V32MCAK E01-01EN 11/13/2007_ver.A-PD.paula Table of Contents OPERATING SAFETY .....................................................................................................1 CONNECTING ...............................................................................................................2 English BEFORE GETTING STARTED.....................................................................................1 Function Keys........................................................................
PICTURE SETTING ......................................................................................................23 SOUND SETTING.........................................................................................................24 SERVICE IN ANALOGUE TV..........................................................................................25 Service Management ...........................................................................................26 Rename/Sort/Delete........................
V32MCAK E01-01EN 11/13/2007_ver.A-PD.paula Before Getting Started English Please read through this section carefully and follow the instructions to maximize the reliable operation and lifetime of your LCD display. Always keep these instructions handy and close by your LCD display. Keep the instructions and the packaging so that if you sell or give away your LCD display you can give them to the Français new owner. Conventions used in this manual Italiano complete a task.
Contact the Call Centre immediately in any of the following situations. Do NOT plug in or switch on your display: • If the power cable/power supply overheats or is damaged • If liquid is leaked into the monitor If the LCD display is dropped or the housing damaged • Connecting Observe the following instructions to connect your LCD display properly: Power supply • Do not open the power supply housing. An open housing presents a lethal hazard from electrical shock.
V32MCAK E01-01EN 11/13/2007_ver.A-PD.paula Additional Safety Instructions When using any electronic equipment, basic safety precautions should always be • Do not use this product including TV set and remote near water (e.g. near a bathtub, wash bowl, kitchen sink or laundry tub, in a wet basement or near a English taken. Following the guidelines below can reduce the risk of fire, electric shock and injury to person: instructions. Français swimming pool).
Introduction Thank you for purchasing our LCD display. We thank you for your confidence in our products and are pleased to greet you as a new customer. We focus on great features, ease of use and reliability in manufacturing your LCD display. Service Your display comes with a one-year warranty; this is in addition to your statutory rights. This manual contains a separate chapter on Troubleshooting on page 37.
V32MCAK E01-01EN 11/13/2007_ver.A-PD.paula Further Features ¾ The connection terminals include RF IN, D-SUB, HDMI1, HDMI2, SCART 1 English (CVBS, RGB), SCART 2 (CVBS, S-VIDEO, RGB), COMPONENT, CVBS and S-VIDEO. ¾ Easy-to-use remote control, and OSD (On-Screen Display) menu. Français ¾ ARC (Aspect Ratio Control) settings include Auto image, 4:3, 16:9, 14:9, Panoramic, and Zoom. ¾ APC (Automatic Picture Control) settings include Normal, Cinema, and Dynamic. Italiano ¾ A.P.S.
Overview of the TV Indicator Indicator Remote control sensor Indicator Indicator Lighting Status: OFF (No power input) Off Standby passive Red Power on (TV / Video / PC mode) Green Standby active (only available in PC mode) Amber A green indicator lights when the power is on and an amber indicator lights when in the standby PC mode. A red indicator lights when in standby mode passive.
V32MCAK E01-01EN 11/13/2007_ver.A-PD.paula Deutsch Italiano Français English Function Keys Function Keys (on the display panel): • Select the TV display mode to switch Auto Image / Panoramic / 16:9 / 14:9 / 4:3 / Zoom. • When in OSD (On-Screen Display)* menu, press EXIT / ARC to close the OSD menu • Increase or decrease the volume. Nederlands - VOLUME + ▼CHANNEL▲ • Change channels. MENU • Display the OSD main menu. • Return to previous menu when in OSD menu.
Connections NOTE: Audio out L/R: The level of audio output cannot be changed using the volume control on your display. This connector should be used with an external audio amplifier that can be used to control the volume.
V32MCAK E01-01EN 11/13/2007_ver.A-PD.paula Overview of the Remote Control 3 English Français 2 Power Shift the TV on or off. TELETEXT Press the button to show the TELETEXT Service. Toggle text modes between TEXT / MIX / PAT / OFF INDEX ATV (analogue): Return to Page 100 (TELETEXT reset). Italiano HOLD Press “HOLD” button to stop the automatic TELETEXT page change. INTERRUPT Press “INTERRUPT” button to switch to TV while waiting for the required text page.
ARC (Aspect Ratio Control) In VGA (PC) mode, to toggle the picture mode between 16:9 / 4:3. In Video mode, to toggle the picture mode between Auto Image / Panoramic / 16:9 / 14:9 / 4:3 / Zoom 10 EXIT In OSD screen, to exit a menu or sub-menu. 11 OK In OSD screen, to set up a function or enter a sub-menu. ▲/►/▼/◄ OSD screen in ATV (analogue): to access menu items. 12 MENU Display the On-Screen Display (OSD) menu or return to a layer of menu. 13 TV Select the TV mode.
V32MCAK E01-01EN 11/13/2007_ver.A-PD.paula Setting Up Connecting video devices via AV cables Nederlands Español Deutsch Italiano This TV accepts different Video Inputs. Connecting to device connectors with better video quality will bring you better viewing enjoyment. The video quality sequence from the best to a normal one would be Component, SCART, S-VIDEO, and CVBS. Français English Connections NOTE: • ANT IN: Antenna (aerial) In. • Connecting cables above are not supplied.
Connecting a video device via HDMI - HDMI This can be applied only if there is an HDMI Output connector on the external device. video devices NOTE: • Video Device: DVD Player, Set-top Box, Game Box…etc. • HDMI: High-Definition Multimedia Interface • No audio cable is needed when via HDMI to HDMI connection. • Either HDMI1 or HDMI2 can work when you connect one video device. • Connecting cables above are not supplied.
V32MCAK E01-01EN 11/13/2007_ver.A-PD.paula Nederlands Español Deutsch Italiano Français English Connecting a PC via VGA cable NOTE: • To receive a display, connect a VGA cable between the D-SUB connector on the TV and the VGA connector on a PC. • To receive a sound, connect an audio cable between the PC AUDIO IN jack on the TV and AUDIO OUT jack on a PC. • Connecting cables above are not supplied.
Watching TV Turning the LCD Display On and Off Turning On After the LCD DISPLAY is connected, you can then turn on your LCD DISPLAY. Follow the instructions below to turn the display on: Step 1: Place supplied two (AAA) batteries into the remote control; make sure the batteries are oriented correctly. Step 2: Connect the power cord into the AC IN located in the back of the display and the other end to the power outlet on the wall.
V32MCAK E01-01EN 11/13/2007_ver.A-PD.paula Français English Step 3. Press the POWER button on the right side of the display, or press the POWER button of the remote control to swift on the display. The indicator will light up green. Deutsch Italiano green If you go away for a few days or will not use your TV for a long period of time, please unplug the power cord to turn the main power off.
Initial Power on When you switch on the TV for the first time, the Auto Install menu will appear automatically on the screen. (Please ensure your TV has aerial cables connected.) The whole Auto Install process will take around 10 minutes to complete. 1. 2. Press S or T to highlight Country* and then press OK. Press W or X to choose your country in the Message Bar, then press OK. 3. Press S or T to highlight Language*, then press OK to enter the Adjustment Bar. 4. Press W or X to choose your language.
V32MCAK E01-01EN 11/13/2007_ver.A-PD.paula Source Buttons English 1. Turn on the power. Italiano Français 2. Select an input source as described below.
Volume Control Using Volume Control Press VOL+ / VOL- to increase or decrease the sound volume. Using Mute At any time, users can temporarily turn off the sound by pressing the MUTE button. 1. Press MUTE and the sound cuts off. 2. Press MUTE again or VOL+ / VOL- to turn the sound back to the previous level. Setting the Sleep Timer You can set the Sleep Timer to turn off the TV automatically. The timer can be set from 00 to 120 minutes in 10 minute intervals. 18 1.
V32MCAK E01-01EN 11/13/2007_ver.A-PD.paula 14:9 : In this mode, will display 14:9 broadcasts in the correct proportions. There will be black strips at both sides of the screen. 16:9 : This mode expands the width of 4:3 broadcasts evenly to fill the 16:9 screen. PANORAMIC : Expands 4:3 broadcasts to fit the 16:9 screen by expanding the image at the edges of the screen. This creates less distortion at the centre of the screen.
NICAM/A2 (IGR) Broadcast Selection Depending on the particular program being broadcast, you can press the SOUND button to listen to different language sources. Under different systems, broadcast function will show differently. Sound A : sends the primary broadcast language to the loudspeakers. Sound B : sends the secondary broadcast language to the loudspeakers.
V32MCAK E01-01EN 11/13/2007_ver.A-PD.paula General Controls & Adjustment How to control On-Screen Display (OSD) 2. You can also use the buttons of the display to open the OSD main menu and adjust different settings for your TV. Français You can use the remote control buttons to open the OSD main menu and change the settings for the TV. Nederlands Español Deutsch Italiano 1. English OSD main menu can appear by pressing buttons either on remote control or the right side of the TV.
Viewing the On-Screen Display (OSD) Main menu Instruction (Message bar) Use the left / right arrow buttons on the remote to select the menu option ICON. Then use the up / Down arrow button on the remote to move down the Sub menu items. Press the OK button to select the option. Sub-menu Please press OK on the remote control, after selecting your preferred item in sub-menu. How to use main menu and sub menu in OSD 1. 2. 3. 4. 5. 6. 22 With the power on, press MENU on the remote.
V32MCAK E01-01EN 11/13/2007_ver.A-PD.paula Picture Setting You may need to perform separate adjustments for brightness and contrast for the different modes. English With the power on, in any mode. 1. Press Source button to choose desired source. 2. Press MENU. 3. Press W or X to select “Video” and press T. Français 4. Press S or T to highlight one item. Press OK to enter the Sub-menu. 5. Press W or X to make adjustments in the adjustment bar and press OK. 6.
Sound Setting With the power on, in any mode. 1. Press Source button to choose desired source. 2. Press MENU. 3. Press W or X to select “Audio” and press T. 4. Press S or T to highlight one item. Press OK to enter the Sub-menu. 5. Press W or X to make adjustments in the adjustment bar and press OK. 6. Press MENU to return to Main menu, or press EXIT to exit the menu. Audio: Surround Modes:You can choose different audio effects for your TV.
V32MCAK E01-01EN 11/13/2007_ver.A-PD.paula Service in Analogue TV With the power on, in Analogue TV mode. English 1. Press TV of Source Button to select TV mode. Press MENU. 2. Press W or X to select “Service” and press T. 3. Press S or T to highlight one item. Press OK to enter the Sub-menu. Français 4. The operating screens will vary due to different functions; refer to the Message Bar below to adjust to your favourite settings. 5. Press OK to confirm your setting. Italiano 6.
Service Management Rename/Sort/Delete With the power on, in Analogue TV mode. 1. Press TV to select TV mode. Press MENU. 2. Press W or X to select “Service” and press T. 3. Press S or T to highlight “Service Management”. Press OK to enter the sub-menu. 4. Press T to highlight “Rename”. Press OK to enter the Service Naming. 5. In the Service Naming, press S or T to select the programme you want to rename, and then press OK to edit name. 6.
V32MCAK E01-01EN 11/13/2007_ver.A-PD.paula Preferences With the power on, in any mode. 1. Press Source button to choose your desired source. English 2. Press MENU. 3. Press W or X to select “Preferences” and press T. 4. Press S or T to highlight one item. Press OK to enter the Sub-menu. Français 5. Press S or T to highlight one item. Press OK. Press W or X to make adjustments, then press OK again. 6. Press MENU to return to Main menu, or press EXIT to exit the menu.
Child Lock With the power on, in any modes, except for Analogue TV. 1. Press Source button to choose your desired source. 2. Press MENU. 3. Press W or X to select “Preferences” and press T. 4. Press S or T to highlight “Child Lock” and press OK. 5. Press W or X to change the current status. 6. Enter your preferred PIN (Personal Identification Number) by using numeric buttons (0~9). To exit the menu, press EXIT.
V32MCAK E01-01EN 11/13/2007_ver.A-PD.paula On Timer With the power on, in any mode. 1. Press Source button to choose desired source. English 2. Press MENU. Français 3. Press W or X to select “Preferences” and press T. 4. Press S or T to highlight “On Timer”. Press OK to enter the Sub-menu. 5. Press T to highlight “TV on after”. Press OK to set up time. 6. Enter desired hours/minutes* by using numeric buttons (0~9), press OK. Nederlands Español Deutsch Italiano 7.
Connectivity: PC / SCART Setting With the power on, in VGA mode. 1. Press PC/HD of source buttons to select VGA mode. 2. Press MENU. 3. Press W or X to select “Connectivity”. 4. Press T to highlight “PC”, and then press OK to enter the Sub-menu. 5. Press S or T to highlight one item. Press OK. 6. Press W or X to make adjustments, then press OK. 7. Press MENU to return to the Main menu, or press EXIT to exit the menu.
V32MCAK E01-01EN 11/13/2007_ver.A-PD.paula Resolution Adjustment This message of your current PC resolutions and frequency appears, when PC is Italiano Français English connected. With the power on, with PC connected. Deutsch Press S or T in the remote control to highlight one item. Press OK in the remote control. Note: 1. The picture of “Wide mode selection” will appear in some specific PC resolutions Español of 1024x768, 1280x768 1360x768 and 640x350, 720x400. Nederlands 2.
Information With the power on, in any mode. 1. Press Source button to choose desired source. 2. Press MENU. 3. Press W or X to select “Information”. 4. Press OK or MENU or EXIT to exit the menu. You can also use the “SUB-TITLE” key on remote control to invoke the “Information.” Information: Panel Res. : Displays the panel resolution of the TV. Main Source : Displays the source of the main picture source. Main Format : Main picture input format. Sound Mode : Displays the sound mode information.
V32MCAK E01-01EN 11/13/2007_ver.A-PD.paula Reset With the power on, in any mode 1. Press MENU. English 2. Press W or X to select “Service” and press T. 3. Press S or T to highlight “Reset”. Press OK then finished. Français 4. If you want to exit the menu, press EXIT.
TELETEXT TELETEXT is an information service broadcast offered by some TV stations (depending on different countries) which gives up-to-the-minute information, news, weather, television programs, share prices, subtitles, and so on. This TV has 100 Teletext page number memories. TELETEXT Operation Step1. Select a TV station on which TELETEXT is being transmitted. Step2. Press TELETEXT on the remote to make the TELETEXT screen appear.
V32MCAK E01-01EN 11/13/2007_ver.A-PD.paula TELETEXT Page Selection Step1. Enter the required TELETEXT page as a three digit number. Display : The selected page number is displayed at the top left corner of the screen. located, so that the desired page is displayed on the screen. Step2. The CH▼▲button can be used to select the preceding or following page. Step3. Fastext movement by the 4 coloured buttons on the remote.
TIME Step1. While watching a TV program with TELETEXT transmission, press the button. The current time information will be displayed on the upper centre corner of the screen. Step2. The time information will disappear after pressing the button again. Sub-Page Press the button to stop the running teletext page and enter your subpage number.
V32MCAK E01-01EN 11/13/2007_ver.A-PD.paula Here are some tips to solve some common problems. If your problem still exists, please contact your nearby retailer directly. Make sure the input mode is set correctly. Italiano Make sure the power cord is properly connected. Español Deutsch Français There is no picture and sound. English Troubleshooting Make sure the Contrast/ Brightness is properly adjusted. Make sure all external devices are connected properly.
There is no picture or sound, just noise. The reception may be weak. Make sure the aerial is not disconnected. The picture is not clear. The reception may be weak. Make sure the aerial is not disconnected. The picture is too bright. Check Contrast/Brightness adjustment. Check the APC (Auto Picture Control) function setting. Check the APC function setting. Check Contrast/Brightness adjustment. Make sure the TV set isn’t near microwave oven or other equipment.
V32MCAK E01-01EN 11/13/2007_ver.A-PD.paula Make sure the aerial is facing the right direction. There may be reflected signals from mountains or buildings. There may be interference from automobiles, trains, high voltage lines, neon lights, etc. Français English The picture has double or triple image. Deutsch Italiano The picture is spotty. Check the batteries in the remote control are not flat. Make sure the remote control sensor of TV set is not under strong lighting.
Safety and Regulatory Information Repair • Leave all repairs of your LCD display to authorised and qualified personnel only. • Should a repair be necessary, please contact one of our authorized service partners only. Notes for Service Engineers • Before opening the housing, disconnect the product from all power sources and remove any connecting cables. If the display has not been disconnected from the power outlet before being opened, there is a danger to life through electric shock.
V32MCAK E01-01EN 11/13/2007_ver.A-PD.paula VGA 60HZ 31.469 － 640*480 59.941 － SVGA 60HZ 35.16 ＋ 800*600 56.25 ＋ SVGA 60HZ 37.879 ＋ 800*600 60.317 ＋ XGA 60HZ 48.363 － 1024*768 60.004 － XGA 70HZ 56.476 － 1024*768 70.069 － MAC VGA 35.0 － 640*480 66.667 － US TEXT 31.469 － 720*400 70.087 ＋ 9 WXGA 1280*768 47.73 － 60 － 10 WXGA 1360*768 47.7 + 60 + 2 3 4 5 6 7 8 25.175 800 640 48 96 449 350 60 2 25.175 800 640 48 96 525 480 33 2 36.
Specifications Screen Size (diagonal) 32’’ Audio Output 10W x 2 Aspect Ratio 16:9 TV System PAL / SECAM Video Playback PAL / SECAM / NTSC Sound System NICAM / A2 (IGR) Panel Resolution 1366 x 768 (WXGA) Antenna In, HDMI1,HDMI2, Component In (YPbPr), Composite In, Audio In(L/R), Connectivity D-SUB, PC Audio in, SPDIF SCART1,SCART2, S-Video Power Supply AC 100V~240V, 50/60Hz Power consumption 160 W 1W Standby power consumption Width 675 mm Set dimensions (with stand) Height 527 mm Dept
