. XR-3100 Crossband Repeater Installation Guide Tantalus Utility Network®
LEGAL NOTICES Notice The information contained in this document is subject to change without notice. Warranty Tantalus makes no warranty of any kind with regard to this material, including, but not limited to the implied warranties of merchantability and fitness for a particular purpose. Tantalus shall not be liable for errors contained herein or incidental consequential damages in connection with the furnishing, performance, or use of this material. Copyright Statement © 2005 Tantalus Systems Corp.
COMMUNICATIONS REGULATION INFORMATION RF Exposure Professional installation of this device is required. The radio equipment described in this guide emits radio frequency energy. Although the power level is low, the concentrated energy from a directional antenna may pose a health hazard. The following minimum distances apply in both indoor and outdoor environments.
. Use of batteries that are not Tantalus-approved may adversely affect the safe use of the transceiver, and will void the approval. FCC Part 15 Notice, USA The transceiver described herein complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference. 2. This device must accept any interference received, including interference that may cause undesired operation.
. Description Product Description The XR-3100 is a cross band repeater that transports TUNet traffic between the 220 MHz WAN and the 900 MHz LAN. The XR-3100 provides additional flexibility when deploying a network: • In hard to reach situations such as at range boundaries, where the device can be mounted high up to extend reach.
General Information Tantalus provides two-way, real-time data communications networks to monitor and control electric utilities. Our long-range wireless networks unite a utility’s applications, making meter reading, load management, and distribution automation cost-effective and practical throughout urban and rural service areas.
. Installing Installing the XR-3100 Before the XR-3100 is ready for installation in the field, it must be programmed in the Meter Shop. Warning Energized meters, meter sockets and distribution lines present the risk of electrical shock. All work on this equipment should be performed by qualified metering specialists or industrial electricians. Personnel working with this equipment should follow all utility company established operation and safety procedures.
PROGRAMMING CONFIGURATION LED WAN STATUS LED Figure 1 The XR-3100 serial port with the DT100 Cross band programming cable attached. Figure 2 Position of the XR-3100 programming and status LEDs Figure 3 Switch position to select the LAN Controller. page 4 LAN STATUS LEDs (3) Figure 4 The green programming CONFIG LED indicating communication to the LAN Controller. 5. Plug in the power cord. The CONFIG LED should now be green as shown in Figure 4.
Meter Settings Tab Consumption reading digit count: default Initial Consumption reading: default Meter Identifier: Enter a unique identifier for the unit, ie “Utility pole 12345”, “1234 Broadway Street” Network Settings Utility business identifier: Enter in the assigned business ID number for your utility provided by Tantalus. Installing the Tantalus XR-3100 Version 1.
Application Settings Uncheck all the boxes 8. Click the program icon . Now close the DT-150 program. 9. Unplug the XR-3100. Switch the toggle on the programming cable to the WAN position. 10. Unplug the cord and disconnect it from the terminal block. 11. Return the XR-3100 to the original packaging. Ensure that you include at least one battery in the packaging with the device but do NOT install it in the XR-3100. page 6 Tantalus Systems Corp.
INSTALLATION INSTRUCTIONS FOR THE FIELD This product should not be installed during heavy rain or snow as there may pose a risk of electric shock. Warning 1. Remove the XR-3100 from the packaging. Ensure that you have a battery for the device, but do NOT install it until step 4. 1. Ensure that there is no power source connected to the XR-3100. 2. Ensure that both battery compartments are empty. Warning 2.
Mounting bracket: The mounting bracket can be fixed to a utility pole by metal strapping or by threaded rod. The bracket has also been designed to mount to horizontal poles and hand rails. It is recommended to first mount the bracket first then mount the XR-3100 to the bracket using the 4 thread cutting screws that come with the bracket. ! All 4 screws must be securely installed for protection against the environment. Failure to do so will void warranty. Caution page 8 Tantalus Systems Corp.
3. If you are using the supplied internal antenna, go to Step 4. – or – If you are installing the Tantalus-approved external antenna: a. Remove the internal antenna by unscrewing the TNC plug from the TNC jack. b. Remove the ½” trade knockout on the bottom left of the device. It is recommended to use a utility knife, flat head screw driver and hammer to facilitate removal. c. Run the coaxial cable from the outside of the box and up through the knockout. Connect the cable to the TNC jack. d.
4. Install the battery in the XR-3100. Depress the battery cover tab, lift the cover, and install the batteries (orientation not critical) with the exposed contacts inward. ! Ensure that you are using a Tantalus-approved battery only. Do NOT apply power to the XR-3100 until the battery has been installed. Caution 5. Attach power to the XR-3100: a. Connect the white power/neutral wire, black power wire, and green chassis ground wire to the terminal block per the markings on the inner cover. b.
. Troubleshooting Troubleshooting the XR-3100 Warning Energized meters, meter sockets and distribution lines present the risk of electrical shock. All work on this equipment should be performed by qualified metering specialists or industrial electricians. Personnel working with this equipment should follow all utility company established operation and safety procedures.
LAN NETWORK STATUS LED (RED) Start-up/Power up Solid RED Module is not programmed Fast flashing RED Unassociated/Re-associating Solid RED Valid association candidate found Flashing RED Full network association confirmed OFF LAN APPLICATION MESSAGE TRANSACTION LED (GREEN) Start-up/Power-up OFF Message queued for transmission Long flash GRN Valid message received (addressed to this device) Short flash GRN LAN RF PACKET LED (AMBER) Start-up/Power-up OFF RF packet transmitted Long flash Amber
. Contact Contact Information TANTALUS SYSTEMS CORP. 100-2955 Virtual Way Vancouver, BC Canada V5M 4X6 Tel: 604-299-0458 Fax: 604-451-4111 Email: info@tantalus.com Installing the Tantalus XR-3100 Version 1.
