USER MANUAL Global Positioning System takeMS Navigation System traffix 43/35 1
Safety Information....................................................................................................... 3 Installation ................................................................................................................. 5 Views .......................................................................................................................... 9 Front View ..........................................................................................................
SAFETY INFORMATION Safety Instructions Please read this section carefully and follow all the instructions given. This will help ensure reliable operation and extend the service life for your appliance. Keep the packaging and the user instructions for future reference or inquiries at a later date. If you pass the article on to another person, you must pass on these instructions. Never open up the housing of the appliance or the power adapter. These contain no user-serviceable parts.
only screened cable (maximum 3m/10ft) should be used with this appliance. For optimal performance, maintain a distance of at least 3m/10ft. from sources of high-frequency and magnetic interference (televisions, loudspeaker systems, mobile telephones and so on.) This will help avoid malfunctions and loss of data.
Connection When connection your appliance be sure to correctly observe the following instructions: ● The outlet must be in the vicinity of the appliance and must be easily accessible. ● Only use the mains adapter on grounded sockets at 100-240V~AC, 50/60Hz. If you are unsure about the power supply to the place of use, ask the relevant energy supplier. ● Use only the power adapter provided with your appliance.
of the navigation system. 2 1 Push the adapter connector into the guide on the right of the network adapter. Push the Network Adapter (2) into a power point that is easily accessible. Push the cable of the Network Adapter (1) into the network adapter connection of the navigation system. Working with memory cards Your navigation system supports MMC and SD memory cards. Inserting memory cards 1. Carefully take the memory card out of its packing (if included). Take care not to touch or dirty the contacts. 2.
Soft Reset This option restarts the navigation system, without reinstallation being necessary. A soft-reset is often used in order to reorganize the memory. In doing so all programs that are running are interrupted and the working memory is reinitialized. Choose this option if your navigation system is not responding or working properly. Perform the soft-reset as follows: Screw off the end cap of the pointer and carefully press the point of the end cap into the reset opening on the left side of your device.
Mounting The Navigation Set In A Car Attention! Only fix the holder for the navigation system to the windscreen, if it does not impede the view. Should this not be possible, Then mount the holder with the enclosed suction plate in any way that will allow peril-free and safe operation. Installation Of The Holder Of The Navigation System ● Hint: If you want to fix the holder to the wind screen, then you can skip steps 1 and 2. 1. Remove the protective foil from the sticky side of the suction plate. 2.
Connecting The Navigation System In The Car δ When the battery is in a low voltage, you can recharge it in the car: 1. Plug the jack (1) of the connection cable into the corresponding receptor at the bottom of your navigation system . 2. Insert the power adapter (2) now into the cigarette lighter socket and ensure, that it will not lose contact while driving. This could cause a malfunction.
BACK VIEW 2.Stylus Take the pen out of its compartment in order to use it, and replace it after use. The pointer pen is required for operating the touch screen. 3. Reset Button Press it to reset the system. 4. Loudspeaker Playback language statements and warnings. VIEWS TOP/BOTTOM VIEW 5. USB Interface Interface for connecting to a PC by means of the ActiveSync Cable (for data matching). 6.Sleep/Wake up Button Press and hold Sleep/Wake up button for about two seconds to Wake up the unit.
LEFT/RIGHT VIEW 7. AC Adaptor Port Connection to external power supply. 8. External Aerial Interface Interface for an optional second aerial. 9. Volume+/-, Lock/Unlock Screen Switch Volume+/- to adjust the volume level. Press and hold it to Lock/Unlock the touch screen. 10. Battery On/Off Switch Switch it to Lock/Unlock position to turn the power On/Off. 11. SD/MMC slot Accepts an optional SD (Secure Digital) or MMC (Multi Media Card) Card for removable storage. 12.
Memory Card Quick Installation This option is only available to you if your navigation system is equipped with a prepared memory card. In this case, you will ready be able to use the Navigation function of your device after a short time, without carrying out the pre-installation on a PC. ● The initial setting up must be carried out as described ● The following installation limits the Navigation to the area which is pre-installed on your memory card.
Software Installation On Your PC In order to be able to deploy self-defined cards on your navigation system you must install the corresponding navigation software on your PC. 1. Before installing the navigation software ensure that ActiveSync is installed and your navigation system is connected with your PC via the ActiveSync-cable. 2. Place the CD 1 with the navigation software in your CD drive. The installation will start automatically. 3. Follow the program instructions.
