Quick Start Guide CJBXXXXALAAA 1
www.sar-tick.com This product meets applicable national SAR limits of 1.6 W/kg. The specific maximum SAR values can be found in the Radio Waves section of this user guide. When carrying the product or using it while worn on your body, either use an approved accessory such as a holster or otherwise maintain a distance of 10 mm from the body to ensure compliance with RF exposure requirements. Note that the product may be transmitting even if you are not surfing the Internet.
Switch off your device when on an aircraft. The device may cause interference to aircraft control signals. Switch off your device near high-precision electronic devices. The device may affect the performance of these devices. Do not attempt to disassemble your device or its accessories. Only qualified personnel are allowed to service or repair the device. Do not place your device or its accessories in containers with a strong electromagnetic field. Do not place magnetic storage media near your device.
CHARGERS Main powered chargers will operate within the temperature range of: 0°C to 40°C. The chargers designed for your device meet with the standard for safety of information technology equipment and office equipment use. Due to different applicable electrical specifications, a charger you purchased in one jurisdiction may not work in another jurisdiction. They should be used for this purpose only.
Application PC PAD LinkZone Smart phone Getting to Know Your Device Power key WPS key LED indicator USB jack 5
LED Description Part Description Power key Hold the “Power” key for 3 seconds to power the device on/ off. WPS key Hold “WPS” key for 3 seconds to activate the WPS function. Once activated, the Wi-Fi LED indicator will flash every two seconds. If the network is not accessed within 2 minutes device will automatically exit WPS mode. LED indicators Displays signal, Wi-Fi, SMS, and battery charge status.
Part Description Power saving mode • If no buttons are pressed for a period of 30 seconds, all LED lights will turn off automatically. Press any button, charge device, or connect to a computer, to turn on LED lights again. • If no Wi-Fi is accessed for a period of 10 minutes, network dialing ceases automatically. Press any button, or access the device, to turn on Wi-Fi again. • If no Wi-Fi is accessed for a period of 30 minutes, the Wi-Fi AP function will turn off automatically.
Network Indicator (Red or Blue LED) Wi-Fi Indicator (Blue LED) SMS Indicator (Blue LED) Battery Indicator (Red or Blue LED) LED Description Solid Blue Registered and connected to network. Flashing Blue Network disconnected. Solid Red No network, no SIM card or SIM card error, limited or no service. Wi-Fi Solid Blue Wi-Fi is active. SMS Solid Blue New message Flashing Blue Message inbox is full.
Turning On Your Device Step 1: Remove back cover: Slot Note: Find the slot on the front cover to open.
Step 3: Install battery: Step 4: Close back cover: Position the back cover so that locating nub is inserted into corresponding indentation (please refer to illustration below) Step 5: Power device on: Long Press the “Power” key until all LED indicators illuminate in blue. Connecting in Wi-Fi mode SSID: locate the SSID information on the sticker on the Back Cover. Step 1: Use the Wi-Fi manager on the Wi-Fi embedded device to select network name (SSID).
Choose SSID from the list of available networks. • From a Mac computer: Select System Preferences -> Network -> Airport. Click “Advanced” to choose SSID from the list of available networks. • From an iOS device: Settings -> Wi-Fi. Choose SSID from the available networks. • From an android device: Settings -> Wireless controls -> Wi-Fi settings. Choose SSID from the available networks. Step 2: Enter the Wi-Fi key when prompted for a security key.
Leaflet. Open LINK APP by entering the password. Note: Default password is admin Set the WiFi network name & WiFi password. Save the settings & restart network connection. Charging Your Device You have two ways to charge your device. Wall Charger: Connect USB cable with Charger head and device, then charging begin. When the device is powered off, charging will take a maximum of 3 hours. USB Charger: You can also charge the device by connecting it to a PC with the USB cable.
part of comprehensive guidelines and establish permitted levels of RF energy for the general population. The guidelines are based on standards that were developed by independent scientific organizations through periodic and thorough evaluation of scientific studies. These guidelines include a substantial safety margin designed to ensure the safety of all persons, regardless of age and health. The exposure standard for routers employs a unit of measurement known as the Specific Absorption Rate, or SAR.
Use of other accessories may not ensure compliance with FCC RF exposure guidelines. Additional information on SAR can be found on the Cellular Telecommunications & Internet Association (CTIA) Web site: http://www.ctia.org/ The World Health Organization (WHO) considers that present scientific information does not indicate the need for any special precautions for use of routers.
- Consult the dealer or an experienced radio/ TV technician for help. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. For receiver devices associated with the operation of a licensed radio service (e.g. FM broadcast), they bear the following statement: This device complies with Part 15 of the FCC Rules. Operation is subject to the condition that this device does not cause harmful interference.
Fi features, only connect to trusted Wi-Fi networks. Also when using your product as a hotspot (where available), use network security. These precautions will help prevent unauthorized access to your device. Your product can store personal information in various locations including a SIM card, memory card, and built-in memory. Be sure to remove or clear all personal information before you recycle, return, or give away your product.
Licenses The Wi-Fi Logo is a certification mark of the Wi-Fi Alliance. • FCC Compliance(FOR PART 15B/PART 15C) FCC ID: 2ACCJB132 Warranty The device is warranted against any deviation from technical specifications for a period of twelve (12) (1) months from the date specified on your original invoice. Under the terms of this warranty, you must immediately inform your vendor in case of a conformity defect on this device, and present a proof of purchase.
humidity, infiltration of liquids, inclement weather, 5) Connecting to or integrating into this device any equipment not supplied or not recommended by the manufacturer, 6) Any servicing, modification or repair performed by individuals not authorized by the manufacturer, the vendor or the approved maintenance center, 7) Use of this device for a purpose other than that for which it was designed, 8) Malfunctions caused by external causes (e.g.
