Specification Sheet

VQNET 64MH
VQNET 64MH // issue 1.00 // 14.07.10
Tannoy adopts a policy of continuous improvement and product specication is subject to change
Tannoy United Kingdom T: 00 44 (0) 1236 420199 E: [e-mail]
Tannoy Deutschland T: 00 49 (180) 1111 881 E: [e-mail]
Tannoy Middle East T: 00 971 (04) 4401208 E: [e-mail]
TC|Group International T: 00 45 8742 7000 E: [e-mail]
TC|Group Americas T: 00 1 [phone] E: [e-mail]

 
 2-Way Mid/High - Point Source


 400Hz - 23kHz


350Hz - 27kHz
 60 x 40 degrees
MF/HF Dual Concentric™
Compression driver loaded into
a single PSW™ Waveguide
 7kHz (DSP generated)
Recommended HighPass
Filter @ 450Hz (DSP generated)
 21.3 averaged 1kHz to 10kHz
 13.3 averaged 1kHz to 10kHz


 -

 2nd Harmonic 3rd Harmonic
500Hz 1.674 0.271
2kHz 0.812 0.035
5kHz 0.955 0.049

500Hz 3.015 0.396
2kHz 1.430 0.056
5kHz 1.544 0.184

500Hz 5.637 0.865
2kHz 2.505 0.144
5kHz 2.184 0.342

500Hz 11.135 3.278
2kHz 4.302 0.394
5kHz 1.160 0.598

 >85% typically
 120 ref 8 Ohms
 <0.05% @ 1kHz -3dB output
(22kHz bandwidth)
 5.6 kOhms unbalanced,
11.2 kOhms balanced
 400W MF, 200W HF (limited to)
 1.4V (+5.5dBu)
 Dual channel Class D

 Firmware updatable and selected
parameters editable
 Serial - RS485 Proprietary
message format
 112dB(A) typical
 3rd generation SHARC
 96kHz 24 bit A/D-D/A word length
 1 IN - 2 OUT

    
      
       

 Locking Neutrik Powercon
 Automatic (115 / 230V, 45 - 65Hz)
 High current, high frequency switch mode
 >90% typical
 100V / 115V / 230V nominal +/-10%
 External
 T10AT
 Automatic soft start
 115V 230V
 3.5A 1.9A
 1.0A 0.56A
 3.5A 1.7Ae

 18mm (0.71”) birch plywood.
Internally braced.
 Powder coated perforated
steel grille
 Textured black or white paint
(custom colours on request)
 1 x female XLR (input)
1 x male XLR (link)
1 x RJ45 (network in)
1x RJ45 (network link)
1 x Neutrik Powercon
1 x Neutrik Powercon (outlet)
 LED on front of cabinet behind grill.
(wink indicator for locating & assigning)
Power LED (Blue)
Signal LED (Green)
Limit LED (Red)
User DSP - defeat switch
Power Switch
 2 x Recessed carrying handles
12 x M10 ying inserts
 510mm x 694mm x 515mm
(20.08” x 27.32” x 20.28”)
 48.5kg (106.7 lbs)
Notes:
(1) Average over stated bandwidth. Measured at 3 metres on axis, then referred to 1 metre
(2) Unweighted pink noise input, measured at 3 metres in an anechoic chamber, then
referred to 1 metre
A full range of measurements, performance data, CLF and Ease™ Data can be
downloaded from www.tannoy.com
Full independent verication of published specications carried out by NWAA Labs,
California can also be obtained from the downloads section of www.tannoy.com
Tannoy operates a policy of continuous research and development. The introduction
of new materials or manufacturing methods will always equal or exceed the
published specications, which Tannoy reserves the right to alter without prior
notice. Please verify the latest specications when dealing with critical applications.