Adapter for PluX22and 21MTC-Interface Item number 70-01045 ta m s el ek tro ni k Manual PluX22 NEM 658 | RCN-122 NEM 660 | RCN-121 tams elektronik n n n
Adapter for PluX22- and 21MTC-Interface tams elektronik Contents 1. Getting started.............................................................................................................3 1.1. Contents of the package.......................................................................................3 1.2. Accessories..........................................................................................................3 1.3. Intended use..........................................................
tams elektronik Adapter for PluX22- and 21MTC-Interface 1. Getting started This manual gives step-by-step instructions for safe and correct assembly of the kit and fitting and connecting of the adapter, and operation. Before you start, we advise you to read the whole manual, particularly the chapter on safety instructions and the checklist for trouble shooting. You will then know where to take care and how to prevent mistakes which take a lot of effort to correct.
Adapter for PluX22- and 21MTC-Interface tams elektronik 2. Operation overview The adapter is used to upgrade vehicles with a PluX or MTC interface interface. There is a 22pole socket soldered on to the adapter PCB which is used to insert the plug connector of the decoder-sided PluX interface. In order to connect the adapter to the the decoder-sided MTC interface, the extra 22-pole plug connector has to be inserted into the adapter PCB. 2.1.
tams elektronik Adapter for PluX22- and 21MTC-Interface 2.3. Mounting versions for PluX decoders Mounting version 1: Inserting direction of the decoder: from above k Mounting version 2: Inserting direction of the decoder: from below el ek tro Mounting version 1 a: Inserting direction of the decoder: from above + Socket terminal strip of the decoder on top ni 2.4.
Adapter for PluX22- and 21MTC-Interface tams elektronik 3. Assembling the kit 3.1. Safety instructions Mechanical hazards Cut wires can have sharp ends and can cause serious injuries. Watch out for sharp edges when you pick up the PCB. Visibly damaged parts can cause unpredictable danger. Do not use damaged parts: recycle and replace them with new ones. Fire risk ni k Touching flammable material with a hot soldering iron can cause fire, which can result in injury or death through burns or suffocation.
tams elektronik Adapter for PluX22- and 21MTC-Interface 3.2. Safe and correct soldering ! Caution: Incorrect soldering can cause dangers through fires and heat. Avoid these dangers by reading and following the directions given in the chapter Safety instructions. Use a soldering iron with temperature control, which you set to approx. 300 °C. Solder quickly: Soldering for too long can detach solder pads or tracks or even destroy components.
Adapter for PluX22- and 21MTC-Interface tams elektronik 3.3. Soldering on the cables Solder the connecting cables on the top side of the adapter PCB. Observe the different assignments for PluX and MTC interfaces and the different mounting versions. It is recommended to use cables of different colours according to NEM 658 or NEM 660 in order to avoid mistakes when connecting the adapter PCB. Perform a visual check! After having soldered the cables you should perform a visual check and remedy defects.
Adapter for PluX22- and 21MTC-Interface Cable colour Pin Name Description Plux adapter 1 GPIO/C Universal input/output 2 AUX3 Output 3 3 GPIO/B Universal input/output, train-bus pulse 4 GPIO/A Universal input/output, train-bus data 5 GND Decoder ground, pick-off after rectifier 6 V+ Cap.
Adapter for PluX22- and 21MTC-Interface tams elektronik 3.5. Assignment for 21MTC adapters (NEM 660/RCN-121) In order to avoid damage due to a connection of the decoder with reversed polarity, you sould remove the index pin (pin 11) at the 22-pole plug connector. You can withdraw the pin with small pliers.
Adapter for PluX22- and 21MTC-Interface Description MTC adapter 1 Input1 Sensor input 1 2 Input2 Sensor input 2 3 AUX6 Output 6 4 AUX4 Output 4 5 ZBCLK Pulse generator train bus 6 ZBDTA Data train bus (TxD, RxD) 7 F0r Lighting forward direction 8 F0f Lighting backward direction 9 LS/A Loudspeaker connection A 10 LS/B Loudspeaker connection B 11 Index not in use, coding 12 Vcc 13 AUX3 14 AUX2 15 AUX1 tro yellow white brown brown el ek V+ ta m 16 Cable colour
Adapter for PluX22- and 21MTC-Interface tams elektronik 4. Checklist for troubleshooting and error correction ! Warning: If you notice a strong heat development, immediately disconnect the connection to the supply voltage. Fire hazard! Possible causes: The connecting cables on the PCB are badly assigned to the connections of the decoder or the vehicle. à Perform a visual check and remedy defects. Damage on the decoder or the vehicle cannot be excluded.
tams elektronik Adapter for PluX22- and 21MTC-Interface Carrying out the repair(s) By sending in the product(s), you give us the order to inspect and repair it. We reserve the right to refuse the repair if it is technically impossible or uneconomical. In the event of a warranty or guarantee claim, you will then receive a replacement free of charge. Cost estimates Repairs for which we charge less than € 25.00 per item plus shipping costs will be carried out without further consultation with you.
Adapter for PluX22- and 21MTC-Interface tams elektronik 6. Warranty, EU conformity & WEEE 6.1. Guarantee bond For this product we issue voluntarily a guarantee of 2 years from the date of purchase by the first customer, but in maximum 3 years after the end of series production. The first customer is the consumer first purchasing the product from us, a dealer or another natural or juristic person reselling or mounting the product on the basis of self-employment.
tams elektronik Adapter for PluX22- and 21MTC-Interface 6.2. EU Declaration of Conformity This product fulfils the requirements of the following EU directives and therefore bears the CE marking. 2001/95/EU Product Safety Directive 2015/863/EU on the restriction of the use of certain hazardous substances in electrical and electronic equipment (RoHS) 2014/30/EU on electromagnetic compatibility (EMC Directive).
k ni tro el ek Further Information and Tips: ta m s http://www.tams-online.de Warranty and Service: tams elektronik GmbH Fuhrberger Str. 4 30625 Hannover / GERMANY Phone: +49 (0)511 / 55 60 60 Fax: +49 (0)511 / 55 61 61 Email: support@tams-online.
