EDM SYSHP MINI SPLIT 06 16
Table Of Contents
- CONTENTS
- CONTENTS
- 1.1 System Schematic
- 1.2 System Configurations
- 2 Unit Capacities
- 2.1 Outdoor unit
- 3 Nomenclature
- 3.1 Outdoor unit
- 3.2 Hydronic box
- 4 System Design and Unit Selection
- 4.1 Selection procedure
- 4.2 M thermal Leaving Water Temperature (LWT) Selection
- 5 Typical Applications
- 5.1 Space Heating Only
- 5.2 Space Heating and Domestic Hot Water
- 5.3 Space Heating, Space Cooling and Domestic Hot Water
- 5.4 Space Heating and Domestic Hot Water (Bivalent)
- 5.4.2 Auxiliary heat source provides space heating and domestic hot water
- 5.5 Space Heating Through Floor Heating Loops and Radiators
- 5.6 Space Heating, Space Cooling and Domestic Hot Water Compatible with Solar Water Heater
- Part 2 Engineering Data
- 1.1 Outdoor Unit
- 1.2 Hydronic Box
- 2 Dimensions and Center of Gravity
- 2.1 Outdoor Unit
- 2.2 Hydronic Box
- 3.1 Outdoor Unit
- 4 Wiring Diagrams
- 4.1 Outdoor Unit
- 4.2 Hydronic Box
- 5 Capactiy Tables
- 5.2 Cooling Capacity Tables (Test standard：EN14511)
- 7 Hydronic Performance
- 8.1 Overall
- 8.2 Octave Band Levels
- 9.1 Outdoor Unit
- 1.1 Notes for Installers Boxes
- 2 Installation
- 2.1 Acceptance and Unpacking
- 2.3 Outdoor unit
- 1
- 1.1
- 1.2
- 1.3
- 1.4
- 1.5
- 2.4 Hydronic box
- 3 Refrigerant Pipework
- 3.1 Permitted Piping Length and Level Difference
- 3.3 Procedure and Principles
- 3.4 Storing Copper Piping
- 3.8 Pipe Flushing
- 3.9 Gastightness Test
- 4 Water Pipework
- 4.1 Water Circuit Checks
- 4.2 Water volume and sizing expansion vessels
- 4.3 Water Circuit Connection
- 4.4 Water Circuit Anti-freeze Protection
- 5.1 General
- 5.4 Wiring Overview
- 8.1 Introduction
- 8.2 Menu Structure
- 8.11 HOLIDAY AWAY SETTING Menu
- 8.14 TEST RUN
- 8.15 SPECIAL FUNCTION
- 8.16 AUTO RESTART
- 8.20 HMI ADDRESS SET
- 9 Operation parameter
- 10 Network Configuration Guidelines
- 10.1 Install APP
- 10.2 Sign in
- 10.3 Add device and login to home Wi-Fi
- 10.4 Wired Controller Setting
- 10.4.2 Finishing up
- 11 USB Function Guidelines
- 11.1 Parameters setting transfer between wired controllers
- 11.2 Convenient program upgrade for unit
- 12 Climate Related Curves
- 13 Error Code Table
- Part 1 General Information
- Part 2 Engineering Data
- Part 3
- Installation and Field Settings
- 1 Air-to-Water HP Split System
- 2 Unit Capacities
- 3 Nomenclature
- 4 System Design and Unit Selection
- 5 Typical Applications
- 1 Specifications
- 3 Piping Diagrams
- 4 Wiring Diagrams
- 5 Capactiy Tables
- 6 Operating Limits
- 7 Hydronic Performance
- 8 Sound Levels
- 9 Accessories
- 1 Preface to Part 3
- 3 Refrigerant Pipework
- 4 Water Pipework
- 6 DIP Switch Settings
- 7 Internal Circulation Pump
- 8 User Interface Field Settings
- 9 Operation parameter
- 10 Network Configuration Guidelines
- 11 USB Function Guidelines
- 12 Climate Related Curves
- 13 Error Code Table
95
Abreviaons:
T4: Outdoor ambient temperature
IBH: Backup electric heater
8.10 OTHER HEATING SOURCE Menu
8.10.1 OTHER HEATING SOURCE menu overview
MENU > FOR SERVICEMAN > OTHER HEATING SOURCE
Figure 3-8.26: OTHER HEATING SOURCE menu
Figure 3-8.27: T4_IBH_ON
Abreviaons:
AHS: Addional heang source
T4: Outdoor ambient temperature
In OTHER HEATING SOURCE the following parameters should be set. Backup electric heater is oponal.
dT1_IBH_ON sets the temperature dierence between the heat pump’s leaving water set temperature (T1S) and the heat pump’s
leaving water temperature (T1) above which the backup electric heater heang element(s) are on. When T1S - T1 ≥ dT1_IBH_ON
the backup electric heater is on (on models where the backup electric heater has a simple on/o control funcon).
t_IBH_DELAY sets the delay between the compressor starng and the backup electric heater being turned on.
T4_IBH_ON sets the ambient temperature below which the backup
electric heater is used. If the ambient temperature is above T4_
IBH_ON, the backup electric heater is not used. The relaonship
between operaon of the backup heater and the ambient is shown
in Figure 3-8.27.
dT1_ASH_ON sets the temperature dierence between the heat pump’s leaving water set temperature (T1S) and the heat pump’s
leaving water temperature (T1) above which the addional heang source is on. When T1S - T1 ≥ dT1_AHS_ON the addional
heang source is on.
t_ASH_DELAY sets the delay between the compressor starng and the addional heang source being turned on.
T4_AHS_ON sets the ambient temperature below which the addional heang source is used. If the ambient temperature is
above T4_ASH_ON, the addional heang source is not used. The relaonship between operaon of the addional heang
source and the ambient is shown in the picture below.
Heat mode by
IBH only
Heat mode by heat
pump and IBH
Heat mode by
heat pump
Figure 3-8.28: T4_AHS_ON
Heat mode
by AHS only
Heat mode by heat
pump and AHS
Heat mode
by heat pump
IBH LOCATE means IBH is installed for pipe heang.
P_IBH1, P_IBH2 set heang capacity of IBH and P_TBH sets heang capacity of TBH, which are used for energy consumpon
stascs.