Illustr ated P ar ts Man ual Illustra Par arts Manual Model Number: HTS-2530PF 30” HEDGETRIMMER P/N 26607 Rev 000 Date 07-14-08 Nikko Tanaka Engineering U.S.A.,Ltd.• 1028 4th Street SW, Bldg B • Auburn, WA 98001 • Phone: (253) 333-1200 • Fax: (253) 333-1212 www.tanakapowerequipment.com custsvc@nikko-tanaka-usa.
PARTS INFORMATION HTS-2530PF CYLINDER, PISTON, CRANKSHAFT, IGNITION • FIGURE 1 ITEM 1-1 1-2 1-3 1-6 1-7 1-9 1-11 1-12 1-13 1-14 1-16 1-17 1-18 1-40 1-46 1-47 1-50 1-55 PART NUMBER 1570168090 0181166021 2550168020 0010300290 99461050184 0170300220 04101601200 0300300290 03900000201 03701700200 0460300280 99962091325 06810100200 1780300280 99416040186 1820186A201 1672174390 2500168020 DESCRIPTION CAP,SPARK PLUG ASS'Y PLUG,SPARK COVER,SPARK PLUG,RUBBER SET,CYLINDER BOLT,HEX,5X18,S GASKET,CYLINDER RING,PIS
PARTS INFORMATION HTS-2530PF FLYWHEEL, CRANKCASE • FIGURE 2 ITEM 2-19 2-19 2-19 2-19 2-26 2-31 2-32 2-33 2-34 2-35 2-36 2-37 2-51 2-52 2-53 2-54 2-55 PART NUMBER 33000200210 33000200220 33000200230 33000200240 2030300220 0720300290 99966122240 99961600100 0900300220 10002100200 99414050301 99414050451 1552174480 99210080012 99201080011 99101080011 2500168020 DESCRIPTION SHIM,12.2X19X.10 SHIM,12.2X19X.15 SHIM,12.2X19X.20 SHIM,12.2X19X.
PARTS INFORMATION HTS-2530PF CARBURETOR, FUEL TANK, FUEL SYSTEM www.tanakapowerequipment.com Page 3 • FIGURE 3 custsvc@nikko-tanaka-usa.
PARTS INFORMATION HTS-2530PF CARBURETOR, FUEL TANK, FUEL SYSTEM ITEM 3-25 3-26 3-27 3-30 3-33 3-35 3-36 3-37 3-38 3-39 3-40 3-41 3-43 3-44 3-45 3-46 3-50 3-51 3-52 3-53 3-54 3-55 3-58 3-70 3-77 3-78 3-79 PART NUMBER 4030300220 4040300290 99416050241 4020300220 99967015000 4230650081 47006500200 5280300220 99204080030 47601700200 99210050012 99011050602 4460650020 4520650091 3800637C200 4550300290 2230700090 68000731201 6750404280 5910300520 5950300290 65900801200 99463050185 44225143800 7000250408 700025
PARTS INFORMATION HTS-2530PF CLUTCH, STARTER, MUFFLER COMPONENTS • FIGURE 4 Recoil Starter Assy Use #762.03002.
PARTS INFORMATION HTS-2530PF CARBURETOR • FIGURE 5 A small retainer (560-0217020), has been added to this model after serial # A099801 to prevent the barrel end of the throttle wire from coming detached from the carburetor.
PARTS INFORMATION HTS-2530PF CLUTCH DRUM, GEAR CASE • FIGURE 6 www.tanakapowerequipment.com Page 7 custsvc@nikko-tanaka-usa.
PARTS INFORMATION HTS-2530PF CLUTCH DRUM, GEAR CASE • FIGURE 6 ITEM 6-1 6-2 6-3 6-4 6-5 6-6 6-7 6-8 6-9 6-10 6-11 6-16 6-19 6-21 6-22 6-23 6-26 6-27 6-29 6-30 6-31 6-32 6-43 6-60 6-71 6-72 PART NUMBER 3003318520 99351026002 99961600000 99961600002 2883318580 3063318520 3073318520 1013318580 1003318520 3033318520 99961608000 0853318520 2473318520 99461050254 30032250801 99051060183 99053060153 99200060011 0703318520 4623318520 99051040083 87132600200 99440060011 3013318520 99210060012 99440060011 DESCRIP
PARTS INFORMATION HTS-2530PF HANDLE, CUTTER BLADES • FIGURE 7 ITEM 7-12 7-12 7-13 7-14 7-17 7-18 7-24 7-25 7-25 7-28 7-39 7-40 7-41 7-42 7-42 7-44 7-45 7-46 7-49 PART NUMBER 1223318720 1223328520 1363318120 99052060253 1213318720 1203318720 12933202201 1243320221 1243228720 1283790420 12533202205 0513318581 1653759020 1233317A20 40927 99201060011 99210060012 99201060011 1383321520 DESCRIPTION GUIDE,CUTTER 30" GUIDE,CUTTER 30" PLATE,PROTECTION SCREW,HEX HOLE 6X25 BLADE,B,SS,30" BLADE,A,SS,30" WASHER,7 B
PARTS INFORMATION HTS-2530PF HANDLE, THROTTLE COMPONENTS • FIGURE 8 www.tanakapowerequipment.com Page 10 custsvc@nikko-tanaka-usa.
PARTS INFORMATION HTS-2530PF HANDLE, THROTTLE COMPONENTS • FIGURE 8 ITEM 8-1 8-2 8-3 8-4 8-5 8-6 8-7 8-10 8-13 8-14 8-15 8-16 8-17 8-18 8-19 8-22 8-23 8-24 8-25 8-33 8-35 8-36 8-75 8-76 PART NUMBER 0533323122 0543323123 23033210201 23133210200 06132600201 1703318980 9253253020 7653212020 99416040301 99416040251 0553318990 0503318580 8850650J80 1641001500 99416040161 99178040010 99011030101 2581165020 19833130200 99461050124 0583318520 0603318520 81320000200 03629331501 DESCRIPTION GRIP,HANDLE"A" GRIP,HA
PARTS INFORMATION HTS-2530PF DECALS • FIGURE 9 ITEM PART NUMBER DESCRIPTION 9-1 9060300521 DECAL,MODEL,HTS-2530PF 9-17 9203246620 DECAL,CAUTION www.tanakapowerequipment.com Page 12 QTY 1 1 COMMENTS custsvc@nikko-tanaka-usa.
TECHNICAL SERVICE BULLETIN NUMBER PI 3118 Date: June 2001 Model & Serial: THT-2100/THT-2120/THT-2510/THT-2520/THT-2540/HTD-2522PF/HTD-2526PF/HTD2530PF/HTS-2530PF. All units produced after serial number W100101. Reason: When these units are fitted with the aluminum safety shield, some experience loosening of the blade jam nuts. A flat washer has been added between the nut and the aluminum shield to help prevent the nut from becoming loose.
TECHNICAL SERVICE BULLETIN NUMBER PI 3119 Date: January, 2002 Model & Serial: All THT, HTD, HTS, TPH hedgetrimmer models. All units after serial number Y004401 Reason: All future production of hedgetrimmer models will utilize a blade-retaining nut that is of the locking variety. These nuts are oblong on one side to prevent loosening during use, but can be removed and re-installed without losing their locking ability.
TECHNICAL SERVICE BULLETIN NUMBER PI 3121 Date: September 2002 Model & Serial: HTD-2522PF / 2526PF / 2530PF / HTS-2530PF All units after serial number Y210151 Reason: Exhaust gas flow from these models in some circumstances can cause scorching of leaves during cutting due to the direction of the tail pipe outlet. The direction of flow from the muffler has been re-directed to exit horizontally rather than vertically.
TECHNICAL SERVICE BULLETIN NUMBER PI 3130 Date: December 2004 Model & Serial: TPH-210/2501/250PF270PF – A290201 and later. HTD-2522PF/2526PF/2530PF, HTS-2530PF/2540PF – A302051 and later. THT-2120/2520/2540 – A302051 and later. Reason: Configuration standardization of hardware, converting blade hardware from US Standard thread to Metric thread. Comments: Please verify serial number on unit prior to ordering replacement blade hardware and add the support plate on older serial numbers.
