Specification Sheet

VQNET 85DF
VQNET 85DF // issue 1.01 // 22.11.11
Tannoy adopts a policy of continuous improvement and product specication is subject to change
Tannoy United Kingdom T: 00 44 (0) 1236 420199 E: [e-mail]
Tannoy Deutschland T: 00 49 (180) 1111 881 E: [e-mail]
TC|Group International T: 00 45 8742 7000 E: [e-mail]
TC|Group Americas T: 00 1 [phone] E: [e-mail]
PSU Specications
Input Connector Locking Neutrik Powercon
Voltage Selection Automatic (115 / 230V, 45 - 65Hz)
Type High current, high frequency switch mode
Efciency >90% typical
Input voltage 100V / 115V / 230V nominal +/-10%
Mains fuse External
Fuse type T10AT
Other features Automatic soft start
Current Draw 115V 230V
Startup (inrush) 3.5A 1.9A
idle 1.0A 0.56A
Max 3.5A 1.7Ae
Construction
Enclosure 18mm (0.71”) birch plywood.
Internally braced.
Grille Powder coated perforated
steel grille
Finish Textured black or white paint
(custom colours on request)
Connectors 1 x female XLR (input)
1 x male XLR (link)
1 x RJ45 (network in)
1x RJ45 (network link)
1 x Neutrik Powercon
1 x Neutrik Powercon (outlet)
Controls & Indicators LED on front of cabinet behind grill.
(wink indicator for locating & assigning)
Power LED (Blue)
Signal LED (Green)
Limit LED (Red)
User DSP - defeat switch
Power Switch
Fittings 2 x Recessed carrying handles
11 x M10 ying inserts
Dimensions 500 mm x 694mm x 515mm
(19.69” x 27.32” x 20. ”)
Net Weight 30.5kg (67.1 lbs)
Notes:
(1) Average over stated bandwidth. Measured at 3 metres on axis, then referred to 1 metre
(2) Unweighted pink noise input, measured at 3 metres in an anechoic chamber, then
referred to 1 metre
A full range of measurements, performance data, CLF and Ease™ Data can be
downloaded from www.tannoy.com
Full independent verication of published specications carried out by NWAA Labs,
California can also be obtained from the downloads section of www.tannoy.com
Tannoy operates a policy of continuous research and development. The introduction
of new materials or manufacturing methods will always equal or exceed the
published specications, which Tannoy reserves the right to alter without prior
notice. Please verify the latest specications when dealing with critical applications.
TECHNICAL SPECIFICATIONS
System VQNET 85MH
System Type 2-Way Mid/High - Point Source
Frequency Response (-3dB)
(1)
400Hz - 23kHz
Frequency Range (-10dB)
(1)
350Hz - 27kHz
Dispersion (-6dB) 80 x 50 degrees
Driver Complement MF/HF Dual Concentric™
Compression driver loaded into
a single PSW™ Waveguide
Crossover 7kHz (DSP generated)
Recommended HighPass
Filter @ 450Hz (DSP generated)
Directivity Factor (Q) 13.3 averaged 1kHz to 10kHz
Directivity Index (DI) 11.2 averaged 1kHz to 10kHz
Rated Maximum SPL
(2)
134dB (average) 140dB (peak)
Distortion
110dBSPL 2nd Harmonic 3rd Harmonic
500Hz 2.165 0.733
2kHz 1.507 0.123
5kHz 1.308 0.161
115dBSPL
500Hz 3.487 0.997
2kHz 2.553 0.212
5kHz 2.252 0.326
120dBSPL
500Hz 5.895 1.558
2kHz 4.400 0.374
5kHz 3.882 0.789
125dBSPL
500Hz 11.482 5.364
2kHz 7.516 0.897
5kHz 6.871 2.972
Electronics
Efciency >85% typically
Damping Factor 120 ref 8 Ohms
Distortion <0.05% @ 1kHz -3dB output
(22kHz bandwidth)
Input Impedance 5.6 kOhms unbalanced,
11.2 kOhms balanced
Output Power (Programme) 400W MF, 200W HF (limited to)
Input Sensitivity 1.4V (+5.5dBu)
System Type Dual channel Class D
DSP System
Comms Facilities Firmware updatable and selected
parameters editable
Communications Serial - RS485 Proprietary
message format
Dynamic Range 112dB(A) typical
DSP 3rd generation SHARC
Sampling Frequency 96kHz 24 bit A/D-D/A word length
Format 1 IN - 2 OUT
Ordering Information
PART NUMBER MODEL NAME COLOUR PACKED QUANTY
8001 4860 VQNET 85DF BLACK 1
8001 4861 VQNET 85DF WHITE 1
28