SYSHP MINI EVO P – Installation Operation Manual (IOM SYSHP MINI EVO P S 1GB)

49
T4HMAX
The maximum ambient operating temperature f or heating
mode
25
T4HMIN
The minimum ambient operating temperature for heating
mode
-15
dT1SH 5
T1SetH1
The setting temperature 1 of climate related curves for
heating mode
35
T1SetH2
The setting temperature 2 of climate related curves for
heating mode
28
T4H1
The ambient temperature 1 of climate related curves for
heating mode
-5
T4H2
The ambient temperature 2 of climat
e related curves for
heating mode
7
ZONE1 H-EMISSION 1
ZONE2 H-EMISSION 2
FORCE DEFROST 0
T4AUTOCMIN
The minimum operating ambient temperature for cooling in
auto mode
25
T4AUTOHMAX
The maximum operating ambient temperature f or heating
in auto mode
17
WATER FLOW TEMP. Enable or disable the WATER FLOW TEMP.:0=NON,1=YES 1
ROOM TEMP. Enable or disable the ROOM TEMP.:0=NON,1=YES 0
DOUBLE ZONE
Enable or disable the ROOM THERMOSTAT DOUBLE
ZONE:0=NON,1=YES
0
IBH FUNCTION
0（DHW=valid）
1（DHW=invalid）
IBH LOCATE
The installation location of IBH（PIPE LOOP=0）
0
dT1_IBH_ON 5
P_IBH2 Power input of IBH2 0
AHS FUNCTION 0
AHS_PUMPI CONTROL 0
dT1_AHS_ON 5
30
T4_IBH_ON -5
P_IBH1 Power input of IBH1 0
t_AHS_DELAY
The time that the compressor has run before starting the
additional heating source
30
T4_AHS_ON
-5
EnSWITCHPDC 0
ROOM THERMOSTAT 0
t_INTERVAL_H The start time interval of the compressor in heating mode 5
2dTSH
Enable or disable the FORCE DEFROST function：
0=NON,1=YES
3.3
3.4
3.5
3.8
3.9
3.10
3.11
3.12
3.13
3.14
4.1
4.2
5.1
5.2
5.3
7.1
7.2
7.3
7.7
7.8
7.9
7.10
7.4
7.5
7.6
7.11
7.12
7.13
6.1
3.7
3.6
6.2
MODE SET PRIORITY 0
Select the priority mode in ROOM THERMOSTAT：
0=HEAT,1=COOL
Select the mode that IBH（BACKUP HEATER） can run：
0=HEAT+DHW,1=HEAT
The temperature difference between T1S and T1 for
starting the backup heater.
t_IBH_DELAY
The time that the compressor has run before starting the
first step backup heater.
The ambient temperature for starting the backup heater.
Enable or disable the AHS（AUXILIARY HEATING
SOURCE） function：0=NON,1=HEAT,2=HEAT+DHW
Select the pump operating status when only AHS runs：
0=RUN,1=NOT RUN
The temperature difference between T1S and T1B for
starting the auxiliary heating source
Enable or disable the function that heat pump and auxiliary
heating source switch automatically based on running cost：
0=NON,1=YES
The ambient temperature for starting the additional heating
source
Order
number
Code State Default
/
/
/
/
/
/
/
/
/
/
min
kW
/
/
min
/
Unit
kW
min
°C
°C
°C
°C
°C
°C
°C
°C
°C
°C
°C
°C
°C
°C
The temperature difference between T1 and T1S(the
set water temperature) for starting the heat pump
The temperature difference between actual room
temperature Ta and the set room temperature Tas for
starting the heat pump
Room thermostat type
: 0=NON,1=MODE
SET,2=ONE ZONE
3=DOUBLE ZONE
The terminal type of zone 1 for heating mode: 0=FCU(fan
coil unit), 1=RAD.(radiator), 2=FHL(floor heating loop)
The terminal type of zone 2 for heating mode: 0=FCU(fan
coil unit), 1=RAD.(radiator), 2=FHL(floor heating loop)