User manual
Table Of Contents
- 1. About This Manual
- 2. General Information
- 3. Installation
- 3.1 Performing the Installation
- Step 1. Unpacking the StorageLoader
- Step 2. Installing the StorageLoader in a Rack
- Installing the Rack Mounting Kit
- Installing the “Rail Left Assembly”
- Installing the “Rail Right Assembly”
- Mounting the StorageLoader to the Rack
- How to dismount the StorageLoader from the rack
- Step 3. Connecting Power Cable
- Step 4. Removing the Transport Lock
- Step 5. Running Power-On Selftest
- Step 6. Setting the SCSI Address
- Step 7. Connecting the SCSI Bus Cable
- Step 8. Connecting the Ethernet Connector
- Step 9. Restarting Your System
- Step 10. BCR: Labelling of cartridges
- Step 1. Unpacking the StorageLoader
- 3.1 Performing the Installation
- 4. Operation and Configuration
- 1.
- 5. Remote Management
- 6. Maintenance
- 7. Troubleshooting
- Appendix A – Specifications
- Appendix B – Spare parts/Accessories
- Appendix C – Field Replacement Units (FRUs)
Tandberg Data Maintenance
Data cartridge incompatible with
drive
• Make sure you are using a data cartridges that is
compatible with the drive. See the tape drive’s reference
manuals for details.
• The SW backup application detects if an incompatible data
cartridge is used, and communicates this to the user.
• Remove the cartridge from the loader.
Cannot write to or read from
tape
• Make sure that the cartridge is write enabled (move the
write-protect switch to the enabled position).
• Make sure that the cartridge has not been written using an
incompatible format.
• Make sure that the cartridge is an acceptable format for
your drive type. See the tape drive’s reference manuals for
details.
• Make sure that the cartridge has not been exposed to
harsh environmental or electrical conditions and is not
physically damaged in any way.
• Many backup applications do not read or write to cartridges
that were created using a different backup application. In this
case, you may have to perform an erase, format, or label
operation on the cartridge.
• Make sure you understand any data protection or overwrite
protection schemes that your backup application may be
using, which could prevent you from writing to a given
cartridge.
• Retry the operation with a different, known good tape.
• Clean the tape drive. See chapter “Maintenance” in the
user and installation guide, section “using the cleaning
cartridge”.
SCSI problems
Changed drive SCSI ID, but the
host server system does not
recognize the new ID
• Make sure that all SCSI devices on the same bus have
unique ID numbers.
• If the SCSI bus is narrow (50-pin) only SCSI IDs 0 through
7 are available.
• Make sure that you reboot the StorageLoader after
changing the SCSI ID.
• Reboot the host server system.
The tape drive responds on the
SCSI bus to the host, but the
loader does not respond
•Verify that a SCSI terminator is attached to both the last and
first SCSI device on the SCSI bus.
• Verify that the SCSI cables are connected to the rear of the
loader. See chapter “Installation”, section “connecting the
SCSI bus cable”.
• Make sure that the correct host controller card is installed.
• Verify that the SCSI cables are not damaged and that the
total SCSI cable length is not exceeding the maximum
required length.
• Verify that the drive SCSI ID is set to an unique SCSI ID
that is not used by any other SCSI device on the same bus.
• Verify that the host application and the device drivers are
installed with the most resent patches to support the loader
• Reboot the loader by turning power off from the rear of the
loader and then on.
• Reboot the host system when the loader has completed its
power on sequence.
• Contact your service representative.
StorageLoader Installation and User Manual 57