Geniox GO User manualv7.2

ManualsBrandsSystemair ManualsAir Handling UnitsGeniox GO - Madam

Table Of Contents

A Manufacturer
B Name of machines
C Declaration of Conformity
D General descriptions, dangers and warnings
- D.1 Overview via pictograms on the inspection side of the unit
- D.2 Dimensions of the units
E The control panel for the control system.
F Drawings, diagrams, guides and instructions for the use, maintenance and repair
G Employees in charge of operation/control/maintenance
H Unintended use and misuse – inappropriate applications for the machine
- H.1 Air handling unit in operation
I Instructions for unloading and handling on site
- I.1 Delivery types
- I.2 Handling methods
- I.3 Warnings
- I.4 Handling examples
J Installation
- J.1 Installation - mechanical
- J.2 Installation - electrical
  - J.2.1 Installation of cable sealing boxes (only in rotor sections of Geniox GO 27—31)
- J.3 Installation – Pipes for water – hot and chilled, valves and drains
K Installation and assembly instructions for reduction of noise and vibration emissions
L Start-up, adjustments, use and commissioning
- L.1 Print-outs on paper
- L.2 Start-up by installer
  - L.2.1 Remove rotor lock plate
  - L.2.2 Checklist, relevant values
- L.3 Description of functions
- L.4 Commissioning
M Information about the residual risks
- M.1 Unit casing
N Instructions on the protective measures during repair and maintenance
O The essential characteristics of tools which may be fitted to the machinery
P The conditions of stability during use, transportation, assembly, dismantling when out of service
- P.1 Installed reliable to avoid units to be tilted or moved by storm
- P.2 Transport of section with heat pump unit
- P.3 Disposal of the heat pump system
- P.4 General disassembly – sharp edges
Q Instructions for machinery where these are regularly to be transported
R The operating method to be followed in the event of breakdown. Safe restart.
S Adjustment and maintenance operations
- S.1 Shutdown of the unit to a safe state
- S.2 Recommended maintenance intervals
- S.3 Filters – always replace filters with new filters with the same characteristics to maintain SFP value
- S.4 Changing the Internal Battery in the controller
- S.5 Other functions to maintain
T Instructions to enable adjustment and maintenance safely
- T.1 Protective measures and additional protective measures
U Information on airborne noise emissions exceeding 70 dB(A)
Annex 1 Technical data – unique data for every unit (in separate cover)
Annex 2 Assembly of base frame – height 118 mm for unit sizes 10 – 18
- 2.1 Base frame length 482 – 2564 [mm] Unit size 10 – 18
- 2.2 Base frame length 2582 – 4964 [mm] Unit size 10 – 18
- 2.3 Base frame length 4982 – 6164 [mm] Unit size 10 – 18
Annex 3 Assembly of base frame – height 118 mm for unit sizes 20 – 27
- 3.1 Base frame length 482– 2564 [mm] Unit size 20 – 27
- 3.2 Base frame length 2582 – 4964 [mm] Unit size 20 – 27
- 3.3 Base frame length 4982 – 6164 [mm] Unit size 20 – 27
Annex 4 Assembly of base frame – height 218 mm for unit sizes 10 – 18
- 4.1 Base frame length 482– 2564 [mm] Unit size 10 – 18
- 4.2 Base frame length 2582 – 4964 [mm] Unit size 10 – 18
- 4.3 Base frame length 4982 – 6164 [mm] Unit size 10 – 18
Annex 5 Assembly of base frame – height 218 mm for unit sizes 20 – 27
- 5.1 Base frame length 482– 2564 [mm] Unit size 20 – 27
- 5.2 Base frame length 2582 – 4964 [mm] Unit size 20 – 27
- 5.3 Base frame length 4982 – 6164 [mm] Unit size 20 – 27
Annex 6 Installation of steel roof in the sizes 10 – 31
- 6.1 Warnings
Annex 7 Speed control for rotor and assembly of divided rotor
- 7.1 Speed control type NOVA drive 370 delivered after February 2021
  - 7.1.1 Selection of correct signal via the 5 DIP switch levers in NOVA drive 370
- 7.2 Speed control RHC 200 delivered before March 2021
- 7.3 Assemble of split rotor for Geniox GO 27, Geniox GO 29 and Geniox GO 31
Annex 8 Reversible heat pump unit (in separate cover, if heat pump was delivered)
Annex 9 Menu for internal controller in the heat pump unit (in separate cover, if heat pump was delivered)
Annex 10 Connection of fan motor and set-up manual for frequency converter
Annex 11 Commissioning protocol (in separate cover)
Annex 12 Report with data from final functional test on the Systemair factory
Annex 13 Short description of main components in the control system
- 13.1 Geniox units delivered in one or several sections
  - 13.1.1 External components
Annex 14 Wiring diagram (in separate cover)
Annex 15 Operator’s guide (How to use the Systemair control panel) (in separate cover)

| Adjustment and maintenance operations

This type of water trap is designed for negative pressure. Demount

this type of water trap for careful cleaning.

S.5.5 Run-around heat exchanger

A heat recovery system of this type consists of a heating coil in the supply air- flow and a cooling coil in the exhaust

air- flow. After an extended running period (normally a few years) dust particles can accumulate on the surface of the

coils. This can reduce the efficiency of the coils. Cleaning must be carried out with the utmost care to ensure that the

coil fins are not damaged.

The piping system must be vented once a year as air in the system can significantly reduce the capacity of the coils.

S.5.5.1 Pump and pressure expansion

The service instructions issued by the pump manufacturer must be followed. The pressure expansion system must be

checked once a year. If necessary, the pressure must be increased to the correct level.

S.5.5.2 Condensate water drain

Once a year clean the drip tray beneath the heat exchanger, as well as the drain and the water trap. Take care that

there is sufficient water in the water trap. If a droplet eliminator has been fitted to the cooling coil, this must be checked

once a year and cleaned if necessary.

S.5.6 Coils/batteries for heating and/or cooling

After an extended running period (normally a few years) dust particles can accumulate on the surface of the coil. This

can reduce the efficiency of the coil. Cleaning must be carried out with the utmost care to ensure that the coil fins are

not damaged. The piping system must be vented once a year as air in the system can significantly reduce the capacity

of the coil.

S.5.6.1 Heating battery

Check that the frost protection system is fully operational. A battery may

burst due to frost if the frost protection system is not operational.

211728 | v7.2