User's Manual
Menu Settings Window Details
Check Data
The 83rd data reading is
highlighted by the cursor.
Data List
All recorded data is displayed in descending order (from the newest to the oldest
data). Specify data by moving cursors and press the <ENT> button to view detailed
information.
Judgment Result
Check Data
Data details (Date/Time of Recorded Data, Measurement Item, User Name,
Temperature, and Judgment Result) can be viewed.
ȤJudgment OKȁȁ ȤLower Limit Error
ȁȁ
ȤUpper Limit Error
Select User
elect and set the User Name of the persons who will measure temperature.
(Up to 63 user names can be registered into an RTR-61 unit.)
Select Item
Select and set the Measurement Items.
(Up to 63 items can be registered into an RTR-61 unit.)
Set Operation
ŋŶťŨŮŦůŵġōņŅ
Őŏ
ŐŇŇ
Judgment LED
It is possible to turn ON / OFF the blinking of Upper and Lower Limit Judgment
LED.
Button Sound
It is possible to turn ON / OFF the beep which sounds when pressing a button.
Backlight
The Backlight factory default setting for the RTR-61 is "ON in Use", which will
backlight the window for 3 seconds only when in operation. Here you can shift the
setting to "Always ON" or "Always OFF".
Unit of Temp.
Select Fahrenheit [ɋF] or Celsius [Ɏ ].
ńŭŰŤŬġŔŦŵŵŪůŨ
10
25
2007
09
32
ŜńŢůŤŦŭŞ ŜġŐŌġŞ
Clock Setting
The RTR-61 clock settings can be made here.
(See the following section "How to Make Clock Settings" for details.)
Contrast
It is possible to adjust the contrast of the display.
Remote Info
Before carrying out wireless communication, it is necessary for the Management
Operator to register Data Loggers (RTR-61 units) as Remote Units and register
them into Groups. The Group Name and Remote Unit Name can be viewed here
for the RTR-61 unit being used.
Memory Usage
132 of data readings
are recorded.
Each RTR-61 can record and store up to 1,800 of data readings. The number of
stored data can be viewed here.
ӳȁMain Window Names and Functions
See the following for the items displayed in the Top Window and the Main Menu Window.
ɡ Top Window
By turning the Power ON, the Top Window will appear.
Following are the main display items and marks that
appear in the Top Window.
Item
Unit
Recording Mode
Current
Temperature
Battery Status
or Wireless
Communication in
Progress
User NameCurrent Date / Time
Remote Mode
Current Temperature : The currently measured temperature will be
displayed.
Item : Up to 12 characters can be entered.
User Name : Up to 8 characters can be entered.
Current Date /Time : Current Time (Month / Date / Hour / Minute)
Unit [
] :
Select from Fahrenheit / Celsius
Recording Mode [
] :
Select from Endless / One Time
Battery Status [
] :
The remaining amount of battery power will
appear.
Wireless Communication in Progress
[ ] :
While wireless communication is occurring,
this mark will appear.
Remote Mode[
] :
The recording of temperature measurements
is being controlled by wireless
communication.
ɡ Main Menu Window
While the Top Window is being displayed, pressing the <MENU>
button on the face of the unit will display the Main Menu.
Cursor
Scroll
Title
Highlight
Title: The title of the menu will be displayed
Highlight: The cursor selected item is displayed in white letters on
a black background.
Cursor: Select the item by moving the Cursor up and down by
pressing the arrow buttons <
> on the face of the
unit.
Press the <ENT> button on the face of the unit to select
the desired menu.
Press the <MENU> button on the face of the unit to
return to the previous window.
Scroll : The scroll up and down arrows show that data exists
outside of the display area.
ɣȤ Press <
> button on the face of the unit to scroll
up.
ɥȤ Press <
> button on the face of the unit to scroll
down.
ɡ Recorded Temp
(Displayed normally after PUSH Recording)
PUSH Record LED "ON"
The recorded temperature is displayed for
about three seconds; after which the unit
returns automatically to the Top Window.
- If the Button Sound has been set to "ON", the unit beeps when recording
temperature.
ӷȁ
About the Message Display
Even when the power is OFF, an automatic Power-ON may occur to display a message.
Ӹȁ
Measurement Error Messages
If a temperature measurement error occurs, there may be a poor sensor connection. In such a case, an
Error Message will appear.
Ӷȁ
How to Make Clock Settings
In order to make the clock settings for the RTR-61 unit, please follow the directions as written below.
Ӵȁ
About the PUSH Recording Window
This window will appear by pressing the <REC> button on the RTR-61 unit to record temperature.
ɡ Wait for Temp
(Measuring in progress and waiting for the constant temp)
If the "Wait for Constant Temp Function" has been applied to your RTR-61 unit by the
Management Operator, this message will be displayed while waiting for the temperature
measurement to stabilize.
Do not remove the sensor while "Wait for
Temp" is on display and the PUSH
Record LED is blinking.
- When the "Wait for Constant Temp Function" is active, the temperature will not
be recorded until temperature stabilization has been achieved. Due to this,
after pressing the <REC> button it may take some time before the temperature
is actually recorded.
- If the temperature is not stabilized even after 15 seconds have elapsed,
recording will not be performed and you will be returned to the Top Window.
- If the Button Sound has been set to "ON", the unit beeps both when the "Wait
for Temp" operation has been started and when the temperature has been
recorded.
ӵȁ
Menu Contents
Details about the Main Menu and the Operational Settings Menu are as follows.
Depending on the settings, some operations are restricted from being carried out by manipulating
the buttons on the unit. Refer to the following for details:
ɡ Remote (Remote Mode)
When an RTR-61 unit has been set to "Remote Mode" by the
Management Operator, it is not possible to use the "PUSH
Recording" function without fi rst receiving a "Measurement
Command" from the Operator. Even while the power
is OFF, when an RTR-61 unit receives a "Measurement
Command", the LCD backlight will begin to fl ash and a
beeping sound will notify the user that it is time to carry out
a recording.
To record a measured temperature while in Remote Mode,
please carry out the following procedures:
1.
Open the [Clock Setting] window.
2.
By pressing the <ENT> button,
"Month" will blink.
By pressing the arrow buttons
<
>
, the numerical values get
larger or smaller.
3.
Press the <ENT> button to
determine the value. Then press
the arrow buttons <
> to move
the cursor.
4.
By pressing the <ENT> button,
"Day" will blink. By pressing the
arrow buttons
<
>
, the
numerical values get larger or
smaller.
5.
Press the <ENT> button to determine the value. After this,
please make all settings in the same way.
Pressing<
>Ȥ
Moves the cursor in the order of Month-Day-Year-Hour-
Minute.
Pressing<
>Ȥ
Moves the cursor in the order of Minute-Hour-Year-Day-
Month.
6.
Finally, move the cursor to the
position of "OK" and press the
<ENT> button to complete the
settings.
- To stop making clock settings at anytime, move the cursor to "Cancel" and
press the <ENT> button.
ɡ Settings Change Messages
If any settings changes have been
made via wireless communication
to the RTR-61 unit in use, a
notifi cation message will be
displayed for about two seconds.
After that, you will be automatically
returned to the Top Window.
- Messages will be displayed regardless of any mode settings in the RTR-61.
ɡ Created Messages
The RTR-61 unit can receive any
created message from the
Management Operator. They will
continue to be displayed until the
<ENT> button on the face of the
unit is pressed.
- By making the backlight light up or the beeping sound occur, the user can be
informed that a message has been received.
- Messages can be received regardless of mode settings in the RTR-61.
- Note that there is no message storing function, so messages will not be
redisplayed once you press the <ENT> button.
Check the sensor connection.
ɡ FULL when in One-time Mode
1.
Measurement Command
Message example
When a Measurement Command is
received, push the <ENT> button on the
face of the unit to return to the Top Window.
*The backlight fl ashing and beeping sound will continue
until the <ENT> button is pressed.
2.
Top Window
When the display switches to the Top
Window, the specifi ed item will be on
display.
3.
Please measure and record the
temperature of the specifi ed item.
This symbol shows that the data
recording capacity is full and no
more new data can be recorded. In
order to carry out recording again,
it is necessary to fi rst download the
recorded data from the RTR-61 to
the manager's computer and then
delete it from the unit.
ɡ Key Lock Function
Because the Management Operator
has placed a restriction on carrying
out direct operations using the
RTR-61, only the <REC> and <ON/
OFF> buttons are operable.
-
Note that if a Message (see Section ӷ ) or a Measurement Command is received from
the Management Operator, the <ENT> button will become operable.
Ӳȁ
Operations Table
This is a table of operations for RTR-61. When using, please refer to the following chart.
ńũŦŤŬġŅŢŵŢġġŜııĹĴŞ
’06 11/27 15:40
NG
ŊŵŦŮȇ
ŕŰŮġġġġġġġ
100 .9
Ɏ
ńŶŵŭŦŵ
ńũŦŤŬġŅŢŵŢ
ŔŦŭŦŤŵġŖŴŦų
ŔŦŭŦŤŵġŊŵŦŮ
ŎŢŪůġŎŦůŶ
Ɂ
ɦ
V
Ɂ
Y
őųŦŴŴġŵũŦ
ġġġġġġġţŶŵŵŰůŴġ
ŵŰġŴŦŭŦŤŵġŢġŖŴŦųįġġ
őųŦŴŴġŵũŦ
ġġġġġġġţŶŵŵŰůŴġ
ŵŰġŔűŦŤŪŧźġŅŢŵŢġġġ
őųŦŴŴġŵũŦ
ġġġġġġġţŶŵŵŰůŴġ
ŵŰġŴŦŭŦŤŵġŢůġŊŵŦŮį
ŔŦŵġŵũŦġŮŰůŵũĭġ
ťŢźĭġźŦŢųĭġũŰŶųġ
ŢůťġŮŪůŶŵŦį
ȺńŢůŤŦŭȻ
Őŏ
ŐŇŇ
]
őųŦŴŴġŵũŦġġġġġġġţŶŵŵŰůŴġŵŰġŴŦŭŦŤŵġŢġŎŦůŶįġ
őųŦŴŴġŵũŦġġġġġġġţŶŵŵŰůŴġŵŰġŴŦŭŦŤŵġŢġŎŦůŶįġ
œŦŮŰŵŦġŊůŧŰ
ňœŐŖő
ŖŏŊŕ
ȇġŏŢŮŦ
ȇġŏŢŮŦ
ŎŦŮŰųźġŖŴŢŨŦġ
őŖŔʼnġœŦŤŰųť
[0000/1800]
ŔŦŭŦŤŵŦťġŊŵŦŮ
ŊŵŦŮȇńŶŵŭŦŵ
ŖűűŦųġȇȁIJĹı
ōŰŸŦųȇȁIJijı
Ɏ
Ɏ
ŕŰŮ
ŪŴġŸŰųŬŪůŨġůŰŸ
őųŦŴŴġŵũŦ
ţŶŵŵŰůŴġ
ŵŰġŴŦŭŦŤŵĻ
Őŏ
ŐŇŇ
]
őųŦŴŴġŵũŦ
ţŶŵŵŰůŴġ
ŵŰġŴŦŭŦŤŵĻ
Ɏ
ȌŇ
]
őųŦŴŴġŵũŦ
ţŶŵŵŰůŴġ
ŵŰġŴŦŭŦŤŵĻ
őųŦŴŴġŵũŦ
ţŶŵŵŰůŴġŵŰġŢťūŶŴŵġ
ŵũŦġŤŰůŵųŢŴŵġŭŦŷŦŭ
łŭŸŢźŴġŐŏ
łŭŸŢźŴġŐŇŇġ
ŐŏġŪůġŶŴŦġ
]
őųŦŴŴġŵũŦ
ţŶŵŵŰůŴġ
ŵŰġŴŦŭŦŤŵĻ
ŋŶťŨŮŦůŵġōņŅ
Őŏ
ŔŦŵŶű
ŃŶŵŵŰůġŔŰŶůť
ŐŇŇ
ŔŦŵŶű
ŖůŪŵġŰŧġŕŦŮű
ńŦŭŴŪŶŴ
Ɏ
ŔŦŵŶű
09 / 30 / 2007
09
30
ŃŢŤŬŭŪŨũŵ
łŭŸŢźŴ
ŔŦŵŶű
Őŏ
ŔŦŵŶű
ńŭŰŤŬġŔŦŵŵŪůŨ