2 FT × 12 FT STEEL BEAM GAZEBO MODEL #TPGAZ2009
PACKAGE CONTENTS A R2 J1 D B J2 D C R1 C1 E F G P K Q L P1 M S1 O N S2 PART PART DESCRIPTION DESCRIPTION QUANTITY PART PART A B C C1 D E F G J1 J2 L Decoration Ball Small Center Connector Large Center Connector Hook Small Top Bar Long Top Bar Connector Short Top Bar Left Long Bar Right Long Bar Mosquito Net Pipe 1 1 1 1 4 4 4 4 4 4 8 M N O P P1 Q R1 R2 S1 S2 1 DESCRIPTION Post Base Plate Cover Connector Hang Ring Corner Connector Large Roof Small Roof Mosquito Net Sidewall QUANTIT
HARDWARE CONTENTS (shown actual size) T M6 × 15 mm Qty. 8 U M6 × 15 mm Qty. 48 X Y Wrench Qty. 2 Wrench Qty. 1 V M6 × 32 mm Qty. 8 Z W M6 × 15 mm Qty. 4 II Stake Qty. 16 2 allenandroth.
SAFETY INFORMATION Please read and understand this entire manual before attempting to assemble or install the product. . Two to four people are need for assembly. . Maximum load for the roof hook: 50 lbs. WARNING: . KEEP ALL FLAME AND HEAT AWAY FROM THIS TENT FABRIC. . This tent meets the flammability requirements of CPAI-84. The fabric may burn if left in continuous contact with any flame source.
INSTALLATION INSTRUCTIONS 2 2. Insert the right long bar (J2) into the left long bar 2 2 (J1). Secure together using M6*15 mm bolt (T). Repeat the procedure for the other right long bar (J2) and the left long bar (J1). Tighten securely with the wrench (X). J2 J1 T J1 J2 Hardware Used T T M6 × 15 mm X Wrench 3 3. Secure the crossbar (J1/J2)assemblies to the post (M) using M6*15 mm bolts (U).
INSTALLATION INSTRUCTIONS 4. Fix the corner connector (Q ) and the post (M) together by the screw M6*15mm (W). Fix the mosquito net pipe (L) and connector (P) to the bars (J1/J2) by the screw M6*15mm (U). Tighten securely with the wrench (X). 4 4 P W U L L U U U L L J1 Hardware Used U Q J2 J2 M6 × 15mm Bolt P L Q J1 Q L L J2 W M6 × 15mm Bolt J1 J2 L L X Wrench Q L J1 P P L J2 P Q L J1 Y J1 Wrench 5. Insert each connector (F) into each long top bar (E).
INSTALLATION INSTRUCTIONS 7.Insert the long top bar (E) into the 7 large center connector (C), connect 4 the connector pipe (F) with the long top bar (E), then fix the connector pipe (F) and the corner connector (Q) together by the screw M6*32mm (V). Tighten securely with the wrench(X). C E G E V E E H F Q E Q J2 J1 E J1 J2 F F Hardware Used E G E Q J2 J1 Q J2 J1 M6 × 32mm Bolt F Q V Wrench 8.
INSTALLATION INST RUCTIONS 9 9. Insert each small top bar (D) into the small center connector (B). Attach the small roof (R2) on the small top bar (D), then secure with the decoration ball (A). D D B A R2 B O R2 O R2 OD 10. Put the large roof (R1) on the top bar shaft. 10 O R1 OF G R1 7 7 allenandroth.com allenandroth.
INSTALLATION INSTRUCTIONS 11. Connect the small top bar (D) with the large top bar (E). 11 D E 12. Hang the mosquito net (S1) onto inside 12 4 of the mosquito net pole, hang the sidewall (S2) onto outside of the mosquito net pole, as shown. 2 1 S1 8 S2 allenandroth.
INSTALLATION INSTRUCTIONS 13. Move the cover (O) upward, fix the base plate (N) by the stake (Z), then move the cover (O) down. 13 4 Hardware Used Z Stake X M O Z N 9 allenandroth.
