User's Manual
Operation Keyboard: Main Menu Phone 1st Phone, enter into phone
number setup menu.
Press to select Number, input the alarm number (up to 18 digits),
and press to backspace in case of error
Press to select Dial, press to select On or Off.If "On" is selected,
the panel will dial the alarm number when an alarm occurs.
Press to select SMS, press to select On or Off.If "On" is
selected, the alarm host will send SMS to this phone when an alarm
occurs.
Operation Keyboard: Main Menu Parts Add Remoter Enter.
The alarm host displays "Synchronize" and enters into the 20- seconds
countdown dialog window waiting for the remote control synchronization.
Press any key of the remote control to send signal to the alarm host.
The alarm host displays "Learning OK" , then the remote control is
successfully added.
If the alarm host displays “Device code has been learnt”, it means this remote
control is already added to this alarm host, please use other remote control to
try again.
Add
Operation Keyboard: Main Menu Parts Del Remoter Enter.
The alarm host displays “Delete Remoter all”, meanwhile all stored remote
control’s number is displayed in the dialog window.
Press to confirm, the alarm host displays “Operation OK”, all remote control
is deleted.
Operation keyboard: Main Menu Parts Add Detector Enter
It enters into “Set Name and Mode” dialog window
Press to select Name, and press to select the corresponding
name of the zone where the wireless detector is to be added.
Press to select , and then press to select the mode of zone
where the wireless detector is located.
Select , When the alarm host is armed or Stay
armed, the detector will always alarm if triggered,. Suggest to set this
mode of detector in the main door, window, balcony, perimeter area.
Select "Out Armed Active", when the alarm host is Out armed, the
detector will not alarm if triggered. Suggest to set this type of detector
in hall, bedroom area.
Select , the host will alarm at any time once
triggered. Suggest emergency, smoke, gas, carbon monoxide, water
leaks and other detectors to be set to this mode.
Selecting , the alarm host will not alarm at any time if
triggered.
For doorbell, please select , then a tinkling sound arises
from the alarm host whenever the doorbell is pressed.
"Stay armed Active"
"24 hours Active"
"Close"
“Doorbell”
Continuously press Power On/Off key for 5 times, the alarm host will restart, then
system initialization is finished. After system initialization, all the data including
remote control, wireless detector, RFID card, language and time zone and other
setting are reset to factory default . IP address is cleared and the alarm host is
offline GPRS. The IP address needs to be set again to assure the alarm host to go
online and connect with intranet center.
all
System initialization
Start
Initial usage
Insert SIM card：
Power on ：
Turn on the alarm host：
Turn off the alarm host：
According to below diagram, insert MICRO SIM card. When a
ticking voice is heard, it means the SIM card is inserted properly.
Plug power adaptor into USB 5V jack to turn on power.
Press Power On/Off key, a “welcome” window appears,
then the alarm host is turned on.
Press and hold Power On/Off key for 3 seconds until
the screen is off, then the alarm host is turned off.
!
Description for operation keys
Press Previous and Next key to select menu。
Press Return key to last menu。
Press Enter key to next menu。
1. When is used as backspace key, long press to delete all input information.
2. For the other function which is not mentioned in this paragraph, please refer to the
description in the “Menu Structure”.
3. Some operation in this paragraph like phone number setup, add/delete remote control,
add/delete wireless detector and Synchronization with external wireless siren also can
be realized via APP.
!
98
Please be cautious to use this function. Normally it is only used when user forgets password,
or alarm host malfunction, or the parameter is wrongly set, or unknown detector, remote
control or RFID card are learnt.
Menu operation
Phone number setup
The host can set up to maximum 5 groups of alarm numbers, each set of numbers
can be set independently of their dial-up switch and SMS switch.
Take example as phone number 1:
Press to confirm, the alarm host will display "Setting OK".
Add/Delete remote control
Delete
Add/Delete wireless detector(included doorbell alarm)
Add
INITIAL USAGE INITIAL USAGE