User Manual breeva Pro 400 Premium/breeva Pro 400 Please read the instructions carefully before using The appearance of the product is subject to the actual product
Table of content 1. Product description.............................................................01 2. Packing list..........................................................................01 3. Instructions for use.............................................................02 4. UI operation menu..............................................................05 5. How to clean air-purifier....................................................07 6. How to clean the filter....................................
FCC Caution: This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
• Use the device only within the living space and within the stated technical data. Improper use can put health and life at risk. • Children cannot recognize the dangers of using electronic devices. Therefore, be sure to supervise children when they are near a running device. • When operating the equipment, use only the original parts provided. Use this device only at room temperature (>10°C).
• This device contains a license-exempt transmitter/receiver that complies with the Innovation, Science and Economic Development Canada license-exempt RSS standard. The operation is subject to the following two conditions: • This device may not cause interference. • This device must accept any interference, including interference that may cause undesired operation of the device • This device complies with FCC and IC RF radiation exposure limits set forth for an uncontrolled environment.
you are electronics qualified. •Disconnect power before repairing. Do not place in such places: Unstable places. (Otherwise, it may fall over and cause injury) A place of high temperature, high humidity, or easy to get wet. (to prevent leakage accidents) Kitchen or other places where soot is emitted. A place with lots of oil, combustible gases or where leakage may occur. Corrosive gas and metal dust sites. Do not let volatile substances or combustible substances into the machine.
1. Product description This air purifier can strongly remove smoke and dust, and is suitable for places with more smoke, dust, pollen, particles and pollutants in the air, such as indoor smoking. This can reduces the chance of you and your family being harmed by second-hand smoke and haze, and can protect the health of them. This air purifier is equipped with a composite filter which can effectively remove particles in the air and effectively remove the particles of PM2.
3. Instructions for use 3.1 Precautions for filter All filters are attached to the inside of the air purifier. Before using the product, be sure to remove the packaging of the filter. Please follow the procedure in following icons to take out all filters from host and remove their packaging, and then put filters back into the air purifier. 1. Pre-filter 2.
3.2 Steps to attach the filter 1. Place the fingers on the each of left and right hand sides buttons of the machine, press the buttons and the front cover will be automatically opened Button Button 2. Open the front cover towards to your direction 3.
4. Remove all packaging from the filter. 5. Assemble the entire set of filters into the air-purifier in the right order Handle Attention：Make sure that the HEPA activated carbon composite filter with the handle is facing to you, and make sure the all hooks of the filter are properly fitted to the air purifier. 6. Firstly fit the hook at the bottom of the front cover to the bottom of the air purifier, then push it towards to the body of the purifier and fasten it.
4. UI operation menu Button/Light Icon Function Power NO/OFF (Only for breeva Pro 400 premium) Mode Fan speed setting Auto Do Not Disturb Timer Timer Breeva Shield ™ Only for breeva Pro 400 Anion Breeva Shield ™ Only forbreeva Pro 400 premium Anion UV-C Filter Filter replacement reminder and reset Air Quality Air Quality indicator Lock Lock the panel (Only for breeva Pro 400) 4.1 Power Wi-Fi 1. Connecting the power, the power button ‘ ’ light up 2.
4.3 Timer 1. 1. Press the “ ” key 4 for times and set the time with 1/2/4/8H in sequence. When the “ ” key light is on and the 4 lights (1/2/3/4) at the bottom are on respectively, there will be a 'ding' sound. 2. Press and hold the “ ” key for 3 seconds, the“ ”key light will be off and all the 4 lights at the bottom will be off, you will hear a 'ding' to indicate the timing is turned off 4.4.1 UV-C 1.
4.5Filter 1. filter life: When the light is in white, it means that the life of the filter is sufficient; when the light is in yellow, it means that the life of the filter is less than 5%; When the light is in red, it means that the filter life is exhausted, please replace the filter as soon as possible 2. To reset the filter life: Press and hold for 3S, " ", you will hear a 'ding' to reset. 4.6 AQI indicator 1.
5. How to clean air-purifier Note: Always unplug the power plug before cleaning the purifier. Never place the purifier into water or any other liquid. Never use abrasive, caustic, or flammable cleaners (such as bleach or alcohol) to clean any part of the purifier. Only the pre-filter can be washed with water, other filters cannot be washed with water and can not be cleaned by other cleaners. The other filters should only be replaced directly. 7.
different. If TVOC readings are abnormal, place the device away from volatile substances for 24 hours and allow the TVOC to reset 1. Use a soft brush to clean the dust sensor air inlet/outlet 2. Remove the protective cover of the dust sensor 3. Using a slightly wet cotton swab to clean the dust sensor air inlet and air outlet; then dry it with a dry cotton swab.
6. How to clean the filter Note: Only the pre-filter can be washed with water. It is recommended to clean the pre-filter every 30 days to ensure the air-purifier is running under the best performance 1. Please turn off the air-purifier and unplug the power 2. Place the fingers on the each of left and right hand sides buttons of the machine, press the buttons and the front cover will be automatically opened. 3. To remove the pre-filter, take the top two flanges, and pull the filter out towards you 4.
5. Dry the pre-filter with air 6. Put the pre-filter back inside the purifier. Then properly assemble all hooks to the purifier. 7. To install the front cover, firstly assemble the bottom hooks to the bottom of the air-purifier, and then push the front cover towards the air-purifier body.
7 Replace the filter When it is necessary to replace the pre-filter and HEPA activated carbon composite filter, please follow the steps below to correctly replace the new filter. Attention: Activated carbon filter and HEPA filter is not washable or vacuumed by cleaner Make sure that the order you assemble the filter is: HEPA activated carbon composite filter, pre-filter Make sure the filter assembly is attached in the machine in the correct way. 1.
4. Remove all packaging from the filter. 5. The order of replacing new filters (inside to outside) is: HEPA Activated Carbon Composite filter, pre-filter Attention: Make sure the side with the two flanges is facing towards to you and all hooks of the pre-filter are properly fitted to the air-purifier 6. Before installing the filter cover, assemble the bottom hooks to bottom of the purifier.
8 .APP Networking Instructions 1. Download the app You can scan the QR code below through other software to download TCL HOME or search for "TCL HOME" in the APP Store and Google Play store to download and install it. 2. Configuration settings Under the standby state, press and hold the power button for 3 seconds, the buzzer will sound, the Wi-Fi indicator flashes quickly, and the device start the configurable state. When the Wi-Fi indicator is constantly on, the configuration is complete.
3. Voice operation After the configuration is complete, please go to the center page and click on the voice assistant to enter the voice operation settings A. Press the function to start connecting to the voice assistant. B. TCL HOME APP configures both ALEXA and Google voice assistant, you can choose your favorite voice assistant C. The voice operation guidelines will be showing Tips: A. Due to the update of the APP, the actual operation may be slightly different from the above description.
9 Types of malfunctions and solutions This chapter summarizes the most common problems you may encounter when using your air-purifier. If you are unable to resolve the issue based on the information below, please contact the store where you purchased it or customer service center .
Dust sensor is dirty Color of the air quality indicator always the same The filter indicator keep flashing after replacing the filter Inadequate indoor ventilation TVOC sensor is dirty Filter reset button is not pressed properly Please clean the dust sensor Please open the windows to improve indoor air circulation Put the machine in a clean environment for 24 hours Please refer to the description of resetting the filter in section 4.5 of this manual. 1. Turn on the Bluetooth of the 1.
10. Product Specifications Product model breevaPro400/400 Premium Voltage USA:120V~ EU:220-240V~ Frequency USA:50Hz EU:50/60Hz Power 40 W CARD Value ≥380m /h Effective area 26-45 ㎡ 13 Name for each parts 1. Front cover 2. Pre-filter 3. HEPA activated carbon composite filter 4. Host 5. Air outlet 6. Control panel 7.
