Owner’ s Man ual Owner’s Manual Model Numbers: P/N 25121 Date 05-12-01 TCP-25, T CP-210 TCP-210 TCP-381 PUMPS TCP-210 Supplier To The Outdoor Power Equipment Industry ISM, Inc. • 1028 4th Street SW • Auburn, WA 98001 • Phone: (253) 333-1200 • Fax: (253) 333-1212 www.tanakapowerequipment.com custsvc@tanaka-ism.
TCP-25/210/381 Owner’s Manual Before using this unit: • • • Read the operator’s manual carefully. Check that the cutting equipment is correctly assembled and adjusted. Start the unit and check the carburetor adjustment. See “Maintenance”. WARNING The engine exhaust from this product contains chemicals known to the State of California to cause cancer, birth defects and other reproductive harm. Read, understand and follow all warnings and instructions in this manual and on the unit.
TCP-25/210/381 Owner’s Manual 1. What is What? Since this manual covers several models, there may be some difference between pictures and your unit. Use the instructions that apply to your unit. 1. Carrying Handle 2. Delivery Port 3. Priming Plug 4. Suction Port 5. Drain Plug 6. Throttle Lever 7. Base 8. Choke Lever 9. Recoil Starter 10. Air Cleaner 11. Fuel Tank 12. Fuel Cock www.tanakapowerequipment.com 2 custsvc@tanaka-ism.
TCP-25/210/381 Owner’s Manual 2. Warnings and Safety Instructions. Before operation • Protection is required for head, eyes, ears, hands and feet. Wear a suitable hard hat, goggles, ear covers, heavy gloves and safety shoes. • Dress properly, do not wear loose clothing or jewelry that could become caught in moving parts of the unit. • Never let a child or inexperienced person operate the machine. • Be sure to check bolts and other fasteners to see if any of them have become loose or are missing.
TCP-25/210/381 Owner’s Manual 3. Assembly Procedure Hose to pump connection. (Fig. 1-1) Care must be taken to ensure that tight connection is made between the female unions, and the male pump stubs. NOTE! An air leak at either union will greatly reduce the pump efficiency or no water is pumped at all. Strainer (Fig. 1-2) CAUTION! A strainer should always be used on the suction hose, to prevent debris from entering the pump body, and causing possible damage to the impeller. 4.
TCP-25/210/381 Owner’s Manual Priming (Fig. 2-2) It is necessary to prime the pump before the initial usage. This is done by filling the pump body with water via the priming plug on the top of the pump housing. CAUTION! Never start the machine without priming water in the pump. It will cause serious damages to the engine and pump parts, the manufacturer cannot guarantee in this case. Starting (Fig. 2-3, 3 B) *Open the Fuel cock (3). (TCP-381, Fig. 2-3B) 1. Set choke lever to CLOSED position (1). 2.
TCP-25/210/381 Owner’s Manual 5. Maintenance. Water pump (Fig. 3-1) All water in the pump should be drained from the housing, by means of the drain plug. Water left in the pump housing may cause damage by corrosion; there is also the danger of *freeze-up" damage in cold weather. NOTE! When the pump is used for the pumping of seawater, chemical fluid, or water which may contain any type of contaminant, the pump should always be "run through" with clean water prior to storage. Air filter (Fig.
TCP-25/210/381 Owner’s Manual Maintenance schedule Below you will find some general maintenance instructions. For further information please contact your service dealer. Daily maintenance • Clean the exterior of the pump. • Check that nuts and screws are sufficiently tightened. Weekly maintenance • Check the starter, especially cord and return spring. • Clean the exterior of the spark plug, • Remove the spark plug and check the electrode gap. Adjust it to 0.6 mm (.024’), or change the spark plug.
TCP-25/210/381 Owner’s Manual 6. Technical Data Model Engine Type Size Max Power Carburetor System Ignition System Spark Plug Fuel Tank Capacity TCP-25/210 TCP-381 High torque 2-cycle, single cylinder 22 ml 0.75 kW / 8,000 min-1 Walbro diaphragm Electronic NGK BPM-7A or BPMR-7A 0.75 l ! 51 ml 1.65 kW / 5,500 min-1 Float type ! NGK BM-6A or BMR-6A 1.2 l 120 l / min 8m 35 m 1” (25.4 mm) 300 l /min. 5m 40 m 1.5” (38 mm) 5.1 kg 287 x 219 x 288 mm 9.5 kg 398 x 300 x 382 mm 85.1 91.9 91.1 98.
TCP-25/210/381 Owner’s Manual Declaration of conformity We, Tanaka Kogyo Co.,Ltd.,3-4-29 Tsudanuma,Narashino,Chiba,Japan Declare under our sole responsibility that the product, engine pump model TCP-25,381 to which this declaration relates is in conformity with the essential safety requirements of directives. 89/392/EEC, 91/368/EEC, 93/44/EEC, 93/68/EEC, EMC89/336/EEC The following standards have been taken into consideration. Manufactured at: Chiba, Japan ISO 3864, (EN-292-2) Serial No.
