Original instructions SIRe Basic Air Curtains Electric With quick guide SIReB C For wiring diagram, please see last pages
GB SIRe Basic Air Curtains Electric Quick guide/start up Check that all constituent parts are present (see section Constituent parts). Advice about location Control unit SIReUB1 has an integrated room temperature sensor and is installed so that it is easily accessible to the user. RJ12 (6p/6c) modular cables, which are available in different lengths, are used to connect the PC board and the control unit. Longer cables are available as options. Maximum cable lengths see section Options.
GB SIRe Basic Air Curtains Electric Start up System supplied with power. Three digits 1.4.0. (software version) is quickly shown in th the status window followed by three horizontal lines. After about 30 seconds the prevailing room temperature is then shown in the status window. After the first start up the following basic settings are made. Use arrow up/down and set the desired room temperature, fan speed step and heating step.
SIRe Basic Air Curtains Electric GB Contents Quick guide/start up Advice about location Connect the system Wiring diagrams Enter ID/Operation without control unit Start up 11 11 11 11 12 Constituent parts SIReB 14 Option 15 15 Max.
GB SIRe Basic Air Curtains Electric Constituent parts SIReB Integrated in the air curtain C PE N L SUPPLY 230V X5 C2 SIReUB1, control unit Basic Wall unit cover X4 C1 X3 ROOM ACTUATOR 230V SIReB1, integrated SIReIT, internal PC Board Base temperature sensor SIReCC, modular cable Dimensions constituent parts Type Description SIReUB1 SIReB1 SIRelT SIReCC605 Control unit Integrated PC board Base Internal temperature sensor Modular cable RJ12 (6/6) 14 HxWxD [mm] 120x70x35 L [m] 1 5
GB SIRe Basic Air Curtains Electric Option SIReRTX, external room temperature sensor SIReCJ4, joint piece SIReCJ6, joint piece SIReCC, modular cable Type RSK-no. E-no.
GB SIRe Basic Air Curtains Electric Operating modes Set values Operating modes Use arrow up /down to choose desired room temperature, fan speed step and heating step. Factory settings gives manual control of fan and heating controlled by thermostat at choosen step. Auto mode Change parameter P04 from 0 to 1 (see list of parameters on next page) to active auto mode. Thermostat controls both fan and heating Push the confirm button and the digit(s) starts to flash.
GB SIRe Basic Air Curtains Electric Control unit SIReUB1 Overview Prevailing room temperature C 2 0. 8 Statuswindow Arrow up Scroll up Confirm C Arrow down Scroll down Desired room temperature 20 Fan speed step - Alarm Red led 3 Heating step Run signal Green led _ ON/OFF button 2 Explanations Status window Arrow down The status window has four main displays: prevailing and desired room temperature, fan and heating setps.
GB SIRe Basic Air Curtains Electric Installer menu P.01 Overheating alarm ON/OFF Parameter menu Possibility to block the alarm (only valdid for units with internal temperature sensor). Keep Confirm button pressed until P00 is shown in the status window. Use arrow up / down to scroll between the parameters. Press Confirm button once to change a setting in the parameter menu. Flashing values can be adjusted using the arrow up/down and then confirm.
GB SIRe Basic Air Curtains Electric Alarm and error codes Reset alarm Overheat protection Note! Before resetting, check that the fault is rectified and there is nothing to prevent the unit from being recommissioned! When the fault is rectifed, the alarm is reset according to description below. If "wrong" button is pressed the alarm display disappears but returns in status window after about 20 seconds. At the first start up alarm and error codes can occur, these can usually be reset without action.
GB SIRe Basic Air Curtains Electric Table - Alarm Alarm Cause Action Thermal switch has deployed. One or several motors have overheated. (Only units with withdrawn thermal switches.) Check that nothing is obstructing the unit’s air intake and exhaust. When the overheated motor has cooled the thermal switch shuts again and the alarm can be reset. At repeated alarms, check the motors, replace damaged motors.
SIRe Basic Air Curtains Electric Wiring diagram - Basic 40 X5 C2 SIReB1 X4 C1 X3 ROOM PE N L SUPPLY 230V ACTUATOR 230V 230V~ SIReRTX (optional) SIReUB1 Internal PC Board Base
B1 SUPPLY 230V L N PE N N H1 H2 HEATING PE L ACTUATOR 230V L N C1 X4 N F1 F2 F3 F4 F5 MOTOR / TRAFO ROOM X3 SIReB1 Internal C2 X5 MOTOR INTERNAL PROTECTION SENSOR C2 Pot.
42 X5 C2 SIReB1 X4 C1 X3 ROOM PE N L SUPPLY 230V ACTUATOR 230V 230V~ X5 C2 SIReB1 X4 C1 X3 ROOM PE N L SUPPLY 230V ACTUATOR 230V 230V~ SIReRTX (optional) SIReUB1 SIRe Basic Air Curtains Electric Wiring diagram - Basic - parallell conection
