Troubleshooting Guide
© 2022 Target. The Bullseye Design is a registered trademark of Target Brands, Inc. All rights reserved.
WARNING:
CHOKING HAZARD—Small parts.
Not for children under 3 years.
Wireless
Speaker
Pairing:
1. Power ON the speaker.
2. The indicator light will ash blue when
it is ready to pair.
3. Use the Bluetooth settings on your
device to pair with target TB speaker 01
4. When pairing is successful the blue
light will turn solid and there will be a
chime.
5. The speaker will automatically recon-
nect to the device it was most recently
paired to when you turn the speaker on
and it is in Bluetooth mode.
Audio Indicators:
• Ascending tones - Powering on
• Single chime - Ready to pair
• Echoing chime - Paired
• Low tone - Max/Min. volume
• Quick descending tone - AUX connected
• Descending tones - Power o
Charging:
1. A full charge requires approximately
4-4.5 hours.
2. Open the panel on the side of the
speaker and plug the USB-C end of the
charging cable into the charge port.
3. Plug the opposite end of the
charging cable into a power supply of
at least DC 5V 1A.
4. Charging is complete when the red
light turns o.
Warning: Please use UL compliant
power supply.
AUX/Line in:
1. If the power is turned on, plug in
the 3.5mm audio cable to override
Bluetooth, the speaker will play
automatically.
2. If the power is turned o, plug in
the 3.5mm audio cable to override
Bluetooth, and press the M button to
switch to AUX.
Included:
1. Bluetooth Speaker
2. USB-A to USB-C Charging Cable
FCC ID: 2AO23-BTSP1S Model: BTSP1S Input: 5V 1A Max Made in China
This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: 1) this device may not cause harmful interference, and 2) this
device must accept any interference received, including interference that may cause undesired operation. Warning: Changes o
r modifications to this unit not
expressly approved by the party responsible for compliance could void the user,s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of the following
measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a
circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help.
The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.
Target Corp. Mpls. MN, 55403 Phone: 1-612-304-6073
Troubleshooting:
1. If the speaker is not working
correctly, turn it on/o to restart.
2. If the speaker won’t turn on,
recharge the battery and try
again.
3. If the speaker won’t charge,
make sure the supply works, is
5V>1A, and not damaged.
4. If the speaker makes no sound
or does not show as an available
device, make sure it is not
paired, if so unpair the device
and repair the desired device.
5. If the speaker cannot be
operated despite being turned
on, hold the power button for 8
seconds to reset.
Safety:
1. Do not expose the product to re,
high temperature, direct sunlight, etc.
2. Do not modify or repair this device.
3. Do not allow small particles to get
into the product.
4. Do not use chemical detergents to
clean, use a soft dry cloth.
1. You can pair two of this model of
speaker together.
2. Turn Bluetooth o on your device,
place two matching speakers together,
power them on.
3. Press “+-” at the same time on one
speaker and they will pair automatically.
4. On your device turn Bluetooth on,
and pair to one of the speakers.
5. When no music is being played the
indicator will ash blue on the speaker
that is the left channel and will be solid
blue on the speaker that is the right
channel.
6. To maintain TWS pairing turn
Bluetooth o on your device before
powering the speakers back on, the
speakers will pair automatically, then
repair with your device.
TWS (True Wireless Stereo) pairing
11in
9.92in
Side
Press: Play/Pause
Hold: On/O
(2 seconds)
Press:
Answer/end calls
Switch modes:
Bluetooth, AUX
Hold: Reject call
Indicator light:
• Solid Red - Charging
• No Red Light - Fully charged
• Flashing Blue - Pairing
• Solid Blue - Paired
• Rapid Flashing Blue
- Max/Min Volume
AUX in port
Press: Vol. down
Hold: Prev. track
(Bluetooth mode
only)
Press: Vol. up
Hold: Next track
(Bluetooth mode
only)
Power level
Indicator lights
Charge input/
USB-C port