VQ - Brochure

VQ NET 100 data file // issue 1.05 // 30.07.09
VQ NET 100
Tannoy adopts a policy of continuous improvement and product specification is subject to change
Tannoy United Kingdom T: 00 44 (0) 1236 420199 E: [e-mail]
Tannoy Deutschland T: 00 49 (180) 1111 881 E: [e-mail]
Tannoy France T: 00 33 (0) 1 7036 7473 E: [e-mail]
TC|Group Americas T: 00 1 [phone] E: [e-mail]
TECHNICAL SPECIFICATIONS
System Type 3-Way Full Range - Point Source
Frequency Response (-3dB)
(1)
115Hz - 23kHz
Frequency Range (-10dB)
(1)
90Hz - 27kHz
Dispersion (-6dB) 100 degrees conical
Driver Complement
LF 2 x 300mm (12.00”) Low
Frequency Transducers,
Semi Horn Loaded
MF/HF Dual Concentric™ Compression
driver loaded into a single
PSW™ Waveguide
Crossover 450Hz (DSP Generated)
7kHz (passive)
Directivity Factor (Q) 8.5 averaged 1kHz to 10kHz
Directivity Index (DI) 9.3 averaged 1kHz to 10kHz
Rated Maximum SPL
(2)
Average Peak
Low Frequency 134dB 140dB
Passive MF/HF 134dB 140dB
Construction
Enclosure
18mm (0.71") birch plywood.
Vented and internally braced.
Grille Powder coated perforated
steel grille
Finish Black or white textured paint
(custom colours on request)
Connectors 1 x female XLR (input)
1 x male XLR (link)
1 x RJ45 (network in)
1x RJ45 (network link)
1 x Neutrik Powercon
Controls & Indicators LED on front of cabinet behind
grille. (wink indicator for locating
& assigning)
Power LED (blue)
Signal LED (green)
Limit LED (red)
User DSP - defeat switch
Power switch
Fittings 8 x Recessed carrying handles
12 x M10 flying inserts
Dimensions 925mm x 694mm x 515mm
(36.42" x 27.32" x 20.28")
NET Weight 68kg
System
PART NUMBER MODEL NAME COLOUR PACKED QUANTITY
8001 4850 VQ NET 100 BLACK 1
8001 4851 VQ NET 100 WHITE 1
Ordering Information
Electronics
Efficiency >85% typically
Damping Factor 120 ref 8 Ohms
Distortion <0.05% @ 1kHz -3dB output
(22kHz bandwidth)
Input Impedance 5.6 kOhms unbalanced,
11.2 kOhms balanced
Output Power (Programme) LF - 800W
MF/HF - 800W (limited to 400W)
Input Sensitivity 1.4V (+5.5dBu)
System Type Dual channel Class D
DSP system
Comms Facilities Firmware updatable and selected
parameters editable
Communications Serial - RS485 Proprietary message format
Dynamic Range 112dB(A) typical
DSP 3rd generation SHARC
Sampling Frequency 96kHz 24 bit A/D-D/A word length
Format 1 IN - 2 OUT
PSU Specifications
Input Connector Locking Neutrik Powercon
Voltage Selection Automatic (115 / 230V, 45 - 65Hz)
Type High current, high frequency switch mode
Efficiency >90% typical
Input voltage 100V / 115V / 230V nominal +/-10%
Mains fuse External
Fuse type T10AT
Other features Automatic soft start
Current Draw 115V 230V
Startup (inrush) 3.5A 1.9A
idle
1.1A 0.56A
Max 3.5A 1.7A
Notes:
(1) Average over stated bandwidth. Measured at 3 metres on axis, then referred to 1 metre
(2) Unweighted pink noise input, measured at 3 metres in an anechoic chamber,
then referred to 1 metre
A full range of measurements, performance data, CLF and Ease™ Data can be
downloaded from www.tannoy.com
Tannoy operates a policy of continuous research and development. The introduction
of new materials or manufacturing methods will always equal or exceed the
published specifications, which Tannoy reserves the right to alter without prior
notice. Please verify the latest specifications when dealing with critical applications.
VQ Bookletv0909aw:Layout 1 4/9/09 11:23 Page 29