User's Manual
Table Of Contents
- Installation and Operation Manual
- Tait Contact Information
- Contents
- Preface
- 1 Introduction
- 2 Mechanical Description
- 3 Functional Description
- 4 Installation
- 5 Replacing Modules
- 5.1 Removing the Base Station and Opening the Tray
- 5.2 Replacing the UI Board
- 5.3 Replacing the Receiver Module
- 5.4 Replacing the Transmitter Module
- 5.5 Replacing the SI Board
- 5.6 Replacing the Transmitter and Receiver Fans
- 5.7 Replacing the Fan Power Board
- 5.8 Replacing the Temperature Sensor Board
- 5.9 Replacing the AC Power Supply Unit, Fan and Filter Module
- 5.10 Replacing the Speaker
- 5.11 Final Reassembly
- 6 Connections
- 7 Preparation for Operation
- 7.1 Introduction
- 7.2 Mode of Operation
- 7.3 Line-controlled Base
- 7.4 Talk Through Repeater
- 7.5 RF Modem
- 7.6 Data Repeater
- 7.7 TaitNet Trunking
- 7.8 Programmable Features
- 7.9 Additional Settings
- 7.10 Adding Subaudible Signalling
- 7.11 Soft Off (Tx Tail Time)
- 7.12 Tone On Idle (TOI)
- 7.13 Fan Operation
- 7.14 Channel ID
- 7.15 Relay Polarity
- 7.16 Channel Increment and Decrement by Function Keys
- 7.17 Carrier Wave Identification (CWID)
- 8 Maintenance Guide
- Glossary
- Tait General Software Licence Agreement
- Directive 1999/5/EC Declaration of Conformity
TB7100 Installation and Operation Manual Preparation for Operation 111
© Tait Electronics Limited December 2005
Receiver
Digital IO
The user-defined settings for the receiver digital IO are shown below.
The cells in grey denote mandatory settings.
Transmitter
Digital IO
The user-defined settings for the transmitter digital IO are shown below.
The cells in grey denote mandatory settings.
Receiver Audio The user-defined settings for the receiver audio IO are shown below.
The cells in grey denote mandatory settings.
Pin Direction Label Action Active Debounce
Signal
State
Mirrored
To
AUX_GPI1 Input BIN_0 BCD_Pin_0 Low 10 None None
AUX_GPI2 Input BIN_1 BCD_Pin_1 Low 10 None None
AUX_GPI3 Input BIN_2 BCD_Pin_2 Low 10 None None
AUX_GPIO4 Input BIN_4 BCD_Pin_3 Low 10 None None
AUX_GPIO5 None RX_DO_1 No Action Low None None None
AUX_GPIO6 None RX_DO_2 No Action Low None None None
AUX_GPIO7 Output RXGATE Busy Status High None None None
Pin Direction Label Action Active Debounce
Signal
State
Mirrored
To
AUX_GPI1 Input BIN_0 BCD_Pin_0 Low 10 None None
AUX_GPI2 Input BIN_1 BCD_Pin_1 Low 10 None None
AUX_GPI3 Input BIN_2 BCD_Pin_2 Low 10 None None
AUX_GPIO4 Input BIN_4 BCD_Pin_3 Low 10 None None
AUX_GPIO5 None TX_DO_1 No Action Low None None None
AUX_GPIO6 None TX_DO_2 No Action Low None None None
AUX_GPIO7 Input TXKEY External PTT
1
High 2 None None
Rx/PTT Type Tap In Tap In Type
Tap In
Unmute
Tap Out
Tap Out
Type
Tap Out Unmute
Rx None A-Bypass In On PTT R4 D-Split Busy detect +
Subaud
Mic PTT None A-Bypass In On PTT None C-Bypass Out On PTT
EPTT1 None A-Bypass In On PTT None C-Bypass Out On PTT
EPTT2 None A-Bypass In On PTT None C-Bypass Out On PTT