Specification Sheet

QFlex 24
Technical Data Sheet
Performance
Driver conguration 8 x 4” LF, 8 x 3” LF, 8 x 1” HF
Amplier channels 24 x 100 W rms @ 4 ohms
Amplier type Class D
Horizontal dispersion 120 degrees horizontal
Vertical dispersion Variable 10 – 100 degrees
Symmetrical or asymmetrical
Single or multiple beams
LF beam control limit 400 Hz
Frequency range (-10 dB) 110 Hz – 20 kHz
Maximum SPL
(1)
96 dB @ 30 m (100 ft)
Application distance
(2)
40 m (131 ft) typical
Sampling rate 96 kHz
Network VNET monitoring and control standard (optional Dante)
Connectors
Analogue audio 2 inputs (A & B), Phoenix 6-pin connectors
VNET Dual RJ45 connectors In/Link (for Cat-5 cable)
AES/EBU RJ45 (same Cat-5 as VNET) via AES/VNET interface
Power GST18 3-pole female power connector
Construction
Enclosure material Extruded aluminum
Power supply Universal 100 – 230 V / 50 – 60 Hz
Dimensions (HxWxD) 1483 x 171.5 x 150 mm, (29.3 x 6.7 x 5.9”)
Weight 26.3 kg (58 lbs)
Finish Standard: White
Special order: Any RAL colour
Accessories (optional unless stated): Mounting bracket (included)
USB VNET Interface (Part no: 8001 4150)
Constant Voltage Interface / 100 V Interface (Part no: 8001 6226)
SM-1 Sentinel Monitor (Part no: 8001 6300)M-1 Sentinel Monitor
AES Break-in box (Part no: 8001 6010)
VNET AES/Dante Bridge (Part no: 7600 2131)
Weather Protected specication (IP54)
Power supply specications
Ordering Information
Part Number Colour
8004 0121 White
Notes:
1. Average SPL (1 kHz – 8 kHz). Based on a
mounting height of 10 m (33 ft) and a target
area @ 30 m (98.5 ft) and 10 m (33 ft) wide.
Maximum attainable SPL is dependent on
the dimension of the target area(s). Exact
gures can be derived in the BeamEngine
programme.
2. Based on the above venue criteria achieving
95 dB SPL at the quoted distance.
3. Power save mode (amp switching inactivated).
4. No audio signal (other than pilot tone).
5. Stimulus - STIPA noise (speech-like
characteristics), Level - Signal over-riding
internal limiters.
A full range of measurements, performance data,
can be downloaded from www.tannoypro.com. For
project-specic system design assistance, contact
the AET group via www.aetgroup.tc
Tannoy operates a policy of continuous research and
development. The introduction of new materials or
manufacturing methods will always equal or exceed
the published specications. All specications are
subject to change without notice.
VNET and BeamEngine are trademarks of Tannoy
Limited. All other trademarks remain the property of
their respective owners.
Copyright (c) 2015 Tannoy Limited. All rights reserved.
Complies with UL60065.
This product can be environmentally
protected to IP54 rated standard as an
optional extra, specied upon ordering.
It is not suitable for fully-exposed
(uncovered) outdoor applications.
Output Power consumption Current draw (A)
(W) 230 Vac 115 Vac
STIPA Noise
(5)
125 1.0 1.6
1/3rd Full power 300 2.21 3.5
1/8th Full power 200 1.48 2.3
Idling
(4)
66 0.74 1
Quiescent
(3)
48 0.6 0.8
In Rush - 9.8 4.9
tannoypro.com
V 1.20 - 02.12.2015