TaoTronics Barcode reader setup manual TT-BS001 / TT-BS002 Setup procedures are as follows： 1、 Scan “Begin setting” 2、 Scan your required function and its corresponding barcode 3、 Scan “End setting” 4、 All the setting parameters will be saved after scanning “Save setting parameter” 5、 All the settings will be returned to the manufacture default parameters after scanning “Setup the manufacture parameters” Attention： 1、 This manual is available for a special barcode reader which produced by our company 2、 Th
Setup main menu Begin setting End setting Cancel setting Save setting parameter Return to the manufacture setting Return to the saved setting parameter Interfaces setup *Keyboard wedge RS232 Emulational lightpen OCIA USB -2-
Memory function *ON OFF Read mode setup *Turn off light source after reading Trigger ON/OFF Continue scan/Trigger Disable Twinkle Continue scan/Auto-inductive Enable Twinkle/ Auto- inductive Enable Note： 1、 Trigger ON/OFF：Light source will shine when press switch， otherwise light source won’t shine, Keep pressing until read some information, then the light source will go out.
to twinkle in 6 seconds. 4、Continue scan/Auto-inductive Enable：The same information will be only read once unless move to other information, then move the scanner to the barcode again and read.
Data bit 7 *8 Stop bit *1 2 Parity bit *None Even Odd Mark Space Handshake protocol Note：Exchange pre-setup control signals or charactes’ programme when two installations or systems build connections.
RTS/CTS Enable *RTS/CTS Disable ACK/NAK Enable *ACK/NAK Disable XON/OFF Enable *XON/OFF Disable Keyboard wedge parameters setup Terminal types *IBM PC/AT,PS/2 IBM PC/XT IBM PS/2 25,30 NEC 9800 Apple Desktop Bus(ADB) IBM 5550 -6-
IBM 122 Key (1) IBM 102 Key IBM 122 Key (2) Capital/small letter *Non-change Capital Small letter ALT mode ON *OFF Explanation： ALT keystroke function：When this function is ON, the original -7-
setting character model of barcode will not be changed in spite of the keyboard lock is ON or OFF, that’s to say this function will not be affected by the keyboard lock, but it’s only available for PC. Figure keystrokes ON *OFF Explanation： Figure keystrokes：Output by figure keystrokes’ scanning barcode after this function is ON.
STX-ETX Explanation： STX-ETX： Only available for RS-232.
Explanation： Put off the time of intercharacter transmission Emulational lightpen parameters definition TTL signal statement *BAR denotes high electric frenquency BAR denotes low electric frenquency Scan rate *Fast Slow Output format *CODE 39 CODE 39 corpora Output original barcode format - 10 -
Explanation：Output by CODE39 Barcode parameters definition Choose identified barcode *UPC-A Enable Disable *UPC-E Enable Disable *EAN-13/JAN-13 Enable Disable *EAN-8/JAN-8 Enable Disable - 11 -
*CODE 39 Enable Disable *CODE 128 Enable Disable *CODEBAR/NW7 Enable Disable *Interleave 25 Enable Disable Industial 25 Enable * Disable Matrix 25 Enable * Disable CODE 93 Enable * Disable - 12 -
CODE 11 Enable * Disable China post Enable * Disable MSI/PLESSEY Enable * Disable BC412 Enable * Disable CODE 2 OF 6 Enable * Disable TELEPEN Enable * Disable All barcodes Enable - 13 -
UPC/EAN/JAN parameters definition Choose barcode types UPC-A=EAN 13 Enable *Disable ISBN Enable * Disable ISSN Enable * Disable With complementary bit decode Enable *Auto-identify complementary bit Complementary bit setup - 14 -
*No transmit Transmit 2 charaters Transmit 5 charaters Transmit 2 or 5 charaters UPC-A transmit parity bit Enable Disable UPC-E transmit parity bit Enable Disable EAN-8 transmit parity bit Enable Disable EAN-13 transmit parity bit Enable Disable ISSN transmit parity bit Enable Disable - 15 -
CODE 39 parameters definition Choose barcode types *Standard CODE39 Corpora *Italy Medicine Bureau barcode Disable Italy Medicine Bureau barcode Enable Transmit parity bit setup *No calculate parity bit Calculate parity bit Calculate parity bit、No transmit - 16 -
Output begin/end character setup（begin/end are‘*’ ） ON *OFF Decoding symbol“*” （CODE 39） ON *OFF Barcode length setup *Non-fixed length Fixed length（Be able to setup two groups） 1 、 Gruoup 1 Begin 3、Gruoup 1 2 、 Algorism number （ Appendix A ） End - 17 -
1、Gruoup 2 Begin 3、Gruoup 2 End Minimum length 1、Begin 2、 Algorism number（Appendix A） 2、 Algorism number（Appendix A） 3、End Explanation： 1、 ‘Non-fixed length’denotes that output characters are the same as barcode characters and no limiting 2、 ‘Fixed length’denotes that the setting barcode length is fixed, barcode characters are the same as the set value, otherwise output will be disable 3、 ‘Minimum length’setup characters’ minimum length.
disable if the set value is less than it.
Fixed length（Be able to setup two groups） 1、Group 1 Begin 2、 Algorism number（Appendix A） 3、Group 1 End 1、Group 2 Begin 3、Group 2 End Minimum length 1、Begin 2、 Algorism number（Appendix A） 2、 Algorism number（Appendix A） 3、End - 20 -
Explanation： 1、 ‘Non-fixed length’denotes that output characters are the same as barcode characters and no limiting 2、 ‘Fixed length’denotes that the setting barcode length is fixed, barcode characters are the same as the set value, otherwise output will be disable 3、 ‘Minimum length’sets characters’ minimum length. Output will be disable if the set value is less than it.
Barcode length setup *Non-fixed length Fixed length（Be able to setup two groups） 1、Group 1 Begin 2、 Algorism number（Appendix A） 3、Group 1 End 1、Group 2 Begin 3、Group 2 End Minimum length 1、Begin 2、Algorism number（Appendix A） 2、 Algorism number（Appendix A） - 22 -
3、End Explanation：1、 ‘Non-fixed length’denotes that output characters are the same as barcode characters and no limiting 2、 ‘Fixed length’denotes that the setting barcode length is fixed, barcode characters are the same as the set value, otherwise output will be disable 3、 ‘Minimum length’sets characters’ minimum length. Output will be disable if the set value is less than it.
Fixed length（Be able to setup two groups） 1、Group 1 Begin 2、 Algorism number（Appendix A） 3、Group 1 End 1、Group 2 Begin 3、Group 2 End Minimum length 1、Begin 2、 Algorism number（Appendix A） 2、 Algorism number（Appendix A） 3、End - 24 -
Explanation： 1、 ‘Non-fixed length’denotes that output characters are the same as barcode characters and no limiting 2、 ‘Fixed length’denotes that the setting barcode length is fixed, barcode characters are the same as the set value, otherwise output will be disable 3、 ‘Minimum length’sets characters’ minimum length. Output will be disable if the set value is less than it.
3、Group 1 End 1、Group 2 Begin 3、Group 2 End Minimum length 1、Begin 2、 Algorism number（Appendix A） 2、Algorism number（Appendix A） 3、End Explanation： 1、 ‘Non-fixed length’denotes that output characters are the same as barcode characters and no limiting 2、 ‘Fixed length’denotes that the setting barcode length is fixed, barcode - 26 -
characters are the same as the set value, otherwise output will be disable 3、 ‘Minimum length’sets characters’ minimum length.
D Begin D End Barcode length setup *Non-fixed length Fixed length（Be able to setup two groups） 1 、 Group 1 Begin 2 、 Algorism number （ Appendix A） 3、Group 1 End 1、Group 2 Begin 3、Group 2 End 2、 Algorism number（Appendix A） - 28 -
Minimum length 1、Begin 2、 Algorism number（Appendix A） 3、End Explanation： 1、 ‘Non-fixed length’denotes that output characters are the same as barcode characters and no limiting 2、 ‘Fixed length’denotes that the setting barcode length is fixed, barcode characters are the same as the set value, otherwise output will be disable 3、 ‘Minimum length’sets characters’ minimum length.
Fixed length（Be able to setup two groups） 1、Group 1 Begin 2、Algorism number（Appendix A） 3、Group 1 End 1、Group 2 Begin 3、Group 2 End Minimum length 1、Begin 2、 Algorism number（Appendix A） 2、 Algorism number（Appendix A） 3、End - 30 -
Explanation： 1、 ‘Non-fixed length’denotes that output characters are the same as barcode characters and no limiting 2、 ‘Fixed length’denotes that the setting barcode length is fixed, barcode characters are the same as the set value, otherwise output will be disable 3、 ‘Minimum length’sets characters’ minimum length. Output will be disable if the set value is less than it.
Barcode length setup *Non-fixed length Fixed length（Be able to setup two groups） 1 、 Group 1 Begin 2 、 Algorism number （ Appendix A） 3、Group 1 End 1、Group 2 Begin 3、Group 2 End Minimum length 1、Begin 2、 Algorism number（Appendix A） 2、 Algorism number（Appendix A） - 32 -
3、End Explanation： 1、 ‘Non-fixed length’denotes that output characters are the same as barcode characters and no limiting 2、 ‘Fixed length’denotes that the setting barcode length is fixed, barcode characters are the same as the set value, otherwise output will be disable 3、 ‘Minimum length’sets characters’ minimum length. Output will be disable if the set value is less than it.
*Non-fixed length Fixed length（Be able to setup two groups） 1 、 Group 1 Begin 2 、 Algorism number （ Appendix A） 3、Group 1 End 1、Group 2 Begin 2、 Algorism number（Appendix A） 3、Group 2 End Minimum length 1、Begin 2、 Algorism number（Appendix A） - 34 -
3、End Explanation： 1、 ‘Non-fixed length’denotes that output characters are the same as barcode characters and no limiting 2、 ‘Fixed length’denotes that the setting barcode length is fixed, barcode characters are the same as the set value, otherwise output will be disable 3、 ‘Minimum length’sets characters’ minimum length. Output will be disable if the set value is less than it.
Fixed length（Be able to setup two groups） 1、Group 1 Begin 2、Algorism number（Appendix A） 3、Group 1 End 1、Group 2 Begin 3、Group 2 End Minimum length 1、Begin 2、 Algorism number（Appendix A） 2、 Algorism number（Appendix A） 3、End - 36 -
Explanation： 1、 ‘Non-fixed length’denotes that output characters are the same as barcode characters and no limiting 2、 ‘Fixed length’denotes that the setting barcode length is fixed, barcode characters are the same as the set value, otherwise output will be disable 3、 ‘Minimum length’sets characters’ minimum length. Output will be disable if the set value is less than it.
Fixed length（Be able to setup two groups） 1 、 Group 1 Begin 2 、 Algorism number （ Appendix A） 3、Group 1 End 1、Group 2 Begin 3、Group 2 End Minimum length 1、Begin 2、Algorism number（Appendix A） 2、 Algorism number（Appendix A） 3、End Explanation： - 38 -
1、 ‘Non-fixed length’denotes that output characters are the same as barcode characters and no limiting 2、 ‘Fixed length’denotes that the setting barcode length is fixed, barcode characters are the same as the set value, otherwise output will be disable 3、 ‘Minimum length’sets characters’ minimum length. Output will be disable if the set value is less than it.
Fixed length（Be able to setup two groups） 1、Group 1 Begin 2、Algorism number（Appendix A） 3、Group 1 End 1、Group 2 Begin 3、Group 2 End Minimum length 1、Begin 2、 Algorism number（Appendix A） 2、 Algorism number（Appendix A） 3、End Explanation： - 40 -
1、 ‘Non-fixed length’denotes that output characters are the same as barcode characters and no limiting 2、 ‘Fixed length’denotes that the setting barcode length is fixed, barcode characters are the same as the set value, otherwise output will be disable 3、 ‘Minimum length’sets characters’ minimum length. Output will be disable if the set value is less than it.
Belgium tongue Portuguese Denish Dutch Turkish Barcode distinguishing symbol definition ON *OFF Default parameter Explanation： When this function is ON, there is a character which appends after decoding code and before code each time. You can judge the barcode type which are decoded according to the following representations.
UPC-A EAN-8 CODE 39 INTERLEAVE 25 MATRIX 25 CODE 93 China post barcode BC412 TELEPEN UPC-A A C E G I K M O T UPC-E EAN-13 CODE-128 INDUSTRIAL 25 CODABAR/NW7 CODE 11 MSI/PLESSEY CODE 2 OF 6 B D F H J L N P UPC-E EAN-13/JAN-13 EAN-8/JAN-8 CODE 39 CODE 128 CODABAR/NW7 INTERLEAVE 25 INDUSTRIAL 25 MATRIX 25 CODE 93 CODE 11 - 43 -
China post barcode MSI/PLESSEY BC412 CODE 2 OF 6 TELEPEN Precision definition *Once Twice 3 Times 4 Times Explanation：The delayed time between two data output 1. Reduce the rate of mis-decoding. 2. This option is repeating decoding times. The more decoding, the more accurate of output information，but the time of decoding will increase accordingly at the same time.
Beep volume definition *High Medium Low OFF Continue distinguish delicacy definition *Fast Slow Explanation： Fast／Slow is the decoder speed under continue mode.
Explanation： Barcode data will be output in inverted. For example：a barcode data is：12345, the output result is 54321 when the function is ON.. Delete output character definition Setup deleting character Setup a certain barcode（Be able to setup 6 groups data in total simultaneously） Delete some characters from start with a certain characters.
Group 3 Group 4 Group 5 Group 6 Choose barcode type definition UPC-A UPC-E EAN-13/JAN-13 EAN-8/JAN-8 CODE 39 CODE 128 CODABAR/NW7 INTERLEAVE 25 - 47 -
INDUSTRIAL 25 MATRIX25 CODE 93 CODE 11 China post barcode MSI/PLESSEY BC412 CODE 2 OF 6 TELEPEN All barcodes None Deleting character location 1、Algorism number 2、End - 48 -
(Appendix A) Delete character quantity 1、Algorism number 2、End (Appendix A) Insert character definition Setup inserting characters Setup a certain barcode（Be able to setup 6 groups data in total simultaneously） Insert several charaters from start with a certain character According to the following steps： 1、 Scan corresponding group barcode； 2、 Scan corresponding barcode type； 3、 Scan the barcode of representating “insert character location” in appendix A； 4、 Scan the “end” barcode of “insert character loc
Group 3 Group 4 Group 5 Group 6 Choose barcode type definition UPC-A UPC-E EAN-13/JAN-13 EAN-8/JAN-8 CODE 39 CODE 128 CODABAR/NW7 INTERLEAVE 25 - 50 -
INDUSTRIAL25 MATRIX25 CODE 93 CODE 11 China post barcode MSI/PLESSEY BC 412 CODE 2 OF 6 TELEPEN All barcodes None Insert character location - 51 -
1、Algorism number 2、End （Appendix A） Insert characters 1、ASCII table、Function keys table 2、End （Appendix B、Appendix C） Setup infrared ray inductor *OFF ON Appendix A 0 Algorism number Table 1 - 52 - 2
3 4 5 6 7 8 9 Appendix B ASCII Table Space SOH - 53 -
STX ETX ENQ EOT ACK BEL HT BS LF VT FF SO CR SI - 54 -
DC1 DLE DC2 DC3 DC4 SYN NAK ETB CAN SUB EM FS - 55 -
ESC GS RS US ！ Space “ ＃ ％ ＄ ＆ （ - 56 -
‘ ） + * ’ .
4 5 6 7 8 9 ； ： 〈 〉 ＝ ？ - 58 -
@ B A C E F D G H I J K - 59 -
L M N O P Q R S T U V W - 60 -
X Y Z [ ] \ ^ _ .
d e f g h i j k l m n o - 62 -
p q r s t u v w x y z { - 63 -
} | ~ DEL Appendix C Function keys Table F1 F2 - 64 -
F3 F4 F5 F6 F7 F8 F9 F10 F11 F12 Insert Delete Page Up Page Down - 65 -
Home End Left Right Down Up Appendix D General fault elimination of barcode reader 1.
and the receiving speed of host computer. Generally this case arises, it’s because the speed of the reader’s transmitting data can’t cooperate with the host. The solution is to change the character time-delay of the reader. 2.
and so there is different in skip line when using different software, this is normal case. You can change this situation just through modifying the settings of terminal equipment. 5. Q: Why is there no start-up sound after start up power supply? A: Check if connection wire is in good condition, if the connection wire is OK, please check if the reader’s interface is also OK. （Suggest the user to test in another connection wire, or test in different equipments and in the same connection wire）. 6.
afresh, and perform download function again. c. Please confirm using correct COM port and communication parameter when using RS232 interface; or check if connection wire is OK; or inquire about software edition and discuss with engineer d. Please confirm connecting keyboard or replace another keyboard; or test with different operating system; or inquire about software edition and discuss with engineer. Appendix E Some common ways to Keep the reader in good condition 1.
2) The protection flake is not suitable for using rough paper or cloth to wipe. 3) Clean protection flake occasion: Be not able to scan barcode rightly 4) The ways of cleaning protection flake： i) Common maintain ways：Get a piece of clean cotton cloth (or a piece of clean paper) with adding a little liquid (clean water. alcohol) to wipe the transparent flake, note: too much liquid will be easily inleak the inside reader and result in damaging the hardware of reader. ii) Deep maintain ways a.
1） Two terminals of wire（the reader port connection，the host port connection）are faintish, although the wire is strengthened structurally, users still need to notice: the connection terminals are often folded or pressed, this will result in breaking the inside wires, so the reader can’t work normally. 2） Two terminals of wire（the reader port connection，the host port connection）are the fixed parts of the wire，Please not pull it forcibly to result in breakage and damage of the wire.
