Geniox GO User manualv7.2
Table Of Contents
- A Manufacturer
- B Name of machines
- C Declaration of Conformity
- D General descriptions, dangers and warnings
- E The control panel for the control system.
- F Drawings, diagrams, guides and instructions for the use, maintenance and repair
- G Employees in charge of operation/control/maintenance
- H Unintended use and misuse – inappropriate applications for the machine
- I Instructions for unloading and handling on site
- J Installation
- J.1 Installation - mechanical
- J.1.1 Free area in front of and above the unit
- J.1.2 Supporting surface
- J.1.3 Adjustable feet under legs or base frame and transport of sections
- J.1.4 Base frame assembly
- J.1.5 Base frames for outdoor units
- J.1.6 Outdoor units — support under the base frame of the unit
- J.1.7 Installation on the site of unit sections at the base frame when sections are delivered on pallets
- J.1.8 Joining the unit sections
- J.1.9 Fitting the ductwork
- J.1.10 Risk of stack effect by vertical ducts and wind pressure on louvers
- J.1.11 Door alignment
- J.1.12 Lock the doors by using the key
- J.2 Installation - electrical
- J.3 Installation – Pipes for water – hot and chilled, valves and drains
- J.1 Installation - mechanical
- K Installation and assembly instructions for reduction of noise and vibration emissions
- L Start-up, adjustments, use and commissioning
- M Information about the residual risks
- N Instructions on the protective measures during repair and maintenance
- O The essential characteristics of tools which may be fitted to the machinery
- P The conditions of stability during use, transportation, assembly, dismantling when out of service
- Q Instructions for machinery where these are regularly to be transported
- R The operating method to be followed in the event of breakdown. Safe restart.
- S Adjustment and maintenance operations
- T Instructions to enable adjustment and maintenance safely
- U Information on airborne noise emissions exceeding 70 dB(A)
- Annex 1 Technical data – unique data for every unit (in separate cover)
- Annex 2 Assembly of base frame – height 118 mm for unit sizes 10 – 18
- Annex 3 Assembly of base frame – height 118 mm for unit sizes 20 – 27
- Annex 4 Assembly of base frame – height 218 mm for unit sizes 10 – 18
- Annex 5 Assembly of base frame – height 218 mm for unit sizes 20 – 27
- Annex 6 Installation of steel roof in the sizes 10 – 31
- Annex 7 Speed control for rotor and assembly of divided rotor
- Annex 8 Reversible heat pump unit (in separate cover, if heat pump was delivered)
- Annex 9 Menu for internal controller in the heat pump unit (in separate cover, if heat pump was delivered)
- Annex 10 Connection of fan motor and set-up manual for frequency converter
- Annex 11 Commissioning protocol (in separate cover)
- Annex 12 Report with data from final functional test on the Systemair factory
- Annex 13 Short description of main components in the control system
- Annex 14 Wiring diagram (in separate cover)
- Annex 15 Operator’s guide (How to use the Systemair control panel) (in separate cover)
Adjustment and maintenance operations |
35
Size of unit
Numbers and sizes of frames for panel filters (WxHxD)
18
2x[490x392x48] + 4x[592x392x48]
20
3x[592x592x48] + 3x[592x287x48]
22
6x[592x490x48] + 2x[287x490x48]
24
3x[592x592x48] 4x[490x592x48] + 1x[490x490x48]
27
2x[592x592x48] + 8x[490x592x48]
29
6x[592x592x48] + 4x[490x592x48]
31
5x[592x592x48] + 5x[592x490x48] + 5x[592x287x48]
Note:
Special sizes of filters are available by Camfil.
S.3.3 Bag filters
Turn the unit off and wait for 2 minutes till unit completely stops. Used filters can be pulled out. Store the used filters
immediately in plastic bags to avoid that dust pollutes the environment. Geniox GO units in the sizes 10 – 31 are pro-
vided with a very corrosive-resistant and reliable system, where filters are slid into the units in a lower and upper dura-
ble u-profile of plastic/rubber Check the upper and lower U-profile for damage and check the vertical rubber profile on
the back wall as well as the rubber profile on the inspection door for damage. The new filter bags must be pushed care-
fully into the unit in order to ensure that they are sealed properly. The filters must have vertical bags.
ONE self-adhesive foam strip must be placed on the verti-
cal frame of EACH filter to avoid major air leakage through
the vertical opening between 2 filters. Please note – only
ONE self-adhesive foam strip must be placed on the verti-
cal frame of EACH filter – Please establish the practical
rule that the self-adhesive foam strip is placed on the ver-
tical side that is visible from the inspection side. Those
very important self-adhesive foam strips are usually not
delivered by the suppliers of filters. The customer must
order those self-adhesive foam strip from a supplier of
foam strips. The foam strip must be wide enough to pre-
vent air leakage between the filters but not too wide to
allow closing the inspection door. Note! The staff must
have the self-adhesive foam strips available when they
go to the air handling unit. Without those self-adhesive
foam strips, any change of filters is impossible.
Remove the protection from the self-adhesive side of the
strip.
211728 | v7.2