Manual PDK65

ManualsBrandsSystemair ManualsControlsPDK65 Presence detector kit - With power supply for 5 detectors

PEPE

VARNING

Vid fel anlita

elektriker

Fassäkring max 10 A

Denfasta elinstallationen

är delvis spänningsatt.

12 VDC

PDK65

PEPE

Warning

High Voltage!

Maintenance is only allowed

by authorized personnel

No Fuseincluded: ExternalFusemax 10A

WARNING!

The installation of this product requires working

with high-voltage and may only be carried out

by a qualied electrician.

The power must be isolated prior to installation

and opening of the product.

• This product may only be installed using phase circuit

breakers of the following types:

- Automatic circuit breaker 10B.

- Automatic circuit breaker 10C.

- Safety fuse 10A gG.

• Contactors may not be connected to the power supply

without the jumper “Direct/Ext.Cont” being set to “Ext.

Cont”.

• See detailed description in the manual prior to installation.

• Only use this product for its intended purpose (see man-

ual).

• The product should be checked for any damage immedi-

ately after unpacking.

• Should any damage to the product be discovered, do not

proceed with installation under any circumstances what-

soever.

• Cabling may not be laid under the circuit board under any

circumstances.

If for any reason there is suspicion that safe use of the product

cannot be guaranteed, power to the product must immediately

be switched off. It must be ensured that switching on power to

the product cannot be activated unintentionally.

The PDK65 has shared mounting, which means that the detec-

tor can easily be connected with a low voltage cable and posi-

tioned for optimum detection.

The detector is a passive infrared detector with high sensitivity

(passive IR sensor) for presence detection. It has interchangea-

ble lenses which allows you to adapt the detection range.

The power supply is special-

ly adapted for shared mounting

and intended to power the pres-

ence detector. The system is in-

tended for the control of light-

ing xtures on the output side

in communal laundries, ofc-

es, corridors, waste rooms and

bicycle storage rooms.

See technical specica-

tions for switching

power.

The power supply can generally replace the terminal box

housed in the existing junction point between phase in/out and

the power switch in which case it is not necessary to install an

extra power cable. This functions as power supply, output relay

and simple logic module all in one. An external switch for man-

ual on/off can be connected. The power supply also has a con-

nection for earth protection.

Introduction

PDK65 is a complete system with easy installation to control

presence detection in smaller premises.

PDK65 consists of:

• Power supply

• Presence detector

• 3 m cable between module and

detector.

Presence detector for 230 VAC - PDK65

(kit with power supply)

Installation instructions

Presence

detector

Power supply

Summary of content (4 pages)

PAGE 1
Presence detector for 230 VAC - PDK65 (kit with power supply) Installation instructions WARNING! The installation of this product requires working with high-voltage and may only be carried out by a qualified electrician. The power must be isolated prior to installation and opening of the product. • This product may only be installed using phase circuit breakers of the following types: - Automatic circuit breaker 10B. - Automatic circuit breaker 10C. - Safety fuse 10A gG.
PAGE 2
IR detector Power supply Up to five detectors can be connected to the power supply and operate simultaneously. External switches can be connected for switching on and off. The detector is a passive infrared detector (passive IR sensor) intended for presence detection. Several IR sensors can be connected to the same power supply. The detector has a highly sensitive pyroelectric sensor which determines changes in heat radiation.
PAGE 3
S-input Functional and function diagram The S-input detects four different voltage levels (signal types): Function diagrams apply. Green = input signal or internal signal Red = output signal active. Automatic power on When the jumper on the detector is in "Auto", the detector sends the signal "Detect" (2.7 V). The output relay in the power supply then follows the input physical function. Physical input/output S Signal type Function: Automatic power on • Detect (2.
PAGE 4
Technical specifications for Power supply Voltage: 230 VAC. Frequency: 50/60 Hz. Units power consumption: Nominal: 1 W. Max. 5 W. Load: 10 A at 230 VAC, cos φ = 1. 5 A at 230 VAC, cos φ = 0.5. Error indication: The PWR LED flashes slowly as the output type: Ext.Cont (External contactor) is selected or the sinusoidal curve is not detected correctly with power up or down of the relay. Reset: Reset to the correct power up or down or at feed reset. Ambient temperature: - 25 to + 45 oC.