sWiFi/all User Manual Version 1.1.1 2020/12/18 www.sysbas.
Revision History Revision Date Document Ver. Pages Revised Revised/Added/Removed Details of Revision 2020.08.15 1.0 All - New 2020.12.18 1.
sWiFi/all User Manual Contents 1. WIFI TECHNOLOGY ......................................................................................................... 4 2. COMPONENTS ................................................................................................................. 5 3. PRODUCT ......................................................................................................................... 6 4. FEATURE .............................................................................
sWiFi/all User Manual Please be sure to read this manual before using and use the product safely and accurately. • Pictures and photos in the manual may be different from the physical, and the document is subject to change without notice to improve performance. For the last information, please visit our website (www.sysbas.com). • To view frequently asked questions and answers, please visit our website and find Support –Technical Support –FAQ section.
sWiFi/all User Manual 1. WiFi Technology WiFi(Wireless Fidelity) is any “Wireless Local Area Network(WLAN)” product based on IEEE(Institute of Electrical and Electronics Engineers) 802.11 standard, mainly using 2.4GHz and 5GHz frequency radio band. WiFi-compatible devices use the technology to communicate wirelessly with each other over the WLAN network and wireless access points, enabling them to reach approximately 100 meters indoors and further outdoors.
sWiFi/all User Manual 2.
sWiFi/all User Manual 3. Product LED RDY (Yellow): When in standby mode, LED flashes every 1.0 seconds. When in setup mode, LED flashes every 0.4 seconds. When in Infrastructure mode, turns on when the connection to AP is successful. When in Soft AP mode, turns on when the connection is successful at Client. TXD (Green): Flashes when serial data is sent, turns off if there is no transmission. RXD (Red): Flashes when serial data is received, turns off if there is no reception.
sWiFi/all User Manual Connector DC Adapter, WiFi Antenna Connector(Male) Serial Port(RS232/422/485) PWR: Connect 5V 1A DC adapter included in the package (internal diameter 3.47mm, outer diameter 1.
sWiFi/all User Manual 4. Feature sWiFi/all is a converter that converts wired serial communication to wireless WiFi communication and performs the following functions. 1) Converts serial signals to wireless Converts RS232/RS422/RS485 serial signals which requires cable installation to wireless WiFi signals. 2) Supports Various WiFi wireless communication Supports WiFi wireless communication at low price. Supports IEEE 802.11 a/b/g/n, Dual Band(2.
sWiFi/all User Manual 5. How to Apply Device/PC – AP – Device Connection (Infrastructure) In Infrastructure mode, sWiFi/all performs connection between ComRedirector, TCP Server/Client and UDP via AP. For sWiFi/all to access AP, the IP of the router band can be set to static IP which is a fixed IP, or set as DHCP which the IP is assigned. Each sWiFi/all can be connected to an AP wired PC or laptop to communicate.
sWiFi/all User Manual Device/PC – Device Connection (Soft-AP) Without being connected to AP, sWiFi/all and PC can be connected 1:1 For serial communication. Between two equipment communicates through serial port, with sWiFi/all attached to each end and connected 1:1, wireless communication is available. To perform the sWiFi/all connection and communication, select the operating mode of one sWiFi/all with Soft-AP which operates as AP and the other with Infrastructure so the AP operates as Soft-AP.
sWiFi/all User Manual 6. Get Started Check the input voltage matches 5V 1A and supply the correct voltage. sWiFi/all starts booting at power-on with normal power supply. LED shows the operating status of the model including RDY, TXD and RXD. For detailed information, please refer to CH.3 Product – LED menu. To view or set up an environment of sWiFi/all, use must use sWiFiConfig utility, either directly connected to serial port(RS232) or to the IP Address, the network address where sWiFi/all is operating.
sWiFi/all User Manual (3) Find and connect sWiFi/all via Smartphone App(sWiFiConfig) sWiFiConfig App(smartphone app) enables setting sWiFi/all. sWiFi configuration, network settings and serial port settings are available in sWiFiConfig App. Put sWiFi/all in setup mode, connect smartphone with sWiFi/all via WiFi, and connect to sWiFi/all in sWiFiConfig App. The sWiFiConfig App is for Android only. You can download it from Google Play by searching sWiFiConfig or from SystemBase website download menu.
sWiFi/all User Manual 7. Settings Apply power to sWiFi/all and press the RST(Reset) switch for less than 3 seconds to operate in setup mode. RDY(Yellow) LED flashes every 0.4 seconds at this time. Then run the sWiFiConfig utility and launch the sWiFi>Connect menu on the top menu bar as below. There are two methods to setup sWiFi/all.
sWiFi/all User Manual Login with ID/PW: sWiFi/99999999. Please note that sWiFi is lowercase. ID and password can be changed in the “Information menu” on the below page. [PLEASE NOTE] The IP address of sWiFi/all 10.10.1.1 and TCP Port No. 4000 cannot be changed. If the PC uses WiFi and wired LAN at the same time, if the IP of wired LAN is set to 10.10.1.xxx network, IP conflict may occur in the same band. So please stop using wired LAN and connect sWiFi/all to WiFi.
sWiFi/all User Manual Information Information menu outputs the basic setting information of sWiFi/all. It also performs MCU Firmware Update, settings for the connection ID and PW of sWiFi/all. [Update] button is a button for Firmware(MCU) Update for sWiFi/all devices. Firmware(MCU) is the firmware for the entire operation of sWiFi/all. It can be updated via sWiFiConfig access. Click [Update] to select the firmware file and update. Firmware(Wireless) is the firmware for the Wireless module.
sWiFi/all User Manual Network Setting Network Setup performs sWiFi/all settings related to network. Lower-left cornet shows the information and status of the connected COMport. [Load] button is a button that shows the information of the currently set sWiFi/all. [Save] button is a button that saves the set content of sWiFi/all. Once the settings have been change, please make sure to press the [Save] button and check that the changed values have been applied in the actual equipment.
sWiFi/all User Manual Serial Setting Serial Setup perform sWiFi/all settings related to serial port. [Load] button is a button that shows the information of the currently set sWiFi/all. [Save] button is a button that saves the set content of sWiFi/all. Once the settings have been change, please make sure to press the [Save] button and check that the changed values have been applied in the actual equipment. You can check the [Load] button to re-connect and check the set value again.
sWiFi/all User Manual Reboot After setting up sWiFi/all, press the '[Reboot] button to restart sWiFi/all and change it to operating mode. Click [Reboot] Reboot succeeded WebPage The WebPage is used to register for WPA-Enterprise, WPA2-Enterprise among the encryption modes of sWiFi/all or to update firmware(wireless). There are three WebPage access methods as below. - sWiFi/all is in setup mode, sWiFi/all and PC are connected via WiFi Access Web using the default IP 10.10.1.
sWiFi/all User Manual On File System menu, you can delete the CA, Client, Key files uploaded from the Security page. Select the authentication certificate file you want to delete and click [Delete] button. Firmware Update in the Etc menu is Firmware(Wireless) Update of sWiFI/all. Click the [Select File] button to select the Wireless firmware file and update. Firmware(MCU), the firmware for the entire operation of sWiFi/all can be updated with sWiFiConfig access.
sWiFi/all User Manual Example of Using Setup Method Based on the above information, we explained the information that can be easily set up through various connections. Please understand the setup method with an example of the configuration below. Infrastructure #1 Setup PC Connected LAN ( or PC Connected WiFi ) sWiFi/all-1 (or sWiFi/all-2) Network Device IP Address: 192.168.0.100 Subnet Mask: 255.255.255.0 Gateway: 192.168.0.1 DNS:168.126.63.
sWiFi/all User Manual Infrastructure #2 To set Infrastructure mode Setup sWiFi/all -1 sWiFi/all-2 Network Device Name: sWiFi/all_1 Device IP Address: 192.168.0.100 Subnet Mask: 255.255.255.0 Gateway: 192.168.0.1 DNS:168.126.63.1 Connection Type: Infrastructure Target AP Name: sysbas23 (If you select AP with [AP Scan] button, the AP name is automatically displayed.) Device Name: sWiFi/all_2 Device IP Address: 192.168.0.200 Subnet Mask: 255.255.255.0 Gateway: 192.168.0.1 DNS:168.126.63.
sWiFi/all User Manual Soft-AP #1 To set Soft-AP mode Setup Network sWiFi -1(Soft-AP) PC Connected WiFi Device Name: sWiFi/all_SoftAP1 Device IP Address: 192.168.1.100 Subnet Mask: 255.255.255.0 DNS:168.126.63.1 Device Name: sWiFi/all_2 Device IP Address: 192.168.1.200 Subnet Mask: 255.255.255.0 DNS:168.126.63.
sWiFi/all User Manual Soft-AP #2 To set Soft-AP mode Setup sWiFi -1(Soft-AP) sWiFi/all-2(Infrastructure) Device Name: sWiFi/all_SoftAP1 Device IP Address: 192.168.1.100 Subnet Mask: 255.255.255.0 DNS:168.126.63.1 Network Connection Type: Infrastructure Channel: 10 Target AP Name: sWiFi/all_SoftAP1 Target AP MAC Address: MAC Address of sWiFi/all_SoftAP1 Connection Type: Soft-AP Channel: 10 Security: open Serial Device Name: sWiFi/all_2 Device IP Address: 192.168.1.200 Subnet Mask: 255.255.255.
sWiFi/all User Manual Class A equipment Sellers or users should be aware of the fact that this device is intended for industrial use(Class A), not for residential use. This device has a potential for radio interference during use and may receive harmful interference from other devices.
sWiFi/all User Manual --------------------------------Appendix-----------------------------1. Specification Frequency 2,412 ~2,462 MHz, 5,150 ~ 5,250 MHz, 5,725 ~ 5,850 MHz Standard IEEE 802.11 a/b/g/n ANT Dipole Antenna / Avg 1.5dBi/2.4GHz, -0.7dBi/5GHz Mode Station, Peer to Peer Port 1 Port DB9 (Female), RS232/422/485 Speed Max. 921.
sWiFi/all User Manual 2.
sWiFi/all User Manual 3. Serial Port Pin Specification Pin No. RS232 RS422 RS485 1 DCD TXD- TRXD- 2 RXD RXD+ - 3 TXD TXD+ TRXD+ 4 DTR - - 5 GND GND GND 6 DSR - - 7 RTS - - 8 CTS RXD- - 9 - - - * As DCE (Data Communications Equipment) mode, RS232 port directly connects with DTE port such as PC. * RS422 port cross-connects with DTE port. (Tx- with Rx-, Tx+ with Rx+, Rx- with Tx-, Rx+ with Tx+) * RS485 port connects with DTE port.
sWiFi/all User Manual 4. Setup Utility The main menus of Network Setup are as follows. Menu Default Description Select the IP type to set for device. IP Type choice Static IP Static IP is fixed IP and DHCP is the automatic IP mode assigned from the AP. Device Name sWiFi_all Set the device name. Set the Static IP address of the device. Device IP Address 192.168.0.223 (If the connection type is Static IP, enter the IP address.
sWiFi/all User Manual In Soft-AP mode, encryption mode can be chosen between open, WSA-PSK. Security Key - Enter the password of a AP to access. Set the connection type of sWiFi/all. Infrastructure The mode that intermediate AP performs a sWiFi/all connection and exchanges data. When selecting this type, the AP Scan Button menu appears. Connection Type Infrastructure Soft AP The mode that sWiFi/all performs AP functions.
sWiFi/all User Manual 2.4GHz Bandwidth Use 2.4GHz bandwidth and supports maximum speed of 600Mbps. Channel Auto(2.4G) Set the channel of sWiFi/all. *Channel values may vary by country. Activate/Deactivate the automatic roaming function. Roaming 0 0 deactivates. If you give RSSI value between -100 and -1dbm, it performs automatic roaming if sensitivity become less than that RSSI. Encryption Algorithm TKIP(Temporal key Integrity Protocol) Basic encryption algorithm used on WPA.
sWiFi/all User Manual Main functions of Serial Setup are as below. Menu Default Serial Interface RS232 Description Set the interface of the serial port. Select one between RS232, RS422, RS485NE(Non-Echo) mode. Set the communication speed of the serial port. Baud Rate 9600 ("300", "600", "1200", "2400", "4800", "9600", "14400", "19200", "28800", "38400", "57600", "115200", "230400", "460800", "921600") Data Bit 8 Set the number of bits which make up the byte.
sWiFi/all User Manual Local Port 4001 Target IP Address 0.0.0.0 Target Port 4001 Designate the number assigned to the port. This port is used to wait for network connection in TCP Server and UDP mode. Designate the IP address of the target to connect to in TCP Client mode. Designate the port of the target to connect to in TCP Client mode. Set up if you want to send continuously-received data from the serial port to the socket at once.
sWiFi/all User Manual 5. Certification • KC Number: R-R-STB-sWiFiallV10 Test Item: KN 301 489-1, KN 301 489-17, Electromagnetic Compatibility based on Article 12 Radio Equipment accounted by National Radio Research Agency No. 2019-32. 2019.12.31) • FCC Number: PRO-SWIFIALLV190 Test Item: FCC Part 15 subpart C 15.247, FCC Part 15 subpart E 15.407 • CE Test Item: Radio: EN 300 328 V2.1.1(2016-11), EN 301 893 V2.1.1(2017-05), EN 300 440 V2.1.1(2017-03) EMC: EN 301 489-1 V2.2.3(2019-11). EN 301 489-17 V3.1.
If you have any inconvenience while using the product, please contact us. Email: Working Hour • Purchase/Quotation: overseas@sysbas.com MON ~ FRI 9:00 ~ 18:00 • Technical Support/RMA: tech@sysbas.com www.sysbas.com Tel: Fax: +82-2-855-0501 +82-2-855-0580 Copyright ⓒ 2020 SystemBase Co., Ltd. All Right Reserved.
