Original instructions SIRe Basic Quick guide SIReB C SE .... 7 GB .... 14 DE .... 21 ES ....28 FR .... 35 IT .... 42 NL ....49 NO .... 56 PL .... 63 RU .... 70 FI ....
SIRe Basic Wiring diagram - Basic SIReB SD230 SIReB1/B2/B1EC C2 Pot. X5 Unit ID C1 X4 230V~ ROOM X3 SIReRTX (optional) SIReUB1 ACTUATOR SUPPLY N L L PE N L ~ SIReCC6XX (max 50 m) L=2m L=1,5m SIReCC6XX (max 50 m) SD230 SIReB1/B2/B1EC C2 Pot. X5 Unit ID C1 X4 230V~ ROOM X3 ACTUATOR SUPPLY N L L PE N L ~ SIReCC6XX (max 50 m) SD230 SIReB1/B2/B1EC C2 Pot.
SIRe Basic Wiring diagram SIReB SIReB1/B2/B1EC C2 Pot. X5 Unit ID C1 X4 230V~ ROOM X3 SIReRTX (optional) SIReUB1 ACTUATOR SUPPLY N L L PE N L ~ SIReCC6XX (max 50 m) L=2m SIReCC6XX (max 50 m) SIReB1/B2/B1EC Pot. Unit ID C2 X5 C1 X4 230V~ ROOM X3 ACTUATOR SUPPLY N L L PE N L ~ SIReCC6XX (max 50 m) SIReB1/B2/B1EC C2 Pot.
1 SE GB Wiring diagram - Advanced SIRe B1/B2/B1EC 2 4
3a Wiring diagram - Advanced 3b OK = ! 3 OK OK = = 4 5 6 2 7 1 8 9 0 ! 4 1 0 5
5 ? 6 www.frico.
SIRe Basic GB Quick guide/Start up Operation without control unit 1. Check that all constituent parts are present (see section Constituent parts). 2. Mount and connect all units and components and where applicable accessories (e.g. actuator), see wiring diagram. When several units are connected set a unique ID for each unit (1-9) which is set in the ID selector of the SIReB1/B2/ B1EC.
SIRe Basic GB Start up 30 - 60 s 2 0. 8 Prevailing room temperature C Set desired room temperature 5 - + 30 °C Set fan steps 1-5 Activate heat 0 = No heat 1 = Heat step 1 possible 2 = Heat step 2 possible (3 = Heat step 3 possible) Heat steps controlled by thermostat.
SIRe Basic GB Constituent parts SIReB C SIReUB1 Wall unit cover SIReCC605 Type Description HxWxD SIReUB1 SIReCC605 Control unit with room temperature sensor Modular cable RJ12 (6/6) 120x70x35 L [m] 5 Option SIReRTX 16 SIReCJ4 SIReCJ6 SIReCC Type Description HxWxD SIReRTX SIReCJ4 SIReCJ6 SIReCC603 SIReCC605 SIReCC610 SIReCC615 SIReCC640 SIReCC403 SIReCC405 SIReCC410 SIReCC415 External room temperature sensor Joint piece for two pcs. RJ11 (4/4) Joint piece for two pcs.
SIRe Basic GB Water control - valve kit VLSP VKF TAC AV SD230 TAC BPV10 BPV10 SD230 AV VOT TRVS SD230 SD230 TRVS Water control - valve system* Type Description Connection VLSP15LF VLSP15NF VLSP20 VLSP25 VLSP32 VOT15 VOT20 VOT25 Pressure independent DN15 Pressure independent DN15 Pressure independent DN20 Pressure independent DN25 Pressure independent DN32 Three way valve and actuator on/off DN15 Three way valve and actuator on/off DN20 Three way valve and actuator on/off DN25
GB SIRe Basic Operating modes Operating modes Air curtains Factory settings gives manual control of fan and heating is controlled by thermostat on/off. Set parameter P04 to 1 (see parameter menu on the next page) to get the thermostat to control both fan and heating on/off. Operating modes fan heaters water Set the maximum fan speed, heating step and desired room temperature. The thermostat is controlling the room temperature by increasing/decreasing the fan speed.
SIRe Basic Installer menu Parameter menu Keep pressed until P00 is shown in the status window. Use arrow up/down to scroll between the parameters. Use arrow up / down to scroll between the parameters. Press once to change a setting in the parameter menu. Flashing values can be adjusted using the arrow up/down and then confirm. Keep the pressed to return to the status window. (Returning automatically to the status window after about 50 seconds). P.P0. 0.01 PPP..0.00222 P 0P.21 3 GB P.
SIRe Basic GB Alarm Cause Action Thermal switch has deployed. One or several motors have overheated. (Only units with withdrawn thermal switches.) Check that nothing is obstructing the unit’s air intake and exhaust. When the overheated motor has cooled the thermal switch shuts again and the alarm can be reset. At repeated alarms, check the motors, replace damaged motors.
Tel: +46 31 336 86 00 mailbox@frico.se www.frico.se For latest updated information and information about your local contact: www.frico.