Installation Guide

ManualsBrandsTASCAM ManualsOtherTASCAM TASCAM Dante module

Table Of Contents

Dante module firmware update procedures

Dante module update manual

TASCAM Dante module update manual 1

0220.MA-3034B

Dante module firmware update procedures

The firmware for the TASCAM products Dante module installed in the unit can be updated using an application installed on a computer

connected to the Primary network.

Please download the latest applications compatible with the computer operating system from the Audinate website links below and

install them on the computer before starting the firmware update.

p Dante Firmware Update Manager

https://www.audinate.com/products/firmware-update-manager

p Dante Controller

https://www.audinate.com/products/software/dante-controller

Checking the Dante module firmware version

1. When Dante Controller is launched, the screen shown

below will open.

The device name will appear if the computer and the Dante

device are connected properly.

To check the version of a device, double-click its name.

2. Click the “Statues” tab.

The version number is shown below framed in red (

Updating is not necessary if the number shown here is the

same or newer than the firmware version you intend to use

for the update.

Dante module firmware update procedures

1. Download the latest firmware from the TEAC Global Site

(http://teac-global.com/).

If the downloaded file is in ZIP format or another

compressed file type, decompress it.

2. After downloading and decompressing the latest Dante

update file, copy it to any directory.

(For example, copy it to the desktop.)

3. Use a LAN cable to connect the computer Ethernet port and

the unit Ethernet port.

4. Launch the Dante Firmware Update Manager installed on

the computer.

After launching, the following screen will appear. Click the

“Next” button.

Contents

Dante module firmware update procedures ............................................................................................................................................. 1

Checking the Dante module firmware version .............................................................................................................................................................................1

Dante module firmware update procedures .................................................................................................................................................................................1

Recovery procedures if a failure occurs during Dante module firmware update .............................................................................................................4

Using Dante Controller to update Dante firmware ......................................................................................................................................................................6

Downloading the updater ....................................................................................................................................................................................................................7

Summary of content (7 pages)

PAGE 1
Dante module update manual Contents Dante module firmware update procedures ............................................................................................................................................. 1 Checking the Dante module firmware version .............................................................................................................................................................................1 Dante module firmware update procedures ..................................
PAGE 2
Dante module update manual 5. Click the “Update Dante Firmware” button. 6. Click the “Browse” button. Then, select and open the file copied in step 2. Click the “Next” button. 8. When the text framed in red ( ) becomes “XX matching devices found (of YY total)”, put a check (4) next to the Dante device you want to update, and click the “Start” button. 9. Click the “OK” button. Clicking the “OK” button starts the Dante module firmware update.
PAGE 3
Dante module update manual 14. When Dante Controller is launched, the screen shown below will open. The device name will appear if the computer and the Dante device are connected properly. Double-click the name of the device that you just updated. 15. Click the “Status” tab, and confirm that the version numbers framed in red ( ) are the latest, completing the update.
PAGE 4
Dante module update manual Recovery procedures if a failure occurs during Dante module firmware update If an update fails while underway because, for example, the app was forcibly quit or the network connection was interrupted, the name of the device will appear red in Dante Controller to show that it is in fail-safe mode. The following procedures must be conducted to recover. 1. Launch Dante Controller. Double-click the name of the Dante device shown in red.
PAGE 5
Dante module update manual 7. Launch Dante Controller, and confirm that the name of the updated device appears black, showing that it has been recovered.
PAGE 6
Dante module update manual Using Dante Controller to update Dante firmware Follow the procedures below to use Dante Controller to update Dante firmware. NOTE If the Dante network is not connected to the Internet, first follow the procedures in “Downloading the updater” on page 7. 1. Launch Dante Controller. Left-click the icon in the red box ( Updater. 2. Open “UPDATE(S) AVAILABLE” in Dante Updater and check ) to launch Dante the availability of updates.
PAGE 7
Dante module update manual 5. When the update completes, the following pop-up will appear. Since restarting the device is necessary, put a check next to “REBOOT REQUIRED”. Then, left-click “REBOOT SELECTED DEVICES” at the bottom left. 7. After the device has restarted, it will appear in the UP-TODATE section of Dante Updater. 6. When the device restarts, the following pop-up will appear. Left-click “CLOSE” at the bottom right. This completes the procedure.