Sweeva 3000M/3500M User Manual Thank you for purchasing this product. Please read the user manual carefully before use, and keep it properly.
Thank you for choosing Sweeva 3000M/3500M intelligent robotic sweeper. We hope our product can bring about a better life for you! If you have any questions about the product during use, please call our service hotline: 4006-671-909. Please pay attention to the following basic safety precautions before using the product: * Read the user manual carefully and follow the instructions in the user annual when using the product. * Keep the user manual well for future reference.
Sweeva 3000M/3500M User Manual Table of Contents 1.Safety Instructions………………………….01 Scope of use Safety precautions About child safety About the battery Disclaimers FCC STATEMENT 2.Package Information……………………….04 3.Product Description………………………...05 Main machine Charging Dock (Sweeva 3000M) Self-emptying dustbin(Sweeva 3500M) 4.Installation Instructions…………………….07 Introduction of Main Modules Installation Instructions 5.APP Download and Network Operation…11 6.Operating Instructions……………………..12 7.
Safety Instructions Scope of use * Read the user manual carefully and use the product in accordance with the instructions in the manual to avoid damage due to improper operation. * This product can only be used indoors for the cleaning of wooden floors, ceramic tiles and short-staple carpets. * Do not use the product in high-temperature, humid, flammable, explosive or corrosive environments.
Safety Instructions About the battery 1. Only the batteries provided by the manufacturer are applicable to the product. 2. The battery shall be removed when the product is discarded. 3. Steps to remove the battery: A. Make sure to disconnect the power of the machine when removing the battery; B. Use a screwdriver to remove the bottom screws, and then remove the front bumper and middle shell in turn; C. Take out the motherboard and the battery cover; D.
FCC STATEMENT 1. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference,and (2) This device must accept any interference received, including interference that may cause undesired operation. 2. Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
Package Information Main machine×1 Filter×1 Self-emptying dustbin×1 dust bag×2 Sweeva 3500M Side brush×2 Washable mop×1 Disposable mop×2 * Tip: A high-performance filter has been installed in the main machine.
Product Description Main machine Cleaning/On/Off button • Press once: Start cleaning/pause • Press and hold for 3 seconds: Turn on/off the machine • Press and hold for 10 seconds to force restart in the dead state Recharge button • Press once: Return for recharge • Press and hold for 10 seconds: Restore factory settings Recharge button + Cleaning/On/Off button • Press and hold the two buttons simultaneously for 3 seconds: Enter the network configuration mode Power indicator • Solid white light: standby/(nor
Charging Dock (Sweeva 3000M) • Charging dock indicator Normally on: When the main machine is not connected to the charging dock Off: Power off or the main machine and the charging dock are correctly connected Self-emptying dustbin (Sweeva 3500M) • Self-emptying dustbin indicator White light normally on: When the main machine is not connected to the Self-emptying dustbin White light off: The main machine and the Self-emptying dustbin are correctly connected Red light normally on: The dust bag is not in p
Introduction of Main Modules Front cover Middle shell Dust box Filter screen opening Button Front bumper Recharge sensor Recharge sensor Charging pole pieces Dust box release button Dust collection port Water tank Wall sensor Dust box opening Anti-drop sensor Side brush Charging electrode Universal wheel UV-C lamp Wheel Rolling brush Dust box Filter screen opening Rolling brush protective cover Filter Warning: Take care to avoid direct exposure to human eyes with the UV-C lamp.
Introduction of Main Modules Top cover Open the top cover to put in/take out the dust bag Fan filter Dust bag compartment Recharge and dust collection sensor Dust bag handle Charging pole pieces Dust bag Vacuum port Vacuum the garbage in the main machine into the dust bag through the vacuum port
Installation Instructions Installation of Sweeva 3000M charging dock • Connect the charging dock with the power adapter, and be sure to organize the adapter cable to prevent the robotic vacuum cleaner from being entangled during cleaning. • Place the charging dock against and perpendicular to the wall on a level, hard floor, without obstacles within 1.5m in front and 0.5m on the left and right.
• Remove the protective strip Before use, remove the protective strips on both sides of • Install the side brush • Startup and charging For initial use, press and hold the “ ” button for 3 seconds to turn on the machine The main machine needs to be fully charged (approximately 4 hours) to ensure normal operation. Orange light Side brush installation: Align with the holes and press gently to fix the side brush on the machine.
APP Download and Network Operation Download Search for “ TCL Home ” in the mobile app store or scan the QR code below to download the APP. Look at the picture below. The QR code on the left is for Sweeva 3000M; The QR code on the right is for Sweeva 3500M. * If the main machine cannot be connected in the 2.4/5GHz dual-band Wi-Fi network, please switch to the 2.4GHz network for Wi-Fi settings. After the setting is completed, you can switch back.
Operating Instructions Power on/off Press and hold the Press and hold the button for 3 seconds to turn on the machine. button for 3 seconds to turn off the machine. Start cleaning Press the button to start the automatic cleaning mode. After starting, the robotic vacuum cleaner will leave the charging dock or the self-emptying dustbin, then delineate an area of 4m×4m, and first conduct cleaning in a “bow” shape and complete the cleaning along the wall.
Use of the mopping assembly • Installation of the wet mopping assembly Take out the two-in-one dust box and water tank assembly Take out the dust box Open the rubber plug and add water to the water tank from the water injection port. Install the mop on the mop holder. After drying the water spilled or attached to the surface, put the two-in-one dust box and water tank assembly back into the machine, and make sure it is installed in place.
* Do not use the mopping mode on the carpet. * When the robotic vacuum cleaner is in the charging state or idle, remove the mop holder, and the water level can not be set in the APP at this time. * To achieve better mopping, it is recommended to use the main machine to clean the floor three times before installing the mopping module. * To avoid damaging the wooden floor, please make sure to take out the mopping assembly immediately after the main machine finishes mopping.
Daily Maintenance Clean the dust box Empty the dust box, put the dust box close to the trash can, and tap the dust box gently to knock off the excess dirt. Take out the high-performance filter, and clean the filter with the supplied cleaning brush. The water tank, dust box and filter screen assembly can be thoroughly rinsed with water as needed (Note: The filter cannot be cleaned with hot water or detergent). After cleaning the water tank, dust box and filter screen assembly must be thoroughly air-dried.
Clean the universal wheel As hair is entangled on the universal wheel or dust particles adhere to it easily, be sure to clean the universal wheel regularly or as needed. Pull the universal wheel upwards. Clean up the hair or debris entangled around the universal wheel or in the chamber of the universal wheel. Reinstall the universal wheel and push it in until it clicks into place.
Clean the charging electrode Please clean the charging electrode regularly, and wipe off the dust on the charging electrode with a soft dry cloth or cleaning brush. Transparent cover of the dust channel Charging dock (Sweeva 3000M) Dust channel Charging electrode Replace the dust bag Self-emptying dustbin (Sweeva 3500M) When the dust bag is full, the Self-emptying dustbin indicator flashes in red to remind you to replace the dust bag in time.
Common Faults Cause and Solution Fault Startup failure Charging failure Recharge failure 1. If the battery power is low, please place the main machine on the charging dock or the self-emptying dustbin and align with the charging pole piece, then press and hold for 3 seconds, and the main machine will automatically turn on (when completely out of power, it will take a while to automatically turn on) 2.
Cause and Solution Fault 1. Please check whether the self-emptying dustbin and charging dock is normally powered on. When the cleaning time is more than 5 minutes, the main machine will automatically return for recharge. After recharge, automatic dust collection will start; 2.
List of Faults When the main machine fails, the red indicator light on the main machine will flash, and the relevant Buzzer prompt will be heard at the same time. Fault description Buzzer tone Solution Please open the battery compartment and check whether the battery is properly connected, and restart the machine. When the battery temperature is too high or low, please wait until the battery temperature is normal (0 40 /32° 104°F) before using.
Technical Specifications Functional parameters of the main machine Operating voltage 14.4V Battery Lithium battery Operating hours Approx.180min(standard level) Operating humidity range 90 RH Noise 68dB(standard level) Dimensions Functional parameters of the main machine Power adapter and Charging dock 100-240 V AC 0.5A MAX 19V 0.6A Input voltage Input current Output voltage Output current Self-emptying dustbin 342*78.
Environmental Statement(Optional) Names and contents of harmful substances in the product Harmful Substances Component Name Lead Mercury Cadmium (Pb) (Hg) (Cd) Hexavalent Polybrominated chromium biphenyl (Cr (VI)) (PBB) Polybrominated diphenyl ethers (PBDE) Shell component Internal plastic parts Metal parts X Electrical components and control components X Dry batteries X Rechargeable batteries X X This form is prepared in accordance with the provisions of SJ/T 11364.
Warranty Card II Warranty Card I User name User name Address Address Tel. Tel. Postal code Postal code Product model Product model Purchase date Purchase date Invoice number Invoice number Warranty period Warranty period Product warranty description: 1. From the date of the user’s purchase of this product, the warranty period is one year for the host machine, and six months for the adapter, rechargeable batteries and other accessories. 2.
