TAOTRONICS WALL FAN NORMA L 8 SLEEP BREEZE HIGH MEDHIGH Questions or Concerns? support@taotroincs.
Contents IMPORTANT SAFETY INSTRUCTIONS 01 ASSEMBLING YOUR FAN 04 USING YOUR FAN 09 CLEANING AND MAINTENANCE 14 TROUBLESHOOTING 16 WARRANTY AND SERVICE 18
01 INTENDED USE BEFORE USING THIS APPLIANCE READ ALL INSTRUCTIONS AND CAUTIONARY MARKINGS IN YOUR USER MANUAL AND ON THE APPLIANCE. IMPORTANT SAFETY INSTRUCTIONS DO NOT touch or hold the mains plug with wet hands. • Close supervision is necessary when any appliance is used by or near children. Children should be supervised to ensure that they do not play with the appliance. Cleaning and user maintenance shall not be done by children unless they are older than 8 and supervised.
• WARNING: To Reduce The Risk Of Fire Or Electric Shock, Do Not Use This Fan With Any Solid-State Speed Control Device. • Include instructions pertaining to a risk of fire, electric shock, or injury to persons, for cleaning and user-maintenance, such as lubrication. • DO NOT operate any fan with a damaged cord or plug. Discard fan or return to an authorized service facility for examination and/or repair. FOR HOUSEHOLD USE ONLY READ AND SAVE THESE INSTRUCTIONS • DO NOT run cord under carpeting.
Assemble Your Fan 1. 2. 1 Position the rear grille onto the fan head and turn the grille nut clockwise to secure the rear grille. (Note: The three alignment holes must be aligned with the three prongs.) Remote Control 1 2 NORMA L 8 SLEEP BREEZE 4 1 2 NORM AL 8 HIGH SLEEP LOW MEDHIGH MEDLOW Front Grille Blade Cap Blade Rear Grille Nut Rear Grille Fan Head Screws Wall Bracket Screw Anchors Unscrew the rear grille nut counterclockwise.
Assemble Your Fan Mount Your Fan 3. 4. 2 X Length X＝Y 2 Y NORMA L 8 SLEEP BREEZE H IG H 4 1 2 LOW M EDHIGH MEDLOW MED NORM AL 8 1 SLEEP BREEZ E NORM AL 4 2 HIGH 8 SLEEP BREEZ E HIGH 4 LOW MEDHIGH 1 MEDLOW MED 2 LOW MEDHIGH MEDLOW M ED 1 Open up all locking clips. 1 07 Wall Fan 2 Align front and rear grilles, then snap the front grille into place as the illustration shows. 3 Put all clips back to clamp tightly.
Control Panel 03 Fan Speed Power ON/Standby Press to start / stop oscillating. NORMAL HIGH USING YOUR FAN SLEEP BREEZE LOW MEDHIGH MEDLOW 8 1 4 2 MED Fan Mode Press repeatedly to cycle through NORMAL, SLEEP, BREEZE. Summon A Cool Breeze Into Your Space 09 Wall Fan Oscillation Press repeatedly to cycle through LOW, MED-LOW, MED, MED-HIGH, HIGH. Turn on /Standby mode. Timer • Press to set timer for turning on / off the fan (1H-2H-4H-8H). • Long press to cancel timer.
Remote Control Fan Modes Additional Features Note: For added convenience, the same control buttons can be found on the remote control. Memory Function: The fan is designed with power off memory function. It will always remember your last settings (except timer setting) once you turn it on again. 2 1 4 3 Power ON/Standby Oscillation NORMAL 8 SLEEP BREEZE HIGH 4 1 2 LOW MEDHIGH MEDLOW MED Timer Fan Speed LED ON/OFF • NORMAL: LOW, MED-LOW, MED, MED-HIGH, HIGH.
Replacement of Battery • Replace with new batteries of the same type when replacement is required. • When not using the remote control for a long time, please take out the batteries. • Do not attempt to dismantle the batteries. • Do not dispose the batteries in fire, batteries may explode or leak. • Do not use rechargeable batteries. WARNING: Do not ingest battery, Chemical Burn Hazard. This product contains a coin / button cell battery.
Always take the fan off wall before cleaning for safety reasons. 05 A soft cloth is recommended for cleaning the blade. To remove dust between the grilles, a pipe cleaner, flexible dust wand, vacuum cleaner or compressed air are acceptable. TROUBLESHOOTING • Always make sure the wall fan is turned off and unplugged before cleaning. • DO NOT stick any foreign objects or your fingers inside of the unit. • Never immerse in water or allow water to drip into the motor housing.
Q A Excessive noise. Fan does not operate. Oscillation is not steady or fan vibrates. Why the remote control is not working. • It is normal that there is noise during operation. If too loud, please set the fan to lower speed. • Check if the blade is installed properly. • Make sure the fan is connected to a powered electrical outlet. • Make sure the fan is mounted firmly on a vertical wall. • Clean the blade regularly. • Make sure the fan is connected to a powered electrical outlet.
Rev_1.3_EN Model:TT-TF011 support@taotronics.com CM www.taotronics.com Manufacturer: Shenzhen NearbyExpress Technology Development Co.,Ltd.
