Modbus Parameter Specifications
Table Of Contents
- Change history
- 1 Protocol frame
- 2 Holding registers
- 2.1 Overview
- 2.2 Reset
- 2.3 Set value
- 2.4 Password
- 2.5 Factory setting Control
- 2.6 Customer setting Control
- 2.7 Operating hours counter
- 2.8 Operating minutes counter
- 2.9 Addressing on/off
- 2.10 Stored set value
- 2.11 Enable RS485
- 2.12 Fan address
- 2.13 Set value source
- 2.14 Preferred running direction
- 2.15 Store set value
- 2.16 Mode of operation
- 2.17 Direction of action
- 2.18 Control parameters
- 2.19 Maximum modulation level
- 2.20 Minimum modulation level
- 2.21 Motor stop enable
- 2.22 Starting modulation level
- 2.23 Maximum permissible modulation level
- 2.24 Minimum permissible modulation level
- 2.25 Maximum speed
- 2.26 Maximum permissible speed
- 2.27 Ramp-up/ramp-down curve
- 2.28 Speed limit
- 2.29 Input characteristic curve
- 2.30 Maximum power
- 2.31 Maximum permissible power
- 2.32 Speed monitoring speed limit
- 2.33 Sensor actual value source
- 2.34 Interface settings
- 2.35 Rotating direction fail-safe mode
- 2.36 Fail-safe set value source
- 2.37 Set value for fail safe function
- 2.38 Time lag fail-safe speed
- 2.39 Cable break detection voltage
- 2.40 Sensor
- 2.41 Enable source
- 2.42 Stored enable RS485
- 2.43 Customer data
- 2.44 Error history
- 2.45 DC-link voltage reference value
- 2.46 DC-link current reference value
- 2.47 Manufacturing data
- 2.48 Air flow reference value
- 2.49 Mass flow reference value
- 2.50 Mirror function for holding registers
- 2.51 Mirror function for input registers
- 2.52 Mass flow calculation
- 3 Input registers
- 3.1 Overview
- 3.2 Identification
- 3.3 Maximum number of bytes
- 3.4 Bus controller software name
- 3.5 Bus controller software version
- 3.6 Commutation controller software name
- 3.7 Commutation controller software version
- 3.8 Actual speed
- 3.9 Motor status
- 3.10 Warning
- 3.11 DC-link voltage
- 3.12 DC-link current
- 3.13 Motor temperature
- 3.14 Temperature inside electronics
- 3.15 Current modulation level
- 3.16 Current set value
- 3.17 Sensor actual values
- 3.18 Enable input state
- 3.19 Current controller function
- 3.20 Current power
- 3.21 Current set value source
- 3.22 Energy consumption counter
- 3.23 Heartbeat
- 3.24 Mirrored input registers
MODBUS ACE V1.00
_______________________________________________________________________________________
ebm-papst Mulfingen GmbH & Co. KG
Bachmühle 2 ·74673 Mulfingen ·Phone: +49 (0) 7938/81-0 ·Fax: +49 (0) 7938/81-110 ·www.ebmpapst.com ·info1@de.ebmpapst.com
DocNo.: 634505DocNo: 446144DocNo.:358982DocNo.:322523DocNo.:309753DocNo.:303997DocNo.:276241DocNo.:256078DocNo.:196392 ·Template: 2 dated 10/6/2003 ·File: ext001931381.docx ·Last printed 9/30/2019 10:29:00
AM ·Page 68 of 78
Form 1003
3.2 Identification
Address : D000
The identification specifies the type of electronics/protocol concerned.
Coding:
Value
Device
Specification Version
00 01
ebm-papst product range 84 / 112 / 150
1.02
*)
00 02
ebm-papst product range 84 / 112 / 150
2.01, 3.00 - 3.01
*)
00 03
Customer application
*)
00 04
Customer application
*)
00 05
Customer application
*)
00 06
ebm-papst product range 84 / 112 / 150
3.02
*)
00 07
ebm-papst product range 84 / 112 / 150
4.00
*)
00 08
ebm-papst product range 84 / 112 / 150 / 200
5.00
*)
00 09
Customer application
*)
00 0A
ebm-papst product range 84 / 112 / 150 / 200 Lite
5.00
*)
00 0B
ebm-papst product range 84 / 112 / 150 / 200 Lite + plug-in module
5.00
*)
00 0C
Special applications for ebm-papst product range 84/ 112/ 150/ 200
5.02
*)
00 0D
ebm-papst product range 84 / 112 / 150 / 200 Lite
5.01
*)
00 0E
ebm-papst product range
6.00 *)
00 10
ebm-papst RadiCal in scroll housing
1.00
*)
Devices with identification ≠ 0x0010 do not correspond to this specification.
In such cases use is to be made of the applicable document.
3.3 Maximum number of bytes
Address : D001
This parameter specifies the maximum number of bytes which can be contained in a telegram via MODBUS.
Coding: