User manual
R i s k o f F i r e
Keep combustible materials such as furniture, papers, clothes and curtains at least 1.8m (6 feet) from the front of the heater and
away from the sides and rear. If the lamp is to be used outside, we recommend that a waterproof or indoor socket is used.
I n t r o d u c t i o n
The Rio IP heater produces radiant heat like the sun, warming people and objects rather than the air in between. It is mounted on an adjustable bracket
that allows the heat to be directed exactly where it is required. Its attractive, lightweight design means that it is effective yet unobtrusive. The Rio IP is
designed for indoor and outdoor use so is therefore weatherproof.
Please read the following instructions carefully before use. The safety of this heater is guaranteed only by its correct usage in accordance
with these instructions, therefore it is recommended that they are retained for future reference.
S p e c i f i c a t i o n
T a b l e 1 . U K , E u r o p e a n a n d A u s t r a l i a / N e w Z e a l a n d H e a t e r s
Use MCB Type 3
C a u t i o n
Before using this appliance:
- Check that the voltage indicated on the type plate corresponds to the mains supply voltage.
- Ensure that the heater has been securely fastened in its final mounting position.
Do not locate the heater immediately below a socket outlet.
Remove the plug from the mains socket (or disconnect pole switch) during installation, cleaning and/or replacing the emitter
and always ensure that the emitter is cool.
Do not handle the halogen emitter with bare hands. If it is inadvertently touched, remove finger marks with a soft cloth and
methylated spirit or rubbing alcohol. Otherwise, the marks will burn into the quartz glass causing premature heater failure.
Do not use an extension cable with this product.
Keep the mains cable away from the body of the heater which will get hot during use.
Do not cover or obstruct the heater while it is in use.
This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or
lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a
person responsible for their safety. Children should be supervised to ensure that they do not play with the appliance.
Do not insert any object through any slot or opening in the heater.
Do not use if guard is not present.
Do not install less than the minimum mounting distance from the floor.
Do not touch the heater when it is turned on, as the body gets hot.
Do not use the heater in a bathroom.
Warning - this appliance must be earthed!
Model Voltage Total Current Min height Min distance Min distance Dimensions Weight Ingress
(V) Power (A) from floor from ceiling from side wall W x H x D (kg) Protection
(W)
(m) (m) (m) (mm)
(IP)
Rio 210IP 230 1000 4.3 2.0 0.3 1.5 390 x 100 x 155 2.35 IP24
Rio 215IP 230 1500 6.5 2.0 0.3 1.5 390 x 100 x 155 2.35 IP24
Rio 220IP 230 2000 8.7 2.0 0.3 1.5 390 x 100 x 155 2.35 IP24
2
F o l l o w i n g i n f o r m a t i o n i s o n l y f o r E U - m e m b e r s t a t e s :
The use of this symbol indicates that this product may not be treated as household waste. By ensuring this product is
disposed of correctly, you will help prevent potential negative consequences for the environment and human health,
which could otherwise be caused by inappropriate waste handling of this product. For more detailed information about
recycling of this product, please contact your local council, your household waste disposal service or the shop where you
purchased the product.
H a n d l i n g t h e R e p l a c e m e n t E m i t t e r
Your new emitter should not be handled with bare hands. Remove finger marks with a soft cloth and methylated spirits or rubbing
alcohol. Finger marks will burn into the emitters quartz glass causing premature failure.
Y o u r R e p l a c e m e n t E m i t t e r
It is very important that your replacement emitter is exactly the same as the one it was supplied with. Failure to fit the exact same type could cause the
heater to fail or even become dangerous especially when used in an outdoor environment.
Please contact Tansun Limited to purchase your replacement emitter and state the model number of the heater you wish to fit the emitter to.
7