BASSO-1010DS User Manual Version 1.0.1 2020/12/8 www.sysbas.
Revision History Revision Date 2020.12.08 Document Pages Ver. Revised 1.
BASSO-1010DS User Manual Contents 1. SERIAL CONVERTER ................................................................................... 4 2. COMPONENTS .............................................................................................. 5 3. PRODUCT ...................................................................................................... 6 4. FUNCTION ..................................................................................................... 7 6. CONNECTION ..............
BASSO-1010DS User Manual Please be sure to read this manual before using and use the product safely and accurately. • Pictures and photos in the manual may be different from the physical, and the document is subject to change without notice to improve performance. For the last information, please visit our website (www.sysbas.com). • To view frequently asked questions and answers, please visit our website and find Support –Technical Support – FAQ section.
BASSO-1010DS User Manual 1. Serial Converter Converter Function of equipment doubles when connected to other equipment, devices, computers and so on. Therefore, communication of equipment is an important factor of both users at industrial sites and end users. In order for the incoming and outgoing data to be transmitted without any problems, each device participating in the communication must be able to recognize the data sent by each other.
BASSO-1010DS User Manual 2.
BASSO-1010DS User Manual 3. Product LED Power (Red): Illuminates at BASSO-1010DS power input (when Power LED switch is ON) Connector Serial Port(RS232, Female) Serial Port(RS422/RS485) Serial Port(RS232, RS422/RS485): The serial port that can communicate.
BASSO-1010DS User Manual 4. Function BASSO-1010DS converts RS232 signal to RS422 or RS485 signal and performs the following functions: 1) Converts RS232 to RS422/485 Converts short distance communication RS232 to long distance communication RS422/RS485. 2) Port Powered This product is designed to operate without external power supply when connected to RS232 connector(DB9) on a PC or any serial device(additional power connection is required when using RS232 for extended use).
BASSO-1010DS User Manual 6. Connection Device – Device#1 Connection(RS422/485) The device-to-device connection is performed by converting RS232 to RS422/485. Wiring1. Device – Device#1 (RS422) Wiring2. Device – Device#1 (RS485) The RS232 port is as DCE(Data Communication Equipment) mode, connected to the DTE port such as a PC in direct connection.
BASSO-1010DS User Manual Device – Device#2 Connection(RS422/485) Connecting BASSO-1010DS to both sides of two RS232-communicating devices enables RS232 long distance communication. Wiring1. Device – Device#2 (RS422) Wiring2.
BASSO-1010DS User Manual Device – Device#3 Connection(RS422/RS485 Multi-Drop) Wiring1.
BASSO-1010DS User Manual Wiring2.
BASSO-1010DS User Manual 6. Settings Set the setting switch on bottom of BASSO-1010DS to the desired mode. Switch No ON OFF 1 RS485 RS422 2 Echo(RS485 Only) Non-Echo(RS485 Only) 3 RS422 Termination 4 Rs485 Termination Turn switch 1 ON to operate as RS485, OFF to operate as RS422. (Default: RS422) Turn switch 2 ON to operate in RS485 Echo mode, OFF to operate RS485 Non-Echo mode. (Default: Non-Echo) Turn switch 3 ON to activate RS422 termination resistor.
BASSO-1010DS User Manual Class A equipment Sellers or users should be aware of the fact that this device is intended for industrial use(Class A), not for residential use.
BASSO-1010DS User Manual -------------------------APPENDIX-----------------------1. Specifications Standards RS232(DB9 Female), RS422/485(Terminal Block) Maximum Speed 921.
BASSO-1010DS User Manual 2.
BASSO-1010DS User Manual 3. Serial Port Pin Specification Pin No. RS232 1 DCD 2 RXD 3 TXD 4 DTR 5 GND 6 DSR 7 RTS 8 CTS 9 - [Caution] DCD, CTS, DSR signals are not used. DTR and RTS is used for power supply. The RS232 port is as DCE(Data Communication Equipment) mode, connected to the DTE port such as a PC in direct connection.
BASSO-1010DS User Manual Copyright Copyright ⓒ 2020 SystemBase CO., Ltd. All rights reserved. This manual is a document protected by Copyright law. Unauthorized copying, duplicating, publishing of some or all of contents without prior consent from SystemBase is against Copyright Law. www.sysbas.
If you have any inconvenience while using the product, please contact us. Working Hour Email: • Purchase/Quotation: overseas@sysbas.com MON ~ FRI 9:00 ~ 18:00 • Technical Support/RMA: tech@sysbas.com www.sysbas.com Tel: +82-2-855-0501 Fax: +82-2-855-0580 Copyright ⓒ 2020 SystemBase Co., Ltd. All Right Reserved.
