Notebook Preface Regulations Information II
Notebook Preface Safety Guideline for Using Lithium Battery (Danish) ADVARSEL! håndtering. Lithiumbatteri --- Eksplosionsfare ved fejlagtig Udskiftning må kun ske med batteri af same fabrikat og type. Levé det brugte batteri tilbage til leverandøren. (Deutsch) VORSICHT: Explosionsgefahr bei unsachgemäßem Austausch der Batterie. Ersatz nur durch denselben oder einen vom Hersteller empfohlenen gleich-wertigen Typ. Entsorgung gebrauchter Batterien nach Angaben des Herstellers.
Notebook Preface Caution on Using Modem 1. Never install telephone wiring during a lightning storm. 2. Never install telephone jacks in wet locations unless the jack is specifically designed for wet locations. 3. Never touch uninsulated telephone wires or terminals unless the telephone line has been disconnected at the network interface. 4. Use caution when installing or modifying telephone lines. 5. Avoid using the telephone function (other than a cordless type) during an electrical storm.
Notebook Preface Macrovision Notice This product incorporates copyright protection technology that is protected by U.S. patents and other intellectual property rights. Use of this copyright protection technology must be authorized by Macrovision, and is intended for home and other limited viewing uses only unless otherwise authorized by Macrovision. Reverse engineering or disassembly is prohibited. Safety Instructions 1. Read the safety instructions carefully and thoroughly. 2.
Notebook Preface Liquid has penetrated into the equipment. The equipment has been exposed to moisture. The equipment has not worked well or you can not get it work according to User’s Manual. The equipment was dropped and damaged. The equipment has obvious signs of breakage. 11. Never pour any liquid into the opening that could damage the equipment or cause an electrical shock. 12.
Notebook Preface kommunale Abfälle entsorgt werden, die sich auf 13.August, 2005 wirken. Und der Hersteller von bedeckt Elektronik-Altgeräte gesetzlich zur gebrachten Produkte am Ende seines Baruchbarkeitsdauer zurückzunehmen.
Notebook Preface Vervuiling van Electrische en Electronische producten (2002/96/EC), die op 13 Augustus 2005 in zal gaan kunnen niet meer beschouwd worden als vervuiling. Fabrikanten van dit soort producten worden verplicht om producten retour te nemen aan het eind van hun levenscyclus.. (Srpski) Po Direktivi Evropske unije ("EU") o odbačenoj ekektronskoj i električnoj opremi, Direktiva 2002/96/EC, koja stupa na snagu od 13.
Notebook Preface povinni odebírat takové výrobky zpět po skončení jejich životnosti. (MAGYAR) Az Európai Unió („EU") 2005. augusztus 13-án hatályba lépő, az elektromos és elektronikus berendezések hulladékairól szóló 2002/96/EK irányelve szerint az elektromos és elektronikus berendezések többé nem kezelhetőek lakossági hulladékként, és az ilyen elektronikus berendezések gyártói kötelessé válnak az ilyen termékek visszavételére azok hasznos élettartama végén.
Notebook Preface Trademarks All trademarks are the properties of their respective owners. Microsoft is a registered trademark of Microsoft Corporation. Windows®98/ME, 2000/XP are registered trademarks of Microsoft Corporation. AMI® is a registered trademark of American Megatrends Inc. PCMCIA and CardBus are registered trademarks of the Personal Notebook Memory Card International Association. Release History Version Revision Note Date 1.
Notebook Preface Table of Content Preface Regulations Information ...................................................................................II Safety Guideline for Using Lithium Battery ...................................................III Caution on Using Modem ............................................................................... IV Optical Device Drive Notice............................................................................ IV Macrovision Notice ............................
Notebook Preface Right-side View ......................................................................................2-10 Left-side View.........................................................................................2-12 Rear View...............................................................................................2-13 Bottom View ...........................................................................................2-14 Power Management.............................................
Notebook Preface BIOS Setup About BIOS Setup ..........................................................................................4-2 When to Use BIOS Setup.........................................................................4-2 How to Run BIOS Setup ..........................................................................4-2 Control Keys.............................................................................................4-3 BIOS Setup Menu ...............................................
Notebook Preface Restoring the System by Using the System Recovery Software Restoring the System by Using the System Recovery Software .............7-2 Mandatory Activation Mandatory Activation ................................................................................8-2 Safety EMC and Safety Regulations Safety EMC and Safety Regulations........................................................9-2 Laser (Safety Warning) ............................................................................
Notebook General Introductions Congratulations on becoming a new user of this notebook, the finely designed notebook. This brand-new exquisite notebook will give you a delightful and professional experience in using notebook. We are proud to tell our users that this notebook is thoroughly tested and certified by our reputation for unsurpassed dependability and customer satisfaction. How to Use This Manual This User’s Manual provides instructions and illustrations on how to operate this notebook.
Notebook General Introductions Chapter 3, Customizing this Notebook, gives instructions not only in connecting the mouse, keyboard, webcam, printer, external monitor, IEEE 1394 devices, and communication devices, but also in installing and removing the PC card. Chapter 4, BIOS setup, provides information on BIOS Setup program and allows you to configure the system for optimum use.
Notebook General Introductions Unpacking First, unpack the shipping carton and check all items carefully. If any item contained is damaged or missing, please contact your local dealer immediately. Also, keep the box and packing materials in case you need to ship the unit in the future.
Notebook Getting Started Specification Physical Characteristic Dimension 395mm(L) x 278mm(D) x 35mm(H) Weight 3.
Notebook Optical Device Getting Started COMBO/DVD dual/DVD Dual layer I/O Port Monitor(DVI) DVI USB x 4 (USB version 2.0) Mic-in x1 Internal Microphone x1 Webcam x1 Headphone/SPDIF Out x1 RJ11 x1 RJ45 x1 IEEE 1394 x1 TV-Out x 1 (S-Video) 5-in-1 Card Reader XD/SD/MMC/MS/MS Pro Express Card x1 Communication Port 56K Fax/MODEM AZALIA Modem MDC (AZALIA) Controller --- AZALIA Embedded LAN 10/100/1000 Base on board LAN Wireless LAN IEEE 802.
Notebook Getting Started Video Controller NVIDIA Geforce Go 7600 VRAM GDDR III (256MB) LCD 1440 x 900 for WXGA CRT Support 640x480, max, 32bit color 800x600, max, 32bit color 1024x768, max, 32bit color 1152 x 768, max 32bit color 1280 x 1024, max. 32bit color 1400x1050, max, 32bit color 1600 x 1200, max.32bit color 1800 x 1440, max.
Notebook Getting Started Product Overview This section provides you the description of basic aspects of your Notebook. It will help you to know more about the appearance of this Notebook before using it. Top-open View Press the Cover Latch to open the top cover (LCD Panel). The figure of top-open view and description showing below will lead you to browse the main operating area of your NOTEBOOK.
Notebook 1. Getting Started Cover Latch (Internal View) It is a bounce-back device to lock the cover with the deck when closing your Notebook PC. 2. Rubber Pads Protect your Notebook PC from random closing. 3. Stereo Speakers Make high quality sound blaster with stereo system and Hi-Fi function supported. 4. Quick Launch Buttons and Power Button Power Button: To turn your Notebook power ON and OFF.
Notebook 7. Getting Started Webcam This camera takes pictures every few minutes and updates those pictures to a Web page where everyone can watch. 8. Internal Microphone There is built-in microphone and its function is the same with microphone. 9. Status LED Hard Disk In-use: Glowing when the Notebook PC is accessing the hard disk drive. Num Lock: Glowing when the Num Lock function is activated. Caps Lock: Glowing when the Caps Lock function is activated.
Notebook Getting Started Front View 1. Cover Latch (External View) Press Cover Latch rightward and lift the cover. The Cover Latch will bounce back when loosing it. 2. IEEE 1394 The IEEE 1394 port is a high-speed bus that allows you to connect high-end digital devices such as the DV (digital video camera). 3. Audio Port Connectors Make high quality sound blaster with stereo system and Hi-Fi function supported. Headphones: A connector for speakers or headphones. 5.
Notebook Getting Started external microphone. 5.1: Central/Subwoofer 4. Status LED Battery: Glowing Green when recharging. Battery LED goes out when recharging is done or when the AC adapter is disconnected. Glowing Orange when the battery is in low battery status. Blinking Orange if the battery is out of order, and it is recommended to replace a new battery. Power On/ Off/ Suspend: Blinking when the system is in suspend mode; LED goes off when the system is activated. 1. Wireless LAN/ 2. Bluetooth: 1.
Notebook Getting Started Right-side View 1. Express Card Slot The computer provides an Express Card slot. The new Express Card interface is smaller and faster than PC Card interface. The Express Card technology takes advantage of the scalable, high-bandwidth serial PCI Express and USB 2.0 interfaces. 2. PC Card Slot The computer provides a PC card slot to support one Type-II PC card for expansion functions, such as LAN/WLAN card, modem card, memory card, etc. 3. USB Port The USB 2.
Notebook 5. Getting Started Ventilator The ventilator is designed to cool the system. DO NOT block the ventilator for air circulation. 6. DVI Port DVI stands for Digital Visual Interface, and is a standard for connecting computers to digital monitors. The DVI port provides a pure digital video signal to a digital flat-panel display or projector for a great view of the computer display.
Notebook Getting Started Left-side View 1. USB Port The USB 2.0 port allows you to connect USB-interface peripheral devices, such as the mouse, keyboard, modem, portable hard disk module, printer and more. 2. Optical Storage Device A slim CD-ROM/DVD-ROM/CD-RW/DVD Combo/DVD Dual drive is available in the computer, depending on the model you purchased. The optical device allows you to use the CD/DVD disc for installing software, accessing data and playing music/movie on the computer. 3.
Notebook Getting Started Rear View 1. Kensington Lock This port is used to lock the computer to location for security. 2. Power Connector To connect the AC adapter and supply power for the computer. 3. RJ-11 Connector The computer provides a built-in modem that allows you to connect an FJ-11 telephone line through this connector. With the 56K V.90 modem, you can make a dial-up connection. 4. RJ-45 Connector This connector is used to connect a LAN cable for network connection. 5.
Notebook Getting Started Bottom View 1. Battery Release Button It is a bounce-back device as a preparation for releasing the battery pack. Press it with one hand and pull the battery pack carefully with the other. 2. Battery Lock/Unlock Button Battery cannot be moved when the button is positioned on lock status. Once the button is pushed to unlock position, the battery is removable. 3. Battery Pack Supply power to your computer when the AC adapter is not connected.
Notebook Getting Started Power Management AC Adapter Please be noted that it is strongly recommended to connect the AC adapter and use the AC power while using this Notebook for the first time. When the AC adapter is connected, the battery is being charged immediately. NOTE that the AC adapter included in the package is approved for your Notebook; using other adapter model may damage the Notebook or other devices on the Notebook. Connecting the AC Power 1.
Notebook Getting Started Disconnecting the AC Power When you disconnect the AC adapter, you should: 1. Unplug the power cord from the electrical outlet first. 2. Unplug the connector from the Notebook. 3. Disconnect the power cord and the connector of AC adapter. 4. When unplugging the power cord, always hold the connector part of the cord.
Notebook Getting Started Battery Pack This Notebook is equipped with a high-capacity 6-cell/9-cell Li-ion Battery pack. The rechargeable Li-ion battery pack is an internal power source of the Notebook. Releasing the Battery Pack It’s a better way to have extra battery for enough power supply, so you don’t have to worry about the lack of battery power. It’s recommend to buy a battery pack from your local dealer. To remove the battery pack: 1. Make sure the computer is turned off. 2.
Notebook Getting Started 2-18
Notebook Getting Started Replacing the Battery Pack 1. Insert the right side of battery pack into the compartment. 2. Slightly slide and press the battery pack into the right place. 3. After the right side of the battery pack fitting the right track, then slightly press the left side of battery pack into the battery chamber. 4. Make sure the Lock/Unlock Button is in lock position. Warning 1. Do not try to disassemble THE BATTERY PACK. 2.
Notebook Getting Started Using the Battery Pack Battery Safety Tips Replacing or handling the battery incorrectly may present a risk of fire or explosion, which could cause serious injury. Only replace the main battery pack with the same or equivalent type of battery. Do not disassemble, short-circuit or incinerate batteries or store them to temperatures above +60° C (+140° F). Do not temper with batteries. Keep them away from children. Do not use rusty or damaged batteries.
Notebook Getting Started Charging the Battery Pack Properly Your notebook computer features a powerful, rechargeable Li-Ion battery pack. Normally, a fully charged battery delivers approx. 2 to 3 hours of battery operation for your notebook. It is very important that you enable the Power Management features under Windows XP for careful management of power consumption. The endurance will vary depending on the different notebook configurations as well as work habits.
Notebook Getting Started your notebook turned on until it automatically toggles to the Standby mode. Then reconnect the power adapter in order to recharge the battery. 4. As a rule the battery capacity will reduce to approx. 85% after performing 500 charging cycles. 5. Never leave the battery unused for a long period of time. All batteries are subject to self-discharge. Storing the battery for a long time may cause a low discharge status that could damage the battery.
Notebook Getting Started Basic Operations If you are a beginner to the Notebook, please read the following tips to make yourself safe and comfortable during the operations. Safety and Comfort Tips The Notebook is a portable platform that allows you to work anywhere. However, choosing a good workspace is important if you have to work with your Notebook for long periods of time. Your work area should have enough illumination.
Notebook Adjust the angle and position of LCD panel. Getting Started Keep your hands and feet with optimal comfort. Sit straight and keep a good posture. Adjust the desk’s height. Adjust the chair’s height. Have a Good Work Habit Have a good work habit is important if you have to work with your Notebook for long periods of time; otherwise, it may cause discomfort or injury to you. Please keep the following tips in mind when operating. Change your posture frequently.
Notebook Getting Started Knowing the Keyboard The Notebook’s keyboard provides all the functions of a full-sized 103-key keyboard and an additional [Fn] key for specific functions on the Notebook. The keyboard can be divided into four categories: Typewriter keys, Cursor keys, Numeric keys and Function keys.
Notebook Getting Started Typewriter Keys Typewriter Keys The function of these Typewriter keys is the major function of the keyboard, which is similar to the keys on a typewriter. It also provides several keys for special purposes, such as the [Ctrl], [Alt] and [Esc] key. When the lock keys are pressed, the corresponding LEDs will light up to indicate their status: Num Lock: Press and hold the [Fn] key and press this key to toggle the Num Lock on and off.
Notebook Getting Started Cursor Keys The keyboard provides four cursor (arrow) keys and [Home], [PgUp], [PgDn], [End] keys at the lower right corner, Cursor Keys which are used to control the cursor movement. Move the cursor left for one space. Move the cursor right for one space. Move the cursor up for one line. Move the cursor down for one line. Move to the previous page. Move to the next page. Move to the beginning of the line (or document). Move to the end of the line (or document).
Notebook Getting Started The Backspace key, [Ins] and [Del] keys at upper right corner are use for editing purpose. This key is used to switch the typing mode between “insert” and “overtype” modes. Press this key to delete one character to the right of the cursor and move the following text left for one space. Press this key to delete one character to the left of the cursor and move the following text left for one space.
Notebook Getting Started Function Keys Windows Keys You can find the Windows Logo key ( ( ) and one Application Logo key ) on the keyboard, which are used to perform Windows-specific functions, such as opening the Start menu and launching the shortcut menu. For more information of the two keys, please refer to your Windows manual or online help. [Fn] Key Switch the display output mode between the + + + + + + + LCD, external monitor and Both. Disable/enable Touchpad.
Notebook Getting Started Knowing the Touchpad The touchpad integrated in your Notebook is a pointing device that is compatible with standard mouse, allowing you to control the Notebook by pointing the location of the cursor on the screen and making selection with its two buttons. 1. Cursor Movement Area This pressure-sensitive area of the touchpad, allows you to place your finger on it and control the cursor on the screen by moving your finger. 2. Right Button Acts as the mouse’s right button. 3.
Notebook Getting Started Using the Touchpad Read the following description to learn how to use the touchpad: Positioning and Moving Place your finger on the touchpad (usually using the forefinger), and the rectangular pad will act as a miniature duplicate of your display. When you move your fingertip across the pad, the cursor on the screen will move simultaneously in the same direction. When your finger reaches the edge of the pad, lift your finger and replace it on a proper location of the touchpad.
Notebook Getting Started desired location; finally, release the left button to finish the drag-and-drop operation. Using the Touchpad Move the cursor by sliding your fingertip. Put your wrist on the desk comfortably.
Notebook Getting Started Configuring the Touchpad You can customize the pointing device to meet your personal needs. For example, if you are a left-hand user, you may want to swap the functions of the two buttons. In addition, you can change the size, shape, moving speed and other advanced features of the cursor on the screen. To configure the touchpad, you can use the standard Microsoft or IBM PS/2 driver in your Windows operating system.
Notebook Getting Started About Hard Disk Drive Your Notebook is equipped with a 2.5-inch IDE (Integrated Drive Electronics) hard disk drive. The hard disk drive is a storage device with much higher speed and larger capacity than other storage devices, such as the floppy disk drive and optical storage devices. Therefore, it is usually used to install the operating system and software applications. 1. To avoid unexpected data loss in your system, please backup your critical files regularly. 2.
Notebook Getting Started Using the Optical Storage Your Notebook is equipped with an optical storage device, which is known as the CD/DVD-ROM, CD-RW, DVD Combo and DVD Dual drive. The actual device installed in your Notebook depends on the model you purchased. CD-ROM Drive: Allows you to read CD disks, including audio CDs and CD-R/RW disks. DVD-ROM Drive: Allows you to read DVD disks and CD disks, including movie DVDs, audio CDs and CD-R/RW disks.
Notebook 1. Getting Started The optical storage devices are classified as a Class 1 Laser products. Use of controls or adjustments or performance of procedures other than those specified here in may result in hazardous radiation exposure. 2. Do not touch the lens inside the drive.
Notebook Getting Started Inserting the CD The following instruction describes the general procedure when operating the optical storage device, including the DVD-ROM drive. 1. Confirm that the Notebook is turned on. 2. Press the Eject Button on the drive’s panel and the CD tray will slide out partially. Then, gently pull the tray out until fully extended. 3. Place your CD in the tray with its label facing up. Slightly press the center of the CD to secure it into place. 4.
Notebook Getting Started Removing the CD 1. Press the Eject Button on the drive’s panel and the CD tray will slide out partially. Then, gently pull the tray out until fully extended. 2. Hold the CD by its edge with your fingers and lift it up from the tray. 3. Push the tray back into the drive. 1. Confirm that the CD is placed correctly and securely in the tray before closing the tray. 2. Do not leave the CD tray open.
Notebook Customizing this Notebook Connecting the External Devices The I/O (input/output) ports on the Notebook allow you to connect peripheral devices.
Notebook Customizing this Notebook Connecting the Peripheral Devices Connecting the Mouse You can connect a mouse to your Notebook through the USB port. To connect the mouse: 1. Turn on the Notebook and install the mouse driver. 2. Connect your mouse to the Notebook. 3. The Notebook may auto detect your mouse driver and enable the mouse function. If there is no detection of you mouse you can manually enable the mouse by going to Start Menu Æ Control Panel Æ Add Hardware to add the new device.
Notebook Customizing this Notebook Connecting the Printer If your printer has a USB interface, you can then use the USB port on the Notebook to connect the printer. The following instruction describes the general procedure to connect a printer: 1. Turn off the Notebook. 2. Connect one end of the printer cable to the Notebook’s USB port and the other end to the printer. 3. Connect the power cord and turn on the printer. 4. Turn on the Notebook and the system will detect a new device.
Notebook Customizing this Notebook Connecting the IEEE 1394 devices The IEEE 1394 port of your Notebook is a next-generation serial bus that features a high-speed transfer rate and the connection of up to 63 devices, allowing you to connect many high-end peripheral devices and consumer electronic appliances, such as the DV (digital video camera). The IEEE 1394 standard interface supports “plug-and-play” technology, so that you can connect and remove the IEEE 1394 devices without turning off the Notebook.
Notebook Customizing this Notebook Connecting the Communication Devices Using the LAN The RJ-45 connector of the Notebook allows you to connect the LAN (local area network) devices, such as a hub, switch and gateway, to build a network connection. This built-in 10/100 Base-T LAN module supports data transfer rate up to 100Mbps. For more instructions or detailed steps on connecting to the LAN, please ask your MIS staff or network manager for help.
Notebook Customizing this Notebook PC Card Installation The PC card slot of your Notebook allows you to install comprehensive Type-II PC cards that support various functions for your necessary, including the LAN/WLAN card, modem card and memory card. The following instruction provides you with a basic installation for the PC card, including how to install and remove it. For more information, please refer to the manual of your PC card. Installing the PC card 1.
Notebook Customizing this Notebook Removing the PC card 1. Press the Eject Button to make it stretch out. 2. Push the Eject Button and the PC card will slide out. Pull it out of the slot. Eject Button 1. Do not hold the “golden finger” when installing the PC card; otherwise, it may cause interference or damage to the PC card. 2. Before removing the PC card, you should stop the device in Windows operating system.
Notebook Customizing this Notebook Safely Remove Hardware If you connect any peripheral device to your system, the Safely Remove Hardware icon ( ) will appear on the taskbar. Double-click the icon to bring up the Safely Remove Hardware dialog box. You can see all connected peripheral devices here. If you want to remove any of the devices, move the cursor to the device and click Stop.
Notebook Customizing this Notebook 3-10
Notebook BIOS Setup About BIOS Setup When to Use BIOS Setup? You may need to run the BIOS Setup when: An error message appears on the screen during the system booting up and requests you to run SETUP. You want to change the default settings for customized features. You want to reload the default BIOS settings. How to Run BIOS Setup? To run the BIOS Setup Utility, turn on the Notebook and press the [Del] key during the POST procedure.
Notebook BIOS Setup Control Keys You can use only the keyboard to control the cursor in the BIOS Setup Utility. Press left arrow to select one menu title. Press right arrow to select one menu title. Press up arrow to select one item under the menu title. Press down arrow to select one item under the menu title. + Increase the setting value or make changes. Decrease the setting value or make changes. 1) Open the selected item to change setting options. 2) Bring up a sub-menu when available.
Notebook BIOS Setup BIOS Setup Menu Once you enter the BIOS Setup Utility, the Main menu will appear on the screen. The Main menu displays the system information, including the basic configuration. Main menu Show System Overview information about BIOS version, CPU features, Memory size and setting of System Time and Date. Advanced menu Configure IDE and USB settings. Security menu Install or clear Supervisor’s and User’s Password settings. Boot menu Set up Boot Type and Boot Sequence.
Notebook BIOS Setup Main menu System Overview System Overview will show you BIOS version and other information about its build date and update notes. Following is CPU’s information about its Type and Speed. System Time This item allows you to set the system time. The system clock will go on no matter you shut down the PC or get into sleep mode. The set format is [hour:minute:second].
Notebook BIOS Setup System Date This item allows you to set the system date. The date format is [day:month:date:year]. Day Day of the week, from Sun to Sat, which is determined by BIOS (read-only). Month The month from 01 (January) to 12 (December). Date The date from 01 to 31. Year The year can be adjusted by users. Primary IDE The item displays the types of the primary IDE devices installed in the Notebook.
Notebook BIOS Setup Advanced menu Advanced Settings PowerNow This item allows you to enable or disable PowerNow technology. When set to Enabled, the system always operates in a conserve power mode. If you want optimize the processor, set this item to Disabled, so that the processor’s speed will vary depending on the use of your operating system and applications. Default setting is set to Enabled. PCI Latency Timer Value in units of PCI clocks for PCI device latency timer register.
Notebook BIOS Setup Boot menu Boot Settings Configuration Configure settings during system boot. Boot Device Priority --1st, 2nd, and 3rd Boot Device The three items allow you to set the sequence of boot devices where BIOS attempts to load the disk operating system.
Notebook BIOS Setup Security menu Security Settings Change Supervisor/User Password When you select the function, a message box will appear on the screen as below: Enter New Password Type the password you want, up to six characters in length and press [Enter]. The password typed now will replace any previously set password from CMOS memory. You may also press [ESC] to abort the selection and not enter a password.
Notebook BIOS Setup When the Supervisor Password is set, the new item User Access Level and Password Check will be added in the menu. You can make further settings of access right in the User Access Level item. Setting options: No Access, View Only, Limited and Full Access. The Password Check item is used to specify the type of BIOS password protection that is implemented. Setup Settings are described below: The password prompt appears only when end users try to run Setup.
Notebook BIOS Setup Exit menu Exit & Save Changes Save the changes you have made and exit the utility. Exit & Discard Changes Exit the utility without saving the changes you have made. Discard Changes Abandon your changes and reload the previous configuration before running the utility. Load Setup Defaults Select this item to load the default settings for optimal system performance.
Notebook BIOS Setup 4-12
Notebook Troubleshooting, First Aid and FAQ Troubleshooting, First Aid and FAQ This notebook computer is a carefully tested, high-quality computer system offering the latest technology. However, problems and malfunction can never be totally avoided. In order to help you restore a fully-functional system we have collected together some detailed information about identifying and resolving the most common problems. If you have any problem, proceed as follows: - Read the "Troubleshooting" section.
Notebook Troubleshooting, First Aid and FAQ Troubleshooting If your notebook hangs while running or booting this can be due to a recently installed software. This can be solved as follows: - Power your notebook on. First of all you'll see the usual BIOS messages. As soon as they have finished, press the [F8] key. This will display the Windows XP boot menu. Select the Safe Mode command. Windows will now boot in a special "emergency mode".
Notebook Troubleshooting, First Aid and FAQ If you do not hear any sound, there are several possible reasons for hardware or software malfunction. In order to locate them better, proceed as follows: - Make sure that the sound card driver has been installed and that you have selected the sound card as default audio device.
Notebook Troubleshooting, First Aid and FAQ is working properly. - Try a different modem cable. - Make sure that the modem cable has been properly inserted into the modem port. - Try a different telephone wall socket (easy when using a notebook). - Try connecting to a different ISP to get Internet access. - Establish a test connection to a normal telephone number (e.g. your mobile phone) by clicking Programs/Accessories/Communications/HyperTerminal.
Notebook Troubleshooting, First Aid and FAQ FAQ – Frequently Asked Questions Where Can I Find Spare Parts and Accessories? Targa offers a wide range of spare parts and accessories for your PC. +49 2921 / 99-3030 only English Information About Drivers, FAQs and Manual In order to have all components of your Targa computer optimally tuned, you should regularly install the latest drivers. You can download them free from the Targa Service site on the Internet.
Notebook Troubleshooting, First Aid and FAQ Why does My Computer Show a Smaller Hard Disk Size than the Advertised Size, e.g. 111GB Instead of the Advertised 120GB? Solution: The reason is the different units used for calculating this value. All manufacturer documents use units referring to base 10 digits. Therefore, 120 GB correspond to 120 billion bytes (this is a 120 followed by 9 zeros). However, the computer calculates using units based on 1024.
Notebook Troubleshooting, First Aid and FAQ How Can I Enable/Disable the Autorun of CD-ROMs in Windows XP? Solution: Click Start/Run and enter "regedit". Search for the HKEY_LOCAL_MACHINE\System\CurrentControlSet \Services\Cdrom key and then the entry Autorun. Double-click on the entry to edit the value: 1 = enabled 0 = disabled. After changing this value you must restart your computer. The e-mail hotkey always launches Microsoft Outlook, but I want to use a different mail program.
Notebook Troubleshooting, First Aid and FAQ Are you receiving undesired messages (spam) via Windows Messaging Service? This is a new form of “Internet spam”. The Windows Messaging Service normally used for sending messages in a local network is misused to spread undesired or sometimes dangerous publicity mail to Internet users. In order to block these messages under Windows XP proceed as follows: Click the Start button in the lower-left corner.
Notebook Troubleshooting, First Aid and FAQ Pixel errors on LCDs (notebook computers + monitors) Active Matrix LCDs (TFT) with a resolution of 1440 x 900 pixels (XGA) rendered by three sub-pixels each (red, green, blue), a total of almost 3,9 million control transistors are used. Due to this high amount of transistors and the corresponding complex manufacturing process, in some cases faulty or the wrong driving of pixels and/or sub-pixels can occur.
Notebook Troubleshooting, First Aid and FAQ Types of pixel errors Type 1: pixel always lights (bright, white dot) Type 2: pixel never lights (dark, black dot) Type 3: abnormal or defective sub-pixel of the colors red, green or blue (lighting continuously, not lighting or blinking) Classes of pixel errors I 0 0 0 II 3 3 7 III 5 15 50 IV 50 150 500 The number of errors for the above mentioned types in each error class refers to one million pixels and must be converted according to the phys
Notebook Troubleshooting, First Aid and FAQ 1,296,000 pixels in total. Referring this figure to 1 million pixels, a factor of approx. 1.29 is obtained. Therefore, error class II permits two errors of type 1 or type 2 and five errors of type 3. Error class 1 only applies for special applications (e.g. medical) and implies higher costs. Error class II has become a standard for quality-orientated manufacturers with very good displays.
Notebook Watching TV and Videotext on your Notebook Watching TV and Videotext on your Notebook The Windows Media Center also features a complete TV receiver with which you can watch live TV programmes with total convenience. Operation is truly simple as the Media Center is very similar to a traditional TV. Most functions can be used intuitively so that you can master the operation with a few simple steps.
Notebook C Watching TV and Videotext on your Notebook To watch the current TV programme simply select Live-TV. The Media Center will enable the TV receiver and display the channel that was last watched. In the bottom left of the control panel you can control the TV programmes. By using the + and – keys in the channel function (ch + / -) you can scroll through all programmes. If you find an interesting channel, you need do nothing more.
Notebook Watching TV and Videotext on your Notebook channel. E The more channels you receive, the more difficult it is to search for channels of interest. This is especially so if you have more than a hundred channels via satellite: they can easily be lost track of. This is where the function Suchen can help. By using this you have a clear and convenient search mask. You can search for channels according to categories, titles or keywords.
Notebook Watching TV and Videotext on your Notebook Using Teletext (Videotext) on a Computer (Only for Analog TV) With the Windows Media Center you can naturally not only watch the current TV programmes, but also see Teletext/Videotext or their respective channels. The same information is available to you as you would find on a traditional TV. You can access this additional information with a few clicks of the mouse. A Firstly, use the function Live-TV to go the current TV programme.
Notebook Watching TV and Videotext on your Notebook Receiving Radio Channels with the Media Center The Windows Media Center also has a full-function FM radio receiver. With this you can receive traditional radio channels and listen directly to the computer. In this case, it offers you the comfort of a normal radio receiver. Prior to being able to receive radio broadcasts with your computer, you must guarantee a good signal reception. The easiest way to do this is by using a cable box.
Notebook C Watching TV and Videotext on your Notebook As soon as a channel with good reception has been found, the scanning stops. By using the plus and minus keys in the function Abstimmung (+ / -) you can carry out a fine tuning of the frequency. D If you would like to hear a channel regularly, you can save it. There are nine memory preset available. As soon as the desired channel is configured, click the button Speichern next to the frequency display.
Notebook Watching TV and Videotext on your Notebook The Media Center as a Video Recorder Once you have configured the Media Center and all the TV programmes are set up, you can watch current TV programmes comfortably and in high quality. The programme package can do more though. It also features a complete digital video recorder. This means you can record the TV programme you are viewing and save it as a file on your hard disk. The saved TV shows can be opened later anytime and watched as you wish.
Notebook Watching TV and Videotext on your Notebook the quality with which the film should be saved. Options available are: Ausreichend, Gut, Besser and Optimal These are quality levels that work with different compression rates. The higher the desired recording quality, the more data will be saved to your hard disk. For everyday recording the setting Gut is perfectly suitable. The setting Besser clearly compresses the picture less, but at the same time uses more hard disk space.
Notebook D Watching TV and Videotext on your Notebook Back in the main window you can start recording your TV programme. First choose the desired programme. When you are ready, simply click on the recording button – that's the red cricle below on the control panel. Additionally, the Media Center displays an icon in the Windows task bar that reminds you of the current recording. E Just as with a traditional video recorder you can now watch the currently-running programme whilst you are recording it.
Notebook Watching TV and Videotext on your Notebook By clicking Aufzeichn. hinzufügen you can program a new TV programme to be automatically recorded. G Use the Aufzeichn. hinzufügen button to go to the window for new recordings. There are several ways to program the desired programme. The electronic TV newspaper is listed using the TV-Programm function. With this you can conveniently click on the programme of your choice and the video recorder soon receives all the necessary data.
Notebook Watching TV and Videotext on your Notebook 6-12
Notebook Restoring the System by Using the System Recovery Software Restoring the System by Using the Restoring the System by Using the System Recovery Software The EasyInstall CD/DVD supplied with your Targa PC contains a completely new Recovery software that lets you restore your PC gradually into a normal operating status.
Notebook Restoring the System by Using the System Recovery Software 1. A message warning of a possible loss of data will appear. Click the button Run program.
Notebook Restoring the System by Using the System Recovery Software 2. In the next step you can choose between the four options mentioned above. 3. If you have trouble starting Windows, first try the option Restore Boot Files Only. 4. If you have problems with Windows system files that cannot be solved after executing the Windows System Restore, try the second option Restore System Files. 5.
Notebook Restoring the System by Using the System Recovery Software Important! Please remember that launching this process will restore the factory default configuration of your computer. This will erase any data from your hard disk (under Windows labeled drive C:). If you don't want this, exit the Recovery software and backup your personal data first (e.g. on a CD-ROM or on the second partition (Install) of your hard disk). 7. Launch the recovery process by clicking the Start button.
Notebook Restoring the System by Using the System Recovery Software 8. Click the OK button to confirm the warning message in the next window. 9. The system recovery process starts. This process may take a while. You can monitor the completion status of the recovery in the progress bar. Important! You must never turn off your computer while the recovery process is running.
Notebook Restoring the System by Using the System Recovery Software 10. After the recovery has finished click Restart Computer to restart your computer.
Notebook Restoring the System by Using the System Recovery Software 7-8
Notebook Mandatory Activation Restoring the System Mandatory Activation by Using the The license rights granted under this EULA are limited to the first thirty (30) days after you first install the SOFTWARE unless you supply information required to activate your licensed copy in the manner described during the setup sequence of the SOFTWARE. You can activate the SOFTWARE through the use of the Internet or telephone; toll charges may apply.
Notebook Safety EMC and Safety Regulations Safety EMC and Safety Regulations This device is compliant to the standards EN 55022, EN 55024, EN 61000-3-2, EN 61000-3-3 and EN 60950. The included RF appliances, e.g. WLAN, comply with the R&TTE Directive (1999/5/EG, ETSI EN 300 328, EN 301489-1, EN 301489-17). The supplied TV receiver conforms to the standards EN 55013 and EN 55020.
Notebook Safety EMC and Safety Regulations Laser (Safety Warning) This device contains a laser system and is rated as a "Class 1 Laser Product". Please refer to the Operating Instructions, and read them carefully for instructions on correct operation. Keep them as reference for future use. If you encounter problems with your notebook, please contact qualified service or maintenance personnel.
Notebook Safety EMC and Safety Regulations Additional Safety Instructions for Devices with Wireless LAN Your notebook features a Wireless LAN appliance. Therefore you must read and follow these safety instructions when working with your notebook: • Turn the notebook off when traveling in an airplane or in a car.
Notebook Safety EMC and Safety Regulations CE Marking for Devices with Wireless LAN This device complies with the Directive 1999/5/EG of the European Parliament and Council dated March 9, 1999 for radio and telecommunications equipment and has been proven to meet mutual immunity and conformity.
Notebook Safety EMC and Safety Regulations Restrictions France Restricted Frequency Band Only channels 10 to 11 (2,457 MHz and 2,462 MHz) may be used in France. Outdoor use of the device is not allowed. Info: www.art-telecom.fr Italy A ministerial license is also required for indoor use. Contact your reseller for the required procedure. Outdoor use of the device is not allowed. Info: www.agcom.it Netherlands A license is required for outdoor use. Contact your reseller for the required procedure.
Notebook Safety EMC and Safety Regulations channels that may be used in each country: Channel MHz Europe, R&TTE France, R&TTE 1 2412 X 2 2417 X 3 2422 X 4 2427 X 5 2432 X 6 2437 X 7 2442 X 8 2447 X 9 2452 X 10 2457 X X 11 2462 X X 9-7
Notebook Safety EMC and Safety Regulations Regulations – Exclusion of Liability Exclusion of Liability for Wireless LAN Devices Installing and operating wireless LAN devices must be in accordance with the instructions contained in the user documentation. This user documentation is contained in the product package. Any modifications to the device that have not explicitly been approved by the manufacturer may void the operating authorization of the device.
