Instruction Manual
USE 90 PSI MAXIMUM
Ref #
Part # Description
Qty.
8030G01
8030G02
8030G03
8030G04
8030G05
8030G06
8030G08
8030G12
8030G13
8030G14
8030G15
8030G16
8030G17
8030G18
8030G19
8030G20
8030G21
8030G22
8030G23
8030G24
8030G25
8030G26
8030G27
8030G28
8030G29
8030G30
8030G31
8030G32
8030G33
8030G34
Throttle Lever
Lever Pin
Motor Housing
O-Ring
Valve Stem
O-Ring
Regulator
Lock Nut
O-Ring
Housing
O-Ring
Bearing
Front End Plate
Spacer
Key
Rotor
Rotor Blade (set of 5)
Cylinder
Rear End Plate
Bearing
O-Ring
Motor Nut
Handle
Cap Screw
Handle Bracket
Finger Plate
Adjust Screw
Guard Body
Guard
Roll Pin
505 N. Railroad Ave. 33435
P.O. Box 1117 33425
Boynton Beach, Florida
Ph. (561) 732-1111
Fax (561) 731-4412
Toll Free 800-805-8665
Ref #
Part # Description
Qty.
8030G34
8030G36
8030G37
8030G38
8030G39
8030G40
8030G41
8030G42
8030G43
8030G44
8030G45
8030G46
8030G47
8030G48
8030G49
8030G50
8030G51
8030G52
8030G53
8030G54
8030G55
8030G56
8030G57
8030G58
8030G59
8030G60
8030G61
8030G62
8030G63
LockNut
Drive Pulley
Dust Cover
Cover Latch
Cap Screw
Washer
Stopper
Spring
Roll Pin
Stopper Pin
Tension Spring
Tension Arm
Bolt
Idler Shaft
Idler Pulley Assembly
Collar
Bearing
Lock Nut
Shoe
Silencer
O-Ring
Air Deflector
Air Inlet
Sanding Belt
Seal
Valve Stem
Spring
O-Ring
Snap Ring
For Warranty Information &
Warranty Registration Visit
www.taylorpneumatic.com
1022 TPTC /all rights reserved /COPYRIGHT 2022 / final
T-8030G Belt Sand
er
1-3/16” X 21 1/4”
Uses Sanding or Surface Prep Belts
OILING INSTRUCTIONS:
OIL AFTER EACH USE WITH
FEW DROPS OF AIRTOOL OIL
THROUGH THE AIR INLET. RUN
FOR ONE SECOND TO COAT
ALL INTERNAL PARTS
1
2
3
4
5
6
8
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
5
1
1
1
1
1
1
1
1
1
1
1
2
1
1
1
1
1
1
1
1
1
1
2
1
1
1
1
1
1
1
1
1
1
1
1
1
1set