OPERATION MANUAL Project60.2P PROJECT60.2P PROT CL IP POWER SIGNAL CH 1 CH 2 Please follow the instructions in this manual to obtain the optimum results from this unit. We also recommend that you keep this manual handy for future reference.
V1.0-09-11-27 TABLE OF CONTENTS 1. SAFETY PRECAUTIONS .......................................................................................3 2. GENERAL DESCRIPTION ....................................................................................5 3. FEATURES ...............................................................................................................5 4. NOMENCLATURE AND FUNCTIONS 4.1 Front Panel .....................................................................................
1. SAFETY PRECAUTIONS Be sure to read the instructions in this section carefully before use. Make sure to observe the instructions in this manual as the conventions of safety symbols and messages regarded as very important precautions are included. We also recommend you keep this instruction manual handy for future reference.
1. SAFETY PRECAUTIONS When Installing the Unit Never plug in nor remove the power supply plug with wet hands, as doing so may cause electric shock. When unplugging the power supply cord, be sure to grasp the power supply plug; never pull on the cord itself. Operating the unit with a damaged power supply cord may cause a fire or electric shock. When moving the unit, be sure to remove its power supply cord from the wall outlet.
2. GENERAL DESCRIPTION With two separate power amplififers in a single chassis and power ratings 60 watts RMS, these sleek, attractive units provide a compact solution for t&mSystems system amplification and distribution. 3. FEATURES 1. 2. 3. 4. 5. 6. Rated outputs 60W . 100V/70V/50V line transformer-isolated speaker outputs, low impedance 4 ohms speaker outputs. 2 independent amps in a singale chassis. LED status indicators. Volumre controls for each channel.
4. NOMENCLATURE AND FUNCTIONS 4.1 FRONT PANEL 5 6 PROJECT60.2P 4 3 PROT CL IP POWER SIGNAL CH 1 1 1. POWER SWITCH On top of the opening Power Press the end, power shut down 2. CH1\CH2 VOLUME volume control(CH1.CH2) 3. SIGNAL Signal indicator(CH1.CH2) CH 2 2 4. CLIP Clipping indicator(CH1.CH2) 5. PROT Protection indicator(CH1.CH2) 6. POWER Power indicator Project60.
NOMENCLATURE AND FUCTIONS 4.2 REAR PANEL 17 CH2 LINK 16 15 CH1 LINK CH2 INPUTS 2 14 CH1 INPUTS 1 2 3 1 2 1 3 3 XLR BAL 1-GND 2-HOT+ 3-COLD- ~230V/50Hz T3.15AL 250V ¦¸ 4 COM 50V 100V PUBLIC ADDRESS SYSTEM SERIAL NO : 70V 4 POWER OUT1 COM 50V 100V 70V POWER OUT2 ¦¸ CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN AVIS: 10 11 12 10.COOLING FANS 11.~ 230V/50Hz AC POWER INPUT 12.POWER OUT2 Connectors for 4 ohms or 50V and 70V and 100V speaker 13.
5. CONNECTIONS SPEAKER CONNECTIONS COM 4 50V 70V 100V COM 4 50V 70V 100V COM 4 50V 70V 100V 81 42 4 COM 4 50V 50V LINE 70V 70V LINE 100V 167 100V LINE 50V and 70V/ Project60.
6. MACHINE OPERATION MIC INPUT CHANNEL 1~3 This is a special connector which will accept 3-conductor XLR. These inputs are suitable to receive signal from microphones level devices. MIC JACK (XLR JACK) LINE JACK (TRS PHONE JACK) Pin 1:GROUND Sleeve:GROUND Pin 2:HOT(+) Tip:HOT(+) Pin 3:COLD(-) Ring:COLD(-) 1.GROUND 2 3 1 1 2.HOT 3 2 3.COLD CH1/CH2 INPUTS COLD 1.GROUND 2.HOT 3.
INSIDE AC/DC FUSE 240AC 240/50Hz MAX 9.9W DC POWER 24V MAX 0.6A 2--OUTPUTS--1 INPUTS LINE 10 RISK OF ELECTRIC SHOCK DO NOT OPEN REC LINE 8 RISQUE DE CHOC AVIS: -NE PAS QUVRIR LINE 9 LINK ELECTRICUS LINE 7 LE FT 10 9 MIC INPUTS 8 2 3 1 7 3 2 PUBLIC ADDRESS S YSTEM 6 1 MODEL NO: T-2S01 4 T5AL 250V AC~230V 50~60Hz 3 SERIAL NO: 2 GND PRIORITY CHIME LED PWR 1 2 3 MIC INPUT 7 6 3 1 524 CHIME REMOTE P.T.T 1 4 5 6 7 ~230V/50Hz T3.
Project60.2P CH1 INPUTS CH1 LINK CH2 INPUTS CH2 LINK EB EB Z POWER PA PA PT TO TO COM 100V 70V 50V 4 COM 100V 70V 50V 4 ~230V AC 50Hz 8.
9. SPECIFICATIONS Project60.2P MODEL RATED POWER OUTPUT SPEAKER OUTPUTS INPUT SENSITIVITY FREQUENCY RESPONSE 2X60W 4 ,50V/70V/100V 775mV/0dB 50Hz~15KHz+ - 3dB S/N RATIO >90dB T.H.D <1% RADIATOR METHOD Compulsive wind cooling INDICATORS Power, Signal, Protection and Overheat PROTECTION Power,Overheat, Overload and short-circuit POWER REQUIREMENTS ~230V/50Hz POWER CONSUMPTION 220W DIMENSION(mm) 484X448X88 NET WEIGHT 12Kg GROSS WEIGHT 14.2Kg Project60.
10.DIMENSIONAL DIAGRAM UNIT :mm 484 PROJECT60.2P CL IP SIGNAL CH 1 CH 2 94 84 PROT POWER 436 CH1 LINK CH2 INPUTS 2 CH1 INPUTS 1 2 3 1 2 1 3 3 XLR BAL 1-GND 2-HOT+ 3-COLD- 84 CH2 LINK ~230V/50Hz T3.15AL 250V ¦¸ 4 50V 70V COM PUBLIC ADDRESS SYSTEM SERIAL NO : 100V 4 50V 70V POWER OUT1 COM 100V POWER OUT2 ¦¸ CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN AVIS: RISQUE DE CHOC ELECTRICUS -NE PAS QUVRIR 423 417 84 25 6 PROJECT60.
PUBLIC ADDRESS SYSTEM 2009-11 Version1.
