Series Installation Guide
Table Of Contents
- Introduction
- Customer Support
- Tools Required
- Components List
- Pre Assembly for Models STP-LCR/82HW STP-LCR/124HW
- Step 1: Connecting Panel Support Channels (STP-LCR/124HW only)
- Step 2 Connecting inner\outer brace channels
- Step 3: Connecting Panels to Panel Supports
- Final Assembly
- Step 4: Attach Pole Clamp Assembly to Pole
- Step 5: Attach Tilt Plate Mounting Channel
- Step 6: Attach Tilt plates
- Step 7: Attach Cross Rails to Tilt Plates.
- Step 8: Attach Panel Support Sub Assembly to Cross Rails
- Step 9: Install Knee Brace Cross rail STP-LCR/82HW STP-LCR/124HW
- Step 10: Adjust Tilt Angle
- Step 11: Install Lower Vee Brace STP-LCR/82HW STP-LCR/124HW
- Detailed Diagrams for Assembly
- Foundation Hole Guidelines (see charts pages 14, 15)
- Footing Chart 2 panel STP-LCR/82HW
- Footing Chart 3 panel STP-LCR/124HW
- Installer Responsibility
- Warranty Information
STP HW Mount
Series
2
82HW 124HW
PART NUMBER DESCRIPTION QTY. QTY.
51-04PC-012 REV A 4" Pipe Clamp Half 2 2
51-04CH-012 REV A Clamp Strong Back Cap 1 1
51-04BC-TLT REV A Channel, Tilt Plate Mounting 2 2
51-04TP-LR2 REV C TILT PLATE L/R 2 2
51-07CR-058 REV C Cross Rail, 58 Inch 3
51-04CR-R60 REV B Rail, 60 in Cross 3
51-07TC-056 REV B Panel Support Section 56 inch 2
51-07TC-068 REV B Panel Support Section 68 inch 2
51-07CN-030 REV D Connector, 30" 2
51-04TC-082 REV D Panel Support TP 82 inch 2
51-0534-HWI rev A Channel, Inner Brace 34.5" 2 2
51-0534-HWO rev A Channel, Outer Brace 34.5" 2 2
51-06HW-015 rev A INNER SWIVEL BRACKET 2 2
51-06HW-020 rev A OUTER SWIVEL BRACKET 4 4
51-STPB-000 REV A LOWER BRACE ANGLE BRACKET 2 2
51-SPCB-4BC REV A 4" PIPE CLAMP (BOTTOM) 1 1
23-0100-040 Bolt, U 3/8 4 1/2"x6" ID HDG 2 2
25-3702-GLV Washer, Flat 3/8" HDG 4 4
25-3701-GLV Washer, lock 3/8" HDG 4 4
24-3716-GLV Nut, 3/8-16 Hex HDG 4 4
23-3716-100 Bolt, 3/8-16 x 1.0 Hex SST. 16 16
25-3702-000 Washer, Flat 3/8" SST. 32 32
25-3701-000 Washer, lock 3/8" SST. 16 16
24-3716-440 Nut, 3/8-16 Hex SST. 16 16
27-0456-700 Rod, threaded, SST 5/16-18 x 7" long 4 4
23-3118-350 BOLT Hex 5/16-18 x 3.5" SST 6 6
23-3118-850 Bolt, 5/16-18 x 1.0 Hex CS SS 1 1
23-3118-875 Bolt, Hex 5/16-18 x .875 SST 12 20
25-3102-000 Washer, flat 5/16" SS 19 27
25-2501-015 Nut, flange 5/16 SST 35 43
23-2520-050 Bolt, Hex 1/4-20 x .75 SST 24 28
25-2502-000 Washer, flat 1/4 SS 32 40
25-2501-000 Washer, lock 1/4" 8 12
24-2520-440 Nut, 1/4-20 fin hex SS 8 12
25-2501-014 Nut, Flange Serrated 1/4-20 SST 16 16
Tools Required
Tools that support the following size hex heads: Torque values are “dry”, add 15% if using anti-seize lubricant on
stainless hardware (Recommended). Deep sockets for 5/16” and 1/2”, long combination wrench for 5/16.
1. 3/8” = 240\20 In\Ft Lbs
2. 5/16”= 144\12 In\Ft Lbs
3. 1/4" = 84\7 In\Ft Lbs
Components List
The following parts are used on the
STP-LCR/82HW STP-LCR/124HW
mount models:
Galvanized coated sheet steel components will show rust on cut edges and is normal and will not affect
the
structure and function of the mount.