor.
Radio sensor Function (parameter)
Press button O briey Switch on light scene A/C
Press button O long Store light scene A/C
Press button I briey Switch on light scene B/D
Press button I long Store light scene B/D
Parameter
1 button O = light scene A, button I = light scene B
2 button O = light scene C, button I = light scene D
Application example: fan control
Realisation of illumination with fan control by using one
extent
TM
radio actuator (FFA1210) and one radio sensor.
The rst channel is used for fan control and the second
channel for light control.
Programming
• Assign the radio sensor to the rst channel
(fan control), program function 6 and set parameter.
• Assign the radio sensor to the second channel
(light control) and program function 1.
Fan control operation
• Button I will switch the light on. The fan will switch on
after a time delay of 3 minutes.
• Button O will switch the light off. The fan will be
switched off afterexpiration of the running time.
LRN/SET button
long activation
Function programming
(LEDs blinks green rapidly)
Function setting channel 1 / 2
(LED 1 / 2 blinks orange 
number of blinks = function)
Press LRN/SET button
(number = function selection)
Radio sensor detection
( Activate radio sensor once )
CLR/MODE button
press briefly
Parameter setting channel 1 / 2
(LED 1 / 2 blinks green 
number of blinks = parameter)
Press LRN/SET button
(number = parameter selection)
CLR/MODE
button
press briefly
Idle state
(LED off)
Radio sensor Function
Press button Switch on
Release button Switch off
Parameter
1 Button O is activated
2 Button I is activated
3 Button I and button O are activated
4 Button O is activated (pulse time 5s)
5 Button I is activated (pulse time 5s)
6 Button I and button O are activated (pulse time 5s)